两种轴线相交度测量方法的比较

介绍了两种用准直望远镜测量三轴转台轴线相交度的测量原理和实现方法,对两种方法进行了比较,并指出了测量中应注意的问题。     

天线分析仪控制系统的研制

介绍了天线分析仪控制系统研制过程中的硬件设计关键技术,并提出了轴角转换器控制卡的设计方案,实验表明该方案具有一定的实用性与通用性。     

应用ART1神经网络仿真车间分组

阐述了ART1神经网络在制造单元设计过程中形成零件族的基本方法,并在基于MATLAB的软件平台上,利用其神经网络工具箱对生产过程中的实际情况进行了仿真和应用。     

直升机外挂吊运技术研究

直升机外部吊挂运送物资在国防和国民经济建设中有极为广泛的用途。本文以直8A型机和米171直升机为例，对直升机外挂吊运的飞行性能计算、全机稳定性、吊具系统的设计、飞行员和指挥员、信号员和索具员如何协调等问题进行了研究分析，为今后执行外挂吊运任务的设计和实施，提供了有价值的建议。     

CuAl2／Al复合材料的固相反应合成技术及与Al液的接触反应研究

研究了Ａｌ，Ｃｕ在真空状态下的纯固相接触反应情况，试验表明，Ａｌ粉、Ｃｕ粉在６００℃，保温６ｈ时，两者以完全发生反生成ＣｕＡｌ２（θ相），生成的θ相沿铝基体组织晶界分布并在结晶过程中具有择优取向特性，形成仅含沿晶界方向的主干与垂直于晶界的二次晶轴的树枝晶形貌。     

Plastic wrinkling prediction in thin-walled part forming process:A review

The precision forming of thin-walled components has been urgently needed in aviation and aerospace field. However, the wrinkling induced by the compressive instability is one of the major defects in thin-walled part forming. The initiation and growth of the wrinkles are interac-tively affected by many factors such as stress states, mechanical properties of the material, geometry of the workpiece and boundary conditions. Especially when the forming process involves compli-cated boundary conditions such as multi-dies constrains, the perturbation of clearances between workpiece and dies and the contact conditions changing in time and space, etc., the predication of the wrinkling is further complicated. In this paper, the current prediction methods were summa-rized including the static equilibrium method, the energy method, the initial imperfection method, the eigenvalue buckling analysis method, the static-implicit finite element method and the dynamic-explicit finite element method. Then, a systematical comparison and summary of these methods in terms of their advantages and limitations are presented. By using a combination of explicit FE method, initial imperfection and energy conservation, a hybrid method is recommended to predict plastic wrinkling in thin-walled part forming. Finally, considering the urgent requirements of com-plex thin-walled structures’ part in aviation and aerospace field, the trends and challenges in wrin-kling prediction under complicated boundary conditions are presented.     

基于特征的数控编程技术在航空企业的推广应用

针对国内航空企业飞机结构件数控编程中存在的重复工作量大、效率低、质量不稳定、规范性差等问题,通过面向多主机厂推广基于特征的数控编程技术,切实提高飞机结构件数控编程的效率与质量.首先概述了基于特征的快速程编(FBM NUAA)系统的整体架构,并且介绍了基于特征的数控编程技术在多家主机厂中的推广与应用情况,以及前期推广中遇到的问题,并提出了解决方案.根据多主机厂多机型过百项飞机结构件的实际应用结果表明采用基于特征的快速程编系统进行数控编程,刀轨平均自动生成率超过90％,编程时间较传统编程方式平均缩短70％以上.     

长板件数控加工技术的探索与研究

结合某型机板件在数控加工中的研制生产状况和存在的问题,论述了实现各种长板件类结构零件装夹定位、刀具及其参数、加工方案及程编策略.通过这些技术措施的实施,在一定程度上解决了在加工长板类零件装夹和定位时出现的零件变形、让刀效率低、质量不稳定等问题.     

Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected.     

凸轮型面加工技术探讨

介绍了一种利用加工中心配备专用磨头磨削凸轮复杂型面的特殊加工方法,研究解决了复杂凸轮型面的仿形加工、计量检测及数控加工编程技巧等问题。