镀膜光纤声光相位调制器频率响应特性的研究

本文对光纤声光相位调制器（OF—AOPM）的频率特性进行研究。分析了OF—AOPM的调相原理，研究结果表明：在调制频率远离氧化锌压电薄膜的半波谐振频率的时候，光相位的调制不仅依靠径向应力。同时还依靠轴向应力。通过同时考虑径向和轴向应力的变化，得出了OF—AOPM在整个频率域范围内的响应特性。     

受轴向拉伸载荷作用的耳片强度研究

耳片是飞机结构的重要连接元件,是结构主要传力通道上的重要环节,是飞机结构强度计算和细节分析的重点部位。多年来,许多国内外学者、专家对其进行了大量试验研究工作。大量的试验表明,随着加载角度的增大,耳片的静拉伸破坏载荷降低,所以,现在在设计中,都尽量采用受轴向载荷的耳片。本文对受轴向拉伸载荷作用下的单、双耳片进行了强度分析研究,并进行了归纳总结。     

超长大直径钻孔灌注桩桩端承载力研究

阐述了超长大直径钻孔灌注桩桩端承载力的影响因素,包括施工工艺、深度效应和尺寸效应等。分析和对比了目前国内常用的各规范所采用的计算方法。文中算例的计算结果表明,对于同等条件的桩,各规范的计算结果相差较大。采用自平衡试桩法获得了几个重大工程的超长大直径钻孔灌注桩的桩端承载力的实测值。将工程实例的测试结果与各规范的计算结果进行对比,证实了目前规范的计算方法不尽合理。目前各规范中桩端承载力的计算方法是在针对小直径的中短桩的研究基础上建立的。如今,大型桥梁工程中普遍采用超长大直径钻孔灌注桩的情况下,对其桩端承载力的计算应当进行相应的调整,使设计更为合理。     

用测量法调节某型涡轮的轮背间隙

Cooling Turbine 204050是波音737飞机采用的一种涡轮冷却器,其传统的调节轮背间隙的方法操作繁琐、效率低下。本文介绍了一种测量法来调节204050的轮背间隙,该方法具有可靠性高、操作方便、效率高等优点。     

An equilibrium multi-objective optimum design for non-circular clearance hole of disk with discrete variables

An Equilibrium Multi-objective Optimization Model(EMOM) with self-regulated weighting factors has been proposed for the optimum design of non-circular clearance hole on the front flange of turbine disk. In the ‘‘equilibrium design", both the stress decrease around the hole and the least hole's profile variation are considered, which balances two ambivalent design goals. Specific discrete variables are applied to realize the standardization design in the optimization process, in which a Surrogate Genetic Coding Algorithm(SGCA) is introduced, and a special check module is used to get rid of repeated fitness evaluation of the samples. The method offers an equilibrium design for the non-circular clearance hole of the turbine disk with great accuracy and efficiency.     

跨声速串列转子失速机制的数值研究

为了解决跨声速串列转子的低裕度问题,就必须了解跨声速串列转子的流场结构与失速机制.设计了叶尖切线速度为450m/s,负荷系数为0.56的高负荷跨声速串列转子.基于数值模拟的结果,分析了该串列转子在0.5mm叶尖间隙下的叶尖流场结构与失速机制,并在此基础上分别探讨了叶尖间隙和前、后排叶片周向位置对串列转子特性的影响和失速机制的变化.结果表明:前排叶片的叶尖区域是 影响串列转子稳定性的关键;随着叶尖间隙的增加,串列转子的失速机制也发生变化,从前排叶片叶尖区域的尾迹与径向潜流堵塞后排叶片通道转变为前排叶片叶尖泄漏流堵塞;在较大周向相对位置(后排叶片压力面周向远离前排吸力面)的情况下,串列转子获得最好的效果,随着周向相对位置(PP)的增加,失速部位从后排叶片转移至前排叶片.      

蜂窝式轴心通风器油气分离性能计算

为对航空发动机蜂窝式轴心通风器油气分离效率进行研究,建立考虑油气双向耦合的流场计算方法及油滴/壁面相互作用模型,在验证通风阻力及油气分离效率可靠性的基础上,对不同转速、通风流量和环境温度下蜂窝式轴心通风器的油气分离效果进行计算和分析.结果表明:转速的增加会使油气分离效率得到提升,而通风流量和环境温度的增加则导致油气分离效率的降低.蜂窝孔结构的加入对通风阻力影响不大,却对通风器的滑油分离过程起主要作用,计算表明其对滑油分离贡献率在80%以上.      

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

端壁造型技术在亚声轴流压气机级中的应用

为探索利用端壁造型技术来提高轴流压气机性能的可能性,以亚声轴流压气机试验级为对象,对端壁造型技术在压气机中的应用进行了研究.鉴于压气机的逆压工作环境,端壁设计结合了周向(非轴对称)和流向两个方向的造型,具体介绍了造型方法.对端壁造型后压气机级的数值模拟显示:端壁造型技术可以有效减小、消除静子角区分离,进而提高级的效率和压比.      

轴流压气机动态失速过程三维计算

基于三维非定常欧拉方程和三维激盘模型发展了一种用于研究轴流压气机动态失速过程的三维计算方法.利用该计算方法研究了某型高压压气机第一级的动态失速过程,并就转子总静压升特性的三种不同径向分布对失速过程的影响进行了分析.计算结果表明该方法能够反映出压气机的三维动态失速过程、失速团的三维空间结构,并能有效地表现出转子沿径向的特性变化对压气机气动稳定性的影响,而且还能够用于判断压气机的危险截面.