A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

在二元柔壁自适应风洞中利用面元法进行三元模型实验

简要叙述了在西北工业大学二元柔壁自适应风洞中利用面元法进行二元半机翼模型试验的研究情况，分析了面元法的基本思想和部分试验结果。     

随振动量级增加卫星结构频率下移的分析

对卫星振动频率随量级增加而出现下降，即振动频率“漂移”的现象进行了初步分析。发现随振动量级的增加。结构的非线性表现突出。结构的刚度下降和阻尼增加，可认为主要是由蜂窝材料的非线性因素所致。     

实时曲面纹理及其光照效果的生成

依据两步映射法和体纹理的思想，将曲面纹理的映射过程分为非实时映射和实时查询两个部分，提出一种能实时显示曲面纹理的方法及相应的抗混叠措施，最后，结合一种快速浓淡算法，为曲面纹理叠加光照效果，生成了很逼真的图象。     

翼板颤振主动抑制的无限维非线性分析

 <正> 1.混合动力学系统的Hopf分叉定理 本文将Marsden-McCracken关于分布参数的Hopf分叉定理推广至混合动力学系统。 设在积空间X=E×R~n中依赖参数μ的演化方程为     

运载火箭阻尼安装板的设计

 <正>运载火箭在起飞和着陆时的瞬态载荷和飞行过程中的气动力的随机激励都是宽频带的。在这种环境中安装精密仪器的仪表板若采用过去常规的橡皮减振器减振已很难保证在较宽频带内都能起到应有的减振作用。利用阻尼材料做成的夹层板减振，国内外已做了大量的工作^[t~3]，取得了较为明显的效果。本文针对产品设计中要解决的减振问题，提出了设计思想、计算分析与试验方法。     

简谐激励下弯曲薄板的非线性运动方程

推导了两端固定和两端简支的弯曲薄板在其支承简谐激励下的运动微分方程,并利用Galerkin方法对其进行了离散化处理。     

大曲率弯道和叶栅内的湍流数值模拟

本文在贴体曲线坐标系下应用非交错网格技术，发展了适于求解复杂流动的压力修正算法，采用速度的协变物理分量为动量方程的求解变量，推导得出一个适于任何曲线坐标系下控制单元体界面流通量的插值模式，可以有效地抑制不合理的波动压力场，计算表明，算法稳定收敛，计算值与试验值吻合良好，同时能预示通道内复杂的流动现象。     

激波过弯道绕双圆柱流场

采用单曝光光栅干涉或双曝光光栅干涉，研究激波过弯道绕双圆柱传播的微波流场。采用单曝光法，成功显示入射激波到第一圆柱上的反射、绕射，到达第二圆柱上的反射、绕射。在同一底片上采用双次曝光，第一次脉冲记录直道上的平面波，第二次脉冲记录激渡过弯道绕双圆柱流场。这些照片对于研究反射、绕射及它们边界的相互作用是很有用的。     

基于参数化模型和遗传算法的复合材料加筋壁板结构选型优化研究

针对复合材料加筋壁板的结构优化选型问题,采用辅助层压板和添加极小弹性模量材料的复合材料加筋壁板有限元建模方法,应用PATRAN/NASTRAN的参数化建模功能和遗传算法相结合的复合材料加筋壁板的优化方法,对5种复合材料结构形式进行了从2000N/mm到6000N/mm压缩载荷下的结构优化分析。结果表明,当载荷小于4500N/mm时,最有效的加筋壁板结构型式为J型;当压缩载荷大于4500N/mm时,最有效的加筋壁板结构型式为I型。