A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

Ionospheric behavior of the F2 peak parameters foF2 and hmF2 at Hainan and comparisons with IRI model predictions

Monthly median values of foF2, hmF2 and M(3000)F2 parameters, with hourly time interval resolution for the diurnal variation, obtained with DPS-4 digisonde observations at Hainan (19.4°N, 109.0°E) are used to study the low latitude ionospheric variation behavior. The observational results are compared with the International Reference Ionospheric Model (IRI) predictions. The time period coverage of the data used for the present study is from March 2002 to February 2005. Our present study showed that: (1) In general, IRI predictions using CCIR and URSI coefficients follow well the diurnal and seasonal variation patterns of the experimental values of foF2. However, CCIR foF2 and URSI foF2 IRI predictions systematically underestimate the observed results during most time period of the day, with the percentage difference ΔfoF2 (%) values changing between about −5% and −25%, whereas for a few hours around pre-sunrise, the IRI predictions generally overestimate the observational ones with ΔfoF2 (%) sometimes reaching as large as ∼30%. The agreement between the IRI results and the observational ones is better for the year 2002 than for the other years. The best agreement between the IRI results and the observational ones is obtained in summer when using URSI coefficients, with the seasonal average values of ΔfoF2 (%) being within the limits of ±10%. (2) In general, the IRI predicted hmF2 values using CCIR M(3000)F2 option shows a poor agreement with the observational results. However, when using the measured M(3000)F2 as input, the diurnal variation pattern of hmF2 given by IRI2001 has a much better agreement with the observational one with the detailed fine structures including the pre-sunrise and post-sunset peaks reproduced reasonably well. The agreement between the IRI predicted hmF2 values using CCIR M(30,000)F2 option and the observational ones is worst for the afternoon to post-midnight hours for the high solar activity year 2002. During daytime hours the agreement between the hmF2 values obtained with CCIR M(30,000)F2 option and the observational ones is best for summer season. The discrepancy between the observational hmF2 and that obtained with CCIR M(30,000)F2 option stem from the CCIR M(3000)F2 model, which does not produce the small scale structures observed in the measured M(3000)F2.     

超燃燃烧室一维流场分析模型的研究

对公开发表的用于超声速燃烧流场分析的几种一维模型进行了研究,指出了其中存在的问题。研究结果表明:基于实验静压数据的一维模型,若不借助必要的流场测量数据或分析结果,或借助于经验性的处理方法,单靠一维假设,无法获得较为完整的一维流场分析结果。改进后的一维模型降低了数据处理过程中的不确定性,提高了对一般情况的适应能力。用编制的计算程序SSC-2对两组典型的超燃燃烧室壁面静压实验数据进行了演算,取得了燃烧室出口总压恢复系数的计算值与测量值基本一致的好结果。     

尺寸参数对气动液阀启动特性的影响

为气动液阀的启动过程建立了数学模型，分析了尺寸参数对该阀启动特性的影响。计算结果表明：在保证必要的工作寿命的前提下，适当地增大控制腔气孔的直径或增大靠近控制腔的活塞端面直径有利于提高该阀的响应能力。本文所得的结论有利于此类阀门的设计。     

固体火箭发动机试验模态分析技术研究

将固体火箭发动机划分为144个自由度，采用锤击法，单点激励多点响应（SIMO）对其在4种工况下进行了频率响应的测量，应用了多种方法进行模态参数识别和数据拟合，并对其结果进行比较，获得了发动机在各工况1kHz以内的各阶固有频率、振型和阻尼，并对试验模态分析技术在固体火箭发动机试验中的应用进行了研究。     

轴对称跨音速流中无激波超音速区的设计

本文直接从音速线出发计算了一个旋成体跨音速绕流超音速泡中的特征线网。提出了从音速线开拓到一条超音速线的方法,计算了无旋轴对称流的特征线网,发现其特点是不能跨越对称轴线,并对其原因作了初步的讨论。本文的计算结果可应用于物面修形。     

The fundamental parameters of the central stars of eight WR ring nebulae

We describe work that has recently been completed on deriving the fundamental parameters of eight WR stars through the photoionization modelling of their surrounding nebulae using non-LTE WR flux distributions. The resulting effective temperatures range from 57 000–71 000 K for the WN4-5 stars and <30 000–42 000 K for the WN6-8 stars. The derived stellar parameters are compared with those obtained from stellar emission line modelling. We find good agreement for the hot early WN stars, indicating that the non-LTE WR flux distributions have essentially the correct shape in the crucial far-UV region. We find lower temperatures for the four cooler late WN stars, particularly for the two WN6 stars. For the nebulae surrounding these stars, we find that the model flux distributions produce too much nebular ionization. We suggest that these discrepancies arise because of the lack of line-blanketing in the WR atmospheres. For the WO1 central star of G2.4+1.4, with strong nebular He II 4686 A emission, we derive a temperature of 105 000 K, somewhat less than previous estimates. The positions of our eight WR stars on the H-R diagram are compared with the evolutionary tracks of Maeder (1990) for solar metallicity. In common with previous workers, we find that our derived luminosities are too low, giving an initial mass range of 25–40 M, below that expected for the majority of WR stars.     

亚超音速机翼最佳弯扭综合设计计算方法

本文介绍一种亚超音速机翼最佳弯扭综合设计的计算方法,它应用了有限基本解方法。分别在亚超音速各选取一个设计点(M数和C_L),进行机翼弯扭设计,其目的是减小与升力相关的阻力。在此基础上,顾及亚音速和超音速这两个设计点的气动力特性,还要兼顾到飞机其它性能和结构上实现的可能性,进行机翼的综合设计。本文分别给出了亚音速最佳弯扭设计,超音速最佳弯扭设计和综合设计的计算结果。经过分析表明,计算结果是合理的。     

反舰导弹变系数修正比例导引研究

针对超音速反舰导弹自导段控制的特点，对比分析了两种典型的非线性导引规律即反馈线性化（FLGL）导引律和逆向接近导引律的优缺点，提出了一种称为变系数修正比例导引的方法，通过对其全弹道仿真结果的分析，说明所提出的导引规律是正确的，具有良好的应用效果。     

超音速斜板进气道侧向溢流估算

 本文采用超音速线化理论,算出斜板侧缘附近干扰区内的流场,并根据流量积分方法,导出了关于流量系数的侧向溢流公式。本文还根据Busemann锥型流理论,应用Carafoli方法,得出了估算侧后掠端板影响的方法和图线。理论计算结果与现有的实验数据作了比较,符合程度很好。