A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

在二元柔壁自适应风洞中利用面元法进行三元模型实验

简要叙述了在西北工业大学二元柔壁自适应风洞中利用面元法进行二元半机翼模型试验的研究情况，分析了面元法的基本思想和部分试验结果。     

随振动量级增加卫星结构频率下移的分析

对卫星振动频率随量级增加而出现下降，即振动频率“漂移”的现象进行了初步分析。发现随振动量级的增加。结构的非线性表现突出。结构的刚度下降和阻尼增加，可认为主要是由蜂窝材料的非线性因素所致。     

翼板颤振主动抑制的无限维非线性分析

 <正> 1.混合动力学系统的Hopf分叉定理 本文将Marsden-McCracken关于分布参数的Hopf分叉定理推广至混合动力学系统。 设在积空间X=E×R~n中依赖参数μ的演化方程为     

运载火箭阻尼安装板的设计

 <正>运载火箭在起飞和着陆时的瞬态载荷和飞行过程中的气动力的随机激励都是宽频带的。在这种环境中安装精密仪器的仪表板若采用过去常规的橡皮减振器减振已很难保证在较宽频带内都能起到应有的减振作用。利用阻尼材料做成的夹层板减振，国内外已做了大量的工作^[t~3]，取得了较为明显的效果。本文针对产品设计中要解决的减振问题，提出了设计思想、计算分析与试验方法。     

三维机身起落架着陆冲击力学模型

 本文根据起落架系统的几何、运动学及动力学特性,推导出目前广泛使用的三维机身式起落架,并具有柔性支柱系统的着陆冲击力学模型。并对其初始条件、对称着陆及不对称着陆情况作了动力学分析。     

简谐激励下弯曲薄板的非线性运动方程

推导了两端固定和两端简支的弯曲薄板在其支承简谐激励下的运动微分方程,并利用Galerkin方法对其进行了离散化处理。     

转轴位置对俯仰动态特性的影响

研究了转轴位置对机翼、机身和三个组合体上翼面的动态特性的影响，对于机翼和机身，当转轴位置后移时其动态迟滞效应更为强烈。当翼面处于转轴之前，上仰时会出现更为的动态迟滞效应。因此鸭翼达到失速状态较晚。而当翼面处于转轴之后时，如尾翼，将会更早地出现动失速，转轴位置对动态迟滞特性的影响可以认为主要是由于俯仰运动时的动态洗流影响所导致的实际有效迎角的变化。由此影响了动态分离涡及其发展。     

基于参数化模型和遗传算法的复合材料加筋壁板结构选型优化研究

针对复合材料加筋壁板的结构优化选型问题,采用辅助层压板和添加极小弹性模量材料的复合材料加筋壁板有限元建模方法,应用PATRAN/NASTRAN的参数化建模功能和遗传算法相结合的复合材料加筋壁板的优化方法,对5种复合材料结构形式进行了从2000N/mm到6000N/mm压缩载荷下的结构优化分析。结果表明,当载荷小于4500N/mm时,最有效的加筋壁板结构型式为J型;当压缩载荷大于4500N/mm时,最有效的加筋壁板结构型式为I型。     

外翼上壁板根部连接形式对飞机承载能力的影响研究

在飞机结构设计中,外翼上壁板根部连接处结构形式对飞机的传力、变形、承载能力具有重要影响.通过对3种不同形式的上壁板根部连接方案进行压缩试验,研究各方案的承载能力、破坏方式.通过三维有限元方法,计算了连接部位的主要螺钉所分配的载荷,研究了长桁根部斜角对结构屈服载荷的影响,得到了最优的选型方案.