用两端安装法检定热电偶

利用一种设计好的专用检具 ,使两束被检热电偶分别从检定炉的两端安装均可保证符合检定规程的要求 ,从而在不添置新设备的情况下 ,使检定热电偶效率大大提高。     

舰载机着舰时航迹稳定性研究

本文讨论了舰载飞机以小于有利速度着舰时的航迹稳定性问题。在分析飞机航迹稳定性的同时,还对油门杆控制、机动襟翼控制对改善航迹稳定性的作用进行了初步探讨;在此基础上还讨论了舰载飞机加装波束导引系统对着舰过程的影响原理。结果表明:采用油门杆控制、机动襟翼控制来改善着舰阶段的航迹稳定性是可行的:而且用以上两控制系统作为内环的自动驾驶仪在波束导引系统自动导引飞机着舰过程中,能控制飞机的飞行速度、高度,帮助驾驶员操纵。     

精密加工中切削方向毛刺生成机理的研究(英文)

金属切削毛刺是切削加工中产生的常见现象之一。本研究以金属切削实验为基础 ,对二维精密切削中切削方向毛刺的形成过程、主要影响因素及其变化规律进行了系统的实验研究和相应的理论分析 ,结果表明 :( 1 )切削方向毛刺形成过程为正常切削、挠曲变形、弹性效应、继续切削和剪切断裂分离 ;( 2 )发现了切削方向毛刺形成过程中的切屑与工件表面剪切断裂分离的特殊现象 ;( 3)切削方向毛刺尺寸和形态随着切削条件和刀具几何参数的变化而变化。     

电子经纬仪一测回水平方向标准偏差两种检定方法比较

一测回水平方向标准偏差是衡量经纬仪测角精度的主要指标之一.本文结合经纬仪计量检定规程的要求,从测量的原理、方法、不确定度分析等方面入手,对电子经纬仪一测回水平方向标准偏差计量检定的两种方法进行了比较.     

加气喷嘴气体注入形式对雾化性能的影响

本文用马尔文粒度分析仪测量喷雾的平均液滴尺寸及液滴尺寸分布,研究了气体注入形式对喷雾特性的影响.喷嘴压降为34.5～690kPa,喷嘴气液比为0.002～0.023.试验中使用了两种气体注入形式:一种是直径6.3mm的单孔,另一种是20个直径0.5mm的小孔.它们与三种不同孔径的喷孔配合使用.其孔径分别为0.8,1.6和2.4mm.研究结果表明,雾化质量主要取决于喷嘴压降和气液比,而对气体注入形式和喷孔直径不敏感.测量液体流量看出,此类喷嘴的流量系数很小.雾化液体中含有固体颗粒或其它易堵塞小孔或喷嘴通道的有害物时,使用这种喷嘴将会显示出它的优点.     

Numerical simulations of water spray on flame deflector during the four-engine rocket launching

This paper aims to study on the cooling effect with two types of water spray nozzle on the flame deflector during the four-engine launch vehicle take-off. To accurately simulate the two-phase flow of the rocket gas with multispecies and the water spray, the three-dimensional compressible Navier-Stokes equations, discrete ordinates methods and realizable k-Ɛ turbulence model are used to establish the rocket supersonic plumes impact model. The Eulerian dispersed phase (EDP) model was used to simulate the water spray into the exhaust gas. The accuracy and effectiveness of the gas-liquid flow model are verified by a good agreement between simulation results and experimental data. On this basis, a series of numerical simulation studies under different water injection position are performed. The results show that the high temperature regions, along the axis of engines on the deflector plate, have no significant temperature decreasing effect by water spray from the nozzles mounted on the apex of the deflector, and the high temperature converts a large quantity of water into vapor near the plume boundary, which would decrease the flow conductivity. With the cooling spray nozzle fixed directly to the deflector plate, the temperature decrease effect is obvious and the effect of thermal shock on deflector plate induced by exhaust plume is reduced, so that it can prevent the flame deflector from thermal ablation. The study results provide indepth information and engineering guidance for designing the water spray systems and increasing the safety of the launch process.     

自制等离子喷枪冷却系统的设计及测试

等离子喷枪是制备热障涂层中的研究重点。目前关于等离子喷枪的研究多集中于喷嘴(阳极)、阴极,鲜有关于喷枪冷却系统方面的研究;喷枪冷却系统的优劣直接影响喷枪的工作寿命和喷涂过程的稳定性,同时制备热障涂层的质量也与冷却效果紧密相关。本文利用三维模型,详细阐述了自制的喷枪冷却系统通道及工作原理,并对设计进行了理论计算,对自制的喷枪进行点火试验和喷涂测试,结果显示自制的喷枪冷却系统功能良好,喷枪工作稳定,涂层质量较好。     

Application of small-size antennas for estimation of angles of arrival of HF signals scattered by ionospheric irregularities

A modification of the Doppler Interferometry Technique is suggested to enable estimating angles of arrival of comparatively broadband HF signals scattered by random irregularities of the ionospheric plasma with the use of small-size weakly directional antennas. The technique is based on the measurements of cross-spectra phases of the probe radiation recorded at least in three spatially separated points. The developed algorithm has been used to investigate the angular and frequency-time characteristics of HF signals propagating at frequencies above the maximum usable one (MUF) for the direct radio path Moscow-Kharkiv. The received signal spectra show presence of three families of spatial components attributed, respectively, to scattering by plasma irregularities near the middle point of the radio path, ground backscatter signals and scattering of the sounding signals by the intense plasma turbulence associated with auroral activations. It has been shown that the regions responsible for the formation of the third family components are located well inside the auroral oval. The drift velocity and direction of the auroral ionosphere plasma have been determined. The obtained estimates are consistent with the classical conception of the ionospheric plasma convection at high latitudes and do not contradict the results of investigations of the auroral ionosphere dynamics using the SuperDARN network.     

基于ALE法的水陆两栖飞机船体着水性能分析

水陆两栖飞机的着水性能是体现其综合性能的重要因素之一.应用ALE法对三种水陆两栖飞机船体截面进行入水仿真计算,从着水载荷、喷溅性能及运动响应三个方面对着水性能进行综合评估.对比分析了直线型、带舭弯弧形、复合型三种构型截面在不同速度、不同重量下的压力分布、喷溅性能以及运动响应,得到了三种截面横向压力分布规律.计算结果显示相同状态下,喷溅性能复合型优于带舭弯弧形、带舭弯弧形优于直线型;过载复合型远大于带舭弯弧形,带舭弯弧形稍大于直线型,综合看来带舭弯弧形截面着水性能最佳.     

Corrosion mechanism investigation of TiN/Ti coating and TC4 alloy for aircraft compressor application

It is imperative to develop multifunctional erosion and corrosion resistant coatings for compressor blades of aircraft engines in harsh environment. PVD (Physical Vapor Deposition) technology has the advances in processing erosion-resistant coatings; however, the performance of PVD coatings to combat corrosion depends on various coating defects. Determining and comparing the corrosion performances of PVD TiN/Ti coating and uncoated TC4 alloy was the main objective of present work. The 960 h salt spray corrosion and 116 h hot corrosion tests were conducted to simulate the grounding and working environments of the aircraft compressors. The corrosion mechanisms due to the coating defects such as pinhole, columnar boundary and large grain were analyzed based on the OM, Confocal microscope, electrochemical measurements, SEM, XRD and EDS results. Owing to the disordered state associated with the columnar boundary and the coating defect, nitrogen could be easily replaced by oxygen in the hot corrosion process, these structures were channels for fast diffusion of oxygen. Moreover, the Gibbs energy changes of Ti oxidation and TiN oxidation were thermodynamically calculated according to the working condition of aircraft compressors, and considerable research effort was focused on mapping out the phase diagram of Ti, TiN and high pressure gases. The findings of this research can provide insights into developing multifunctional coatings for future aircraft engines.