Modelling of Ejecta as a Space Debris Source

When a micro-debris or a micrometeoroid impacts a spacecraft surface, a large number of secondary particles, called ejecta, are produced. These particles can contribute to a modification of the debris environment: either locally by the occurrence of secondary impacts on the components of complex and large space structures, or at great distance by the formation of a population of small orbital debris. This paper describes firstly, the ejecta overall production, and secondly, the lifetime and the orbital evolution of the particles. Finally the repartition of ejecta in LEO is computed. Some results describing the population as a function of size and altitude are presented.     

Numerical Simulation of Impact Loading on Solid Propellant Within an Orthotropic Shell

The strain–stress state of the solid propellant rocket engines (SPREs) is simulated under impact. The effect of orientation of elastic and strength properties of orthotropic organoplastic shell material on the strain–stress state of the solid propellant is investigated. Normal and oblique impact of single steel cylinder projectiles, both simultaneous and at different times of multiple, converging steel spheric particles with SPRE are investigated in this study. The investigation is conducted numerically. The numerical modeling was carried out in a three-dimensional formulation by the method of finite elements for the continuous approach of the mechanics of a deformable solid. The destruction of the anisotropic material is described by the tensor-polynomial criterion of the fourth degree, which takes into account the influence of hydrostatic pressure.     

混杂纤维缠绕壳体设计

应用网格理论，得到了固体火箭发动机混杂纤维缠绕壳体在内压作用下的平衡方程。给出了混杂纤维缠绕圆筒壁厚的计算公式。讨论了用模拟实验压力容器确定纤维发挥强度的问题。算例表明，文中给出的设计计算方法，可用于混杂纤维缠绕壳体的初步设计。     

固体火箭发动机推力线横移和偏斜模拟计算

分析了固体火箭发动机推力线横移和偏斜的影响因素，介绍了由静态影响因素引起的偏差计算方法，得到的模拟计算结果与实测结果相近。这种计算方法将有助于改进导弹的姿态控制精度。     

固体推进剂远地点发动机的研制和关键技术

自1984年开始,中国研制的系列远地点发动机共9次参加卫星发射,均获成功,表现出很高的可靠性,高空比冲达到2834N·s/kg,质量比为0.895,性能达到了先进水平。该文介绍了远地点发动机的特点、技术水平和主要经验。其中采用丁羟推进剂、玻璃纤维壳体和碳/碳复合材料喉衬被证明为成功的技术选择。在研制过程中,在高空比冲的预示和测量,玻璃纤维壳体基体树脂的研制,高空点火和安全点火机构的研制,防止发动机自旋引起的烧蚀等技术问题方面,积累了丰富经验。对于在高空工作的发动机具有现实参考意义。     

固体火箭发动机地面性能换算成真空性能研究

根据固体火箭发动机内弹道计算模型，分析了使用大扩张比喷管地面静止试验性能与真空性能之间的联系，建立了由地面性能换算成真空性能的方法，计算出的真空推力、真空比冲等数据与实际相符。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

喷射沉积制备Al-Zn-Mg-Cu合金大型坯组织性能的研究

利用Ospray公司的喷射沉积设备制备了Al11.3Zn2.4Mg1.1Cu合金,合金挤压成棒材后,经过固溶和时效处理,用万能材料实验机对其进行了力学性能测试,合金的抗拉强度为849 MPa、屈服强度为796 MPa,延伸率为3.3%.透射电镜和扫描电镜对拉伸试样微观组织的研究结果表明,合金微观组织中包括微米级晶粒和纳米级晶粒,合金的强化方式为纳米晶强化、固溶强化以及沉淀强化,拉伸试样的断口分析表明,合金的断裂方式主要为沿晶断裂.     

正交射流煤粉燃烧器冷态流场的数值计算

本文采用ｋ－ε双方程湍流模型对正交射流煤粉燃烧器出口三维湍回流流动进行了数值研究，得到了副射流与主流速度比为２。５时的正交射流尾迹流场持速度分布、回流特性，并比较了不同速度比时的流场计算结果。计算结果与实测数据符合较好，所得结论对分析正交流燃烧器的稳燃机理具有一定作用。     

固体火箭发动机药柱主动段飞行时应力应变分析

为了探讨固体火箭发动机药柱主动段飞行时的形变、应力和应变变化规律,以星形药型发动机为例,采用三维粘弹性有限元法,根据推进剂药柱的燃烧规律,通过计算发动机药柱在整个工作过程中不同烧蚀情况下各构成部分的结构响应,得到了主动段飞行时发动机药柱在不同环境温度、燃气内压与轴向过载联合作用下位移、应力和应变场随时间的变化规律。结果表明,低温点火发射时,内压增压至峰值时为发动机最危险时刻。