地面涡研究

 The formation mechanism and the flow characteristics of the ground vortices as well as the method of eliminating ground vortices are studied in this paper. It is noted that, when air is sucked into an aircraft engine, on the ground a momentum moment is exerted on a point sink flow by a lateral wind or a reversed jet from the tail pipe, resulting in the formation of eddy stream known as ground vortices. Through an analysis of numerous experimental data it is found that the ground vortices are composed of two vortices instead of a single and concentrated free vortex.The tangitial velocity distribution curves of the ground vortex can be expressed as two independent functions: one is a directly proportional function located at the core, and the other is an inversely proportional function around the outer surrounding. The pressure distribution is also composed of two parabolic functions.In addition, a method of eliminating the ground vortices is presented, and it is of important engineering significance to eliminate the ground vortices.     

超长大直径钻孔灌注桩桩端承载力研究

阐述了超长大直径钻孔灌注桩桩端承载力的影响因素,包括施工工艺、深度效应和尺寸效应等。分析和对比了目前国内常用的各规范所采用的计算方法。文中算例的计算结果表明,对于同等条件的桩,各规范的计算结果相差较大。采用自平衡试桩法获得了几个重大工程的超长大直径钻孔灌注桩的桩端承载力的实测值。将工程实例的测试结果与各规范的计算结果进行对比,证实了目前规范的计算方法不尽合理。目前各规范中桩端承载力的计算方法是在针对小直径的中短桩的研究基础上建立的。如今,大型桥梁工程中普遍采用超长大直径钻孔灌注桩的情况下,对其桩端承载力的计算应当进行相应的调整,使设计更为合理。     

钢筋砼条基及独立柱基有效高度的实用计算公式

为了便于广大工程实践人员对基础有效高度的确定，根据规范GB50010－2002及GB50007－2002推导求解出基础有效高度的实用计算公式及计算表格。     

用测量法调节某型涡轮的轮背间隙

Cooling Turbine 204050是波音737飞机采用的一种涡轮冷却器,其传统的调节轮背间隙的方法操作繁琐、效率低下。本文介绍了一种测量法来调节204050的轮背间隙,该方法具有可靠性高、操作方便、效率高等优点。     

基于最小一乘的跑道入口高度计算

跑道入口高度是关系着飞机能否安全着陆的关键参数,在其计算中需要采用曲线拟合预测的方法。目前大多是采用基于最小二乘准则的拟合方式。由于最小二乘准则的局限性,当下滑道随机误差不满足正态分布,在飞行数据中出现异常点时会给预测带来较大误差。将最小一乘方法引入到跑道入口高度计算问题中,提高了算法的稳健性,很好地克服了这一问题。     

An equilibrium multi-objective optimum design for non-circular clearance hole of disk with discrete variables

An Equilibrium Multi-objective Optimization Model(EMOM) with self-regulated weighting factors has been proposed for the optimum design of non-circular clearance hole on the front flange of turbine disk. In the ‘‘equilibrium design", both the stress decrease around the hole and the least hole's profile variation are considered, which balances two ambivalent design goals. Specific discrete variables are applied to realize the standardization design in the optimization process, in which a Surrogate Genetic Coding Algorithm(SGCA) is introduced, and a special check module is used to get rid of repeated fitness evaluation of the samples. The method offers an equilibrium design for the non-circular clearance hole of the turbine disk with great accuracy and efficiency.     

跨声速串列转子失速机制的数值研究

为了解决跨声速串列转子的低裕度问题,就必须了解跨声速串列转子的流场结构与失速机制.设计了叶尖切线速度为450m/s,负荷系数为0.56的高负荷跨声速串列转子.基于数值模拟的结果,分析了该串列转子在0.5mm叶尖间隙下的叶尖流场结构与失速机制,并在此基础上分别探讨了叶尖间隙和前、后排叶片周向位置对串列转子特性的影响和失速机制的变化.结果表明:前排叶片的叶尖区域是 影响串列转子稳定性的关键;随着叶尖间隙的增加,串列转子的失速机制也发生变化,从前排叶片叶尖区域的尾迹与径向潜流堵塞后排叶片通道转变为前排叶片叶尖泄漏流堵塞;在较大周向相对位置(后排叶片压力面周向远离前排吸力面)的情况下,串列转子获得最好的效果,随着周向相对位置(PP)的增加,失速部位从后排叶片转移至前排叶片.      

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

平箔片楔形高度对气体止推箔片轴承特性影响

针对波箔型气体止推箔片轴承,建立了箔片结构二维薄板模型,并通过有限差分法和有限元法耦合求解可压缩气体Reynolds方程和气膜厚度方程,获得了给定轴承载荷条件下轴承气膜压力分布、气膜厚度分布、平箔片变形量和功率损耗等轴承特性.通过对比楔形高度分别为25,70,100,200,300μm时的轴承特性仿真结果研究了楔形高度对轴承性能的影响.结果表明:降低楔形高度使轴承气膜压力分布更均匀,并降低了平箔片的局部集中载荷.但楔形高度存在一个最佳值,使得达到相同轴承载荷所需的最小气膜厚度最大,并且轴承具有最小功率损耗,提高了轴承的工作效率.该结果为气体止推箔片轴承的结构设计提供的理论参考.      

边条翼布局流场及其双垂尾抖振特性研究

对边条翼双垂尾布局模型的流场进行了激光片光源显示实验研究。实验在西北工业大学NF-3风洞三元实验段进行。实验记录了沿机身轴向从边条到垂尾后缘共8个剖面位置的流动状态。测试迎角范围10°~35°,风速4m/s。通过边条涡流场随迎角的发展和破裂特性与前期双垂尾抖振实验获得的模型垂尾抖振响应特性的对比分析发现:垂尾翼根弯矩、翼尖加速度响应随迎角的变化均与边条涡的发展状态、是否破裂以及破裂程度密切相关。从而得出结论:边条涡破裂是引起边条翼布局双垂尾抖振的主要原因。