Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

用测量法调节某型涡轮的轮背间隙

Cooling Turbine 204050是波音737飞机采用的一种涡轮冷却器,其传统的调节轮背间隙的方法操作繁琐、效率低下。本文介绍了一种测量法来调节204050的轮背间隙,该方法具有可靠性高、操作方便、效率高等优点。     

An equilibrium multi-objective optimum design for non-circular clearance hole of disk with discrete variables

An Equilibrium Multi-objective Optimization Model(EMOM) with self-regulated weighting factors has been proposed for the optimum design of non-circular clearance hole on the front flange of turbine disk. In the ‘‘equilibrium design", both the stress decrease around the hole and the least hole's profile variation are considered, which balances two ambivalent design goals. Specific discrete variables are applied to realize the standardization design in the optimization process, in which a Surrogate Genetic Coding Algorithm(SGCA) is introduced, and a special check module is used to get rid of repeated fitness evaluation of the samples. The method offers an equilibrium design for the non-circular clearance hole of the turbine disk with great accuracy and efficiency.     

Flow mechanism between purge flow and mainstream in different turbine rim seal configurations

The rim seal is used to prevent mainstream ingestion to the gap between the vane of a turbine and its blade. In this article, the dolphin lip with a hook configuration and a large seal cavity with hook structures are designed based on the high-pressure turbine datum single shark lip rim seal configuration. The sealing effect and parameters of the flow field are measured by an experiment method and a numerical simulation is used to explain the mechanism. For three configurations, the effect of the leakage slot vortex on the efficiency of the seal and the influence of leakage vortex, generated by the interaction between purge flow and mainstream flow, are discussed in depth. The result shows that the reverse vortex formed by the dolphin lip rim seal with hook structure will increase the sealing efficiency. The seal configuration with a large cavity improves sealing efficiency to a greater extent than the datum structure. At different purge flow rates and with unequal seal structures, the purge flow produces three types of leakage vortices in the passage. Besides, the seal configuration with dolphin lip produces a Kelvin-Helmholtz instability at the interface of the purge and the mainstream flows at a low purge flow rate to induce new leakage vortex branches in the passage of the blade.     

跨声速串列转子失速机制的数值研究

为了解决跨声速串列转子的低裕度问题,就必须了解跨声速串列转子的流场结构与失速机制.设计了叶尖切线速度为450m/s,负荷系数为0.56的高负荷跨声速串列转子.基于数值模拟的结果,分析了该串列转子在0.5mm叶尖间隙下的叶尖流场结构与失速机制,并在此基础上分别探讨了叶尖间隙和前、后排叶片周向位置对串列转子特性的影响和失速机制的变化.结果表明:前排叶片的叶尖区域是 影响串列转子稳定性的关键;随着叶尖间隙的增加,串列转子的失速机制也发生变化,从前排叶片叶尖区域的尾迹与径向潜流堵塞后排叶片通道转变为前排叶片叶尖泄漏流堵塞;在较大周向相对位置(后排叶片压力面周向远离前排吸力面)的情况下,串列转子获得最好的效果,随着周向相对位置(PP)的增加,失速部位从后排叶片转移至前排叶片.      

螺旋槽端面气膜密封结构高温特性研究

为了研究螺旋槽端面气膜密封结构在高温下的密封性能,建立了高温密封分析数学模型,研究了螺旋槽气膜密封的气膜温度、压力以及端面变形分布规律,在此基础上探讨了螺旋槽气膜密封的热变形机理,并进一步分析了不同密封压力、转速、环境温度下热效应对开启力和泄漏率的影响。结果表明:在高压、高速条件下,热效应使端面形成发散间隙,导致开启力减小,泄漏率增加;在低压、高速条件下,热效应使端面形成收敛间隙,导致开启力及泄漏率增大。对于螺旋槽端面气膜密封结构,环境温度的升高对端面变形的影响不明显,且环境温度从300 K升至550 K时,考虑端面热效应的开启力减小4%,泄漏率减少36%。     

某航天器输氢管道系统结构完整性评估

为保障某航天器在服役年限内不发生事故,针对航天器上采用插入焊接技术的精密管道系统进行结构完整性评估。在考虑到系统存在整圈的环形未焊透缺陷基础上,结合工程实践,假设在焊接区域存在更危险的平面缺陷。首先,开展高压气相热充氢试验下的标准拉伸和三点弯试验得到管道系统材料"J-75"在临氢环境下应力应变曲线和断裂韧性。其次,采用有限元程序计算系统在内压、惯性载荷与离面位移作用下的应力分布,考虑到间隙配合中的不确定性,改变模型中的最大间隙多次模拟计算,发现最大应力位置基本不变,以此区域作为假想缺陷的具体萌生区域。最后,采用失效评估图（FAD）方法对存在4种缺陷模式的系统分别进行结构完整性评估。通过引入安全裕度的概念,发现系统在含有初始尺寸（0.15 mm）的4种平面缺陷时,均处于安全状态,并且安全裕度都在2倍以上;通过工程临界分析（ECA）发现随着缺陷尺寸的增大,系统中含有缺陷2（位于管道焊接区域最大应力处的轴对称平面且沿焊深方向扩展的缺陷）时最为危险,且当缺陷深度超过0.61 mm时将断裂失效;考虑到测试数据的弥散性,针对系统最危险的模式,以安全裕度为可靠性指标,将失效评估图方法与可靠性评价相结合,得到系统在含有尺寸为0.15 mm的缺陷2情况下保有足够安全裕度的可靠性下限值超过0.999 5。     

旋转对固体火箭发动机燃烧室燃气流动的影响

采用RNG k-ε湍流模型,计算了某管状装药旋转固体火箭发动机在不同旋转速度情况下的燃烧室喷管统一流场,着重分析了不同转速情况下燃烧室内燃气流动的特点,得到了该发动机燃烧室内旋流切向速度沿径向分布趋势以及旋流涡核半径在不同转速情况下的变化特点,对燃烧室前封头局部区域的流场结构也进行了较为细致的分析.     

涡轮叶尖泄漏流被动控制数值模拟

结合基于密度修正的采用雷诺应力湍流模型加壁面函数的三维计算流体力学程序,通过在叶尖吸力面表面加肋条的被动控制方法以期减小叶尖间隙泄漏流动带来的损失,对某一轴流涡轮转子叶尖间隙泄漏流场的被动控制进行了数值模拟研究,并详细分析了在不同肋条高度下泄漏流场细节,最后计算了涡轮效率。结果表明,在涡轮叶尖表面沿吸力面边缘镶肋条对泄漏流动进行被动控制,相对于与其相对叶尖间隙高度相等的基本间隙流场,涡轮效率增大;肋条高度对涡轮效率有较大影响,相对等绝对叶尖间隙高度的基本流场,增大肋条高度可以提高涡轮效率。在叶尖间隙区域前半部,肋条对泄漏流动的阻挡作用使得在叶尖表面出现回流区,阻碍泄漏流动;在叶尖间隙区域后半部,回流区消失。     

造型细节和离地间隙对轿车气动性能的影响

应用FLUENT软件,分别对汽车造型的不同处理方法、发动机安放位置、离地间隙、发动机舱冷却风的排出模式进行气动性能仿真.结果表明:汽车造型的处理方法中以加车轮对气动性能影响最大,发动机存在最佳的安放位置,不同的离地间隙对仿真结果影响很大,选择发动机舱冷却风的排出模式要综合考虑阻力系数和升力系数.