Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

A multi-stage regulation strategy of space manipulators with a free-swinging joint failure

To ensure tasks can be completed after a free-swinging joint failure occurs, a multi-stage regulation strategy of space manipulators is proposed. Considering all terms of the dynamics equation, an evaluation model of the regulation ability (EMRA) of active joints over the fault joint is established based on the fuzzy entropy. And then a multi-stage regulation strategy based on the EMRA is designed to regulate the fault joint. The strategy divides the regulation process into several stages, and select a certain active joint to regulative the fault joint in every stage. With this multi-stage regulation strategy, the fault joint can be regulated to the desired angle without huge torque on regulative joints. The simulation is carried out with a 7-DOF space manipulator, verifying the correctness and effectiveness of the multi-stage regulation strategy. The strategy has three advantages: Coriolis and centrifugal terms are both considered for the first time in selecting the regulative joint, making the selection result more in line with the actual regulation process; The influence of the model uncertainty is eliminated in establishing the EMRA, making the evaluation of regulative ability more precise; The fault joint is successfully regulated to the desired angle without huge torque on regulative joints.     

K8、JK8机翼接头与检验量规协调准确度的提高

分析了 K8、 JL8机翼接头孔精加加后与检验量规位置协调的条件，介绍了为提高它们之间协调准确度所采取的措施及其效果。     

中心极限定理用于近似计算时必须注意的问题

本文着重指出,在运用中心极限定理近似计算独立同泊松分布随机变量之和的概率时,通常只注意了取n适当大的值,从而导致了差异较大的不同结果。本文指出了不仅要使n适当的大,而且也要使nλ足够地大。当X_h是其他离散型随机变量时,也要考虑类似的问题。     

适用于含多个隐式极限状态方程的飞机结构系统安全分析新方法

工程复杂随机结构的概率安全分析中，最重要的两个步骤是建立所有失效模式的极限状态方程和计算所建立极限状态方程的失效概率。一般来说大型复杂工程结构的极限状态方程都是隐式的，且当材料参数、结构参数和外载荷等均为随机变量时，极限状态方程均为非线性的，为此文中提出了建立真实复杂结构多模式隐式极限方程的等效方法。该方法对于单个极限状态方程采用在均值点展开成线性项和高次项修正的方式，在概率等效的基础上，建立起原非线性隐式极限状态方程的概率等效线性显式极限状态方程。当结构系统所有极限状态方程都建立了其等效显式线性极限状态方程后，即可利用可得的可靠性分析方法来计算结构系统的等效失效概率。所提方法被用于真实飞机结构翼身连接接头的强度刚度多模式可靠性分析，与迭代响应面法计算结果的对比表明，所提方法具有较高的精度。并且所提方法可以与任何标准有限元程序相结合，而标准有限元程序是当今处理结构力学分析与设计的强有力的工具，文中方法提供了力学分析与概率安全分析相结合的合理连接，其应用前景将是十分广泛的。     

正态模型结构可靠性贝叶斯下限的计算方法

本文对正态模型结构可靠度的贝叶斯精确下限的评估公式提供一种新的计算方法。该方法能达到任意给定的精度。计算复杂度可由O(n~2)降为O(n)。程序结构简单,使用方便。     

带滑移铰空间机械臂惯性空间轨迹的复合自适应跟踪控制

讨论了载体的位置与姿态均不受控制的漂浮基带滑移铰空间机械臂的控制问题。动力学分析表明，结合系统动量及动量矩守恒关系得到的运动Jacobi关系及系统动力学方程将是系统惯性参数的非线性函数，借助于增广变量法，我们得到了与惯性参数呈线性关系的系统广义Jacobi矩阵及系统控制方程，以此为基础，针对系统中存在未知惯性参数的情况，设计了一种末端抓手惯性空间期望轨迹跟踪的复合自适应控制方案，此控制方案的优点在于不需要测量空间机械臂载体的位置及移动的速度，加速度，仿真运算证实了方法的有效性。     

防止Ⅱ型驾驶员诱发振荡技术的研究

许多严重的飞行事故都与由速率限制引起的Ⅱ型PIO有关。针对如何预防PIO，首先介绍了自适应杆增益和软件限制环节的设计原理。然后以某带速率限制的电传飞机为例，运用同一理论，分析采用自适应杆增益和软件限制环节来改善速率限制的不利影响。仿真结果表明，自适应杆增益环节和软件限制环节都能抑制住PIO的发生，但两者组合加入抑制效果更好，飞行品质也能达到满意的程度。     

建设工程项目工期优化分析

分析了传统的工期优化方法存在的不足，考虑建设项目提前投产的经济效益、缩短工期减少承包商固定资产占用带来的效益、缩短工期减少投资项目的固定资产及流动资金的上用时给业主带来的资金时间价值等因素，建立了工期优化的理论模型，与传统的工期——成本优化方法进行了比较分析，并给出了实用的优化方法。     

微机符号解析系统的研制和其用例

 参照REDUCE系统,在PC微机上,建立了一个用于非数值处理的符号解析系统和语言。本系统具有较为完备的系统控制功能与错误处理能力,允许作业嵌套,并可随时打断作业的运行。窗口和功能键的设置为使用者提供了很大的方便。最后,给出两个非数值用例。