Effect of moderate geomagnetic storms on equatorial plasma bubbles over eastern Africa in the year 2012: Evolution and electrodynamics

Equatorial plasma bubbles (EPBs) are common features of the equatorial and low-latitude ionosphere and are known to cause radio wave scintillation which leads to the degradation of communication and navigation systems. Although these structures have been studied for decades, a full understanding of their evolution and dynamics remains important for space weather mitigation purposes. In this study, we present cases of EPBs occurrences around April and July 2012 geomagnetic storm periods over the African equatorial sector. The EPBs were observed from the Communications/Navigation Outage Forecasting System (C/NOFS) and generally correlated well to the ionospheric irregularities observed from the Global Positioning System total electron content (GPS-TEC) measurements (rate of TEC change, ROT). This study revealed that the evolution of the EPBs during moderate storms is controlled by the strength of the daytime equatorial electrojet (EEJ) currents regardless of the strength of the equatorial ionization anomaly (EIA), the latter is observed during the July storm case in particular. These effects were more evident during the main and part of the early recovery phases of the geomagnetic storm days considered. However, the evening hours TEC gradients between regions of the magnetic equator and ionization crests also played roles in the existence of ionospheric irregularities.     

Review and propositions for the sliding/impact wear behavior in a contact interface

A thermal-solid-liquid complex operational environment induces structural interface developing a typical coupling sliding/impact wear behavior. It results in contact damage until systems fail, which may cause significant economic losses and catastrophic consequences. The key point of solving this problem is to reveal the coupling damage mechanism of the sliding/impact behavior in typical systems and life characterization under a complicate evolving environment. This has been a hot topic in the area of mechanical reliability. The main work in this paper can be concluded as follows. Firstly, the main industries in which the “sliding/impact behavior” takes place have been introduced. Then, existing studies on the wear mechanism and degree analysis are presented, which includes surface morphology analysis, wear debris analysis, and wear degree measurement. Meanwhile, existing problems in theoretical modeling and experiments in current research are summarized, so as to point out a bright direction for future research on wear prediction. They include interface contact modeling, mathematic coupling mechanism modeling, wear equation establishment, and wear life characterization, which can provide some new ideas for improving the existing studies on the sliding/impact wear behavior.     

预测悬停旋翼跨音速流动的一种组合自由尾流/CFD方法

一种新的组合自由尾流 / CFD方法用于悬停旋翼流动的 CFD解中以考虑实际尾流的作用 .用文中描述的尾流分析方法研究了螺旋尖涡的运动 .首先从广义尾流模型开始 ,用半经验公式模化了涡核对旋翼尾流的作用 ;然后在环量收敛和尾迹收敛的条件下完成了自由尾迹计算 ;最后应用 Jameson有限体积龙格 -库塔推进格式求解了欧拉方程 .所得结果与相关文献和实验数据进行了比较     

K8、JK8机翼接头与检验量规协调准确度的提高

分析了 K8、 JL8机翼接头孔精加加后与检验量规位置协调的条件，介绍了为提高它们之间协调准确度所采取的措施及其效果。     

燃气的基准表及图制定

本文在阐述基准的热力学概念基础上,提出了燃气基准的计算方法,应用CHAPPELL推荐的有关燃气热力性质表达式,导出计算燃气基准的公式,通过微机计算,将结果整理成燃气基准的有关表、图。     

40Gb/s系统技术解决方案探讨

40Gh／8系统的应用面临光信号的色散、衰减、交换、编码等方面技术的挑战。利用固定补偿模块或源色散补偿技术可以实现光的精确色散及补偿。赖曼式放大器对40Gh／s系统的光传输提供了有力的技术支持，利用赖曼放大器以及全光交换机或光电光交换机则可以实现光信号的有效放大和高性能交换，而带外FEC技术和相应的编码技术可以进一步提高系统的容错能力及传输速率。     

黑体空腔不等温性对辐射温度计校准结果影响的计算分析

针对常用的圆柱型无盖黑体空腔,分别计算了在对工作波长为单波长(1μm,1.6μm)、波段(3~5)μm、(8~14)μm的辐射温度计进行校准时,由于空腔的不等温性引起的积分发射率变化对校准结果造成的辐射温度偏差。计算结果表明,黑体空腔实际存在的不等温性引起的辐射光谱偏离理想黑体辐射对校准结果造成的偏差是不容忽略的,对于每一个具体的黑体辐射空腔,都要对其不等温对校准结果的影响予以考虑。     

HML系统在商店偏好决策模型中的应用研究

对混合式机器学习系统（HML）进行了全面系统的介绍，并将其运用于服装消费商店偏好决策行为的研究中。采用上海统计局家庭调查网络，对300户家庭进行抽样分析后发现，服装消费商店偏好的主要影响因素是地区、季节、丈夫和妻子的学历、职业以及子女性别。在此基础上，将HML分析所得的结论与传统的研究方法和结果进行了系统比较：从方法上来看，因为属性变量包含间断变量和连续变量两种，因此传统统计分析要运用两种不同的检测方法对影响因素的相关性作出判断，结果需要经过统计学分析，才能得到结论；而HML分析结果比较直观和简单，便于理解。     

CAD/CAPP集成系统中工序图的自动生成方法

介绍了一种在CAD/CAPP集成系统中工序图自动生成的较通用的方法,提出了两种不同实现途径。并以实例表明在Pro/Engineer系统中得到了成功应用。