A comprehensive survey on the methods of angle of attack measurement and estimation in UAVs

Angle of Attack (AOA) is a crucial parameter which directly affects the aerodynamic forces of an aircraft. The measurement of AOA is required to ensure a safe flight within its designed flight envelop. This paper intends to summarise a comprehensive survey on the measurement techniques and estimation methods for AOA, specifically in Unmanned Aerial Vehicle (UAV) applications. In the case of UAVs, weight constraint plays a major role as far as sensor suites are concerned. This results in selecting a suitable estimation method to extract AOA using the available data from the autopilot. The most feasible and widely employed AOA measurement technique is by using the Multi-Hole Probes (MHPs). The MHP measures the AOA regarding the pressure variations between the ports. Due to the importance of MHP in AOA measurement, the calibration methods for the MHP are also included in this paper. This paper discusses the AOA measurement using virtual AOA sensors, their importance and the operation.     

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

机载托架自动校准系统的设计与实现

为了解决机载托架传统校准方法精度低、耗时、费力等问题,设计了一种高精度、高效率并且操作简单的成品托架自动校准系统。该系统运用调平精度较高的"循环多次"最高点不动调平方法,建立高精度机载托架校准的静力学数学模型,运用VC与Matlab的COM接口编程技术开发机载托架自动校准系统,并建立良好的人机交互界面。试验结果表明,利用该方法对机载托架进行校准,无论是校准精度还是校准效率都较传统方法有很大提高。     

一种基于虚拟页地址映射的NAND Flash管理算法

本文提出了一种基于虚拟页地址映射的NAND Flash管理算法.该算法通过定义坏块表、对应表等结构，以及设计的坏块替换策略和虚拟页地址到实际物理页地址的转换算法，实现上层软件采用虚拟地址对NAND Flash的无坏块连续页地址访问.该算法是一种高效的地址映射算法，能高效地对数据进行索引，占用SRAM空间较少，使系统达到高性能，并使得闪存使用的更加稳定持久.     

FDI飞机舵面损伤故障全局检测的非线性数学模型

阐述了飞机在单舵面损伤故障下 ,建立故障状态下的数学模型 ,以及同样输入条件下飞机正常运动时的数学模型 ,得到飞机在相同飞行条件下损伤时的气动系数和无损伤正常时的气动系数 ,最终得到气动系数的残差。这将为以后飞机过载残差和角加速度残差奠定基础。论文中结合一定的算例给予证实推论的正确性。     

薄膜充气管充气展开特性试验

用展开导轨消除因重力产生的摩擦力,在不同充气速率与初始展开角条件下对薄膜材料充气管的充气展开特性进行了试验研究,获得了展开角,以及展开加速度和内气压的变化规律。试验及分析结果表明:充气管的充气膨胀与展开相互独立,充气膨胀过程近似为等压增容过程,折叠部位的气压变化特性与整体气压变化特性差异明显。     

用亚稳态正电子素研究络合的瞬态反应（Ⅲ）

本文用自制的装有 BaF_2探头的高探测效率的正电子湮没寿命谱仪测量了在室温下正电子素 o-Ps 与 p-RPhG 及 m-RPhG(R=NO_2,Cl,H,CH_3,cH_3O)在20%(V/V)二氧六环水溶液中的络合形成速度常数。实验结果表明,这些o-Ps-M 络合形成速度常数 K 值均与作为配位体的 p-RPhG、m-RPhG 的碱性解离常数 K 的负对数 pK_2 呈线性函数。这表明上述瞬态络合反应满足线性自由能关系,由此可推断出上述络合反应的一些重要性质。     

以培养适用型人才为宗旨建立新型的校外学习中心管理体系

校外学习中心是远程教学和远程学习的活动基地。校外学习中心必须能适应市场经济形势需求,以培养适用型人才为宗旨,不断完善自身机制,实行规范化管理,不断提高教学管理工作水平,建立起新型的管理体系。     

现代激励理论在规范地方政府行为中的作用研究

分析现代激励理论在研究地方政府行为中的作用，并运用现代激励理论提出了规范地方政府经济行为的若干建议。     

钣金制件表面的相贯线求作方法

本文提出钣金制件表面相贯线求作的新方法。