Unsteady wakes-secondary flow interactions in a high-lift low-pressure turbine cascade

Detailed experimental measurements were conducted to study the interactions between incoming wakes and endwall secondary flow in a high-lift Low-Pressure Turbine (LPT) cascade. All of the measurements were conducted in both the presence and absence of incoming wakes, and numerical analysis was performed to elucidate the flow mechanism. With increasing Reynolds number, the influence of the incoming wakes on suppressing the secondary flow gradually increased owing to the greater influence of incoming wakes on reducing the negative incidence angle at higher Reynolds numbers, leading to a lower blade loading near the leading edge and suppression of the Pressure Side (PS) leg of the horseshoe vortex. However, the effect of unsteady wakes on suppressing the profile losses gradually became weaker owing to the reduced size of the Suction Side (SS) separation bubble and increased mixing loss in the free-flow region at high Reynolds numbers. Incoming wakes clearly improved the aerodynamic performance of the low-pressure turbine cascade at low Reynolds numbers of 25,000 and 50,000. In contrast, at the high Reynolds number of 100,000, the profile loss at the midspan and mass-averaged total losses downstream of the cascade were higher in the presence of wakes than in the absence of wakes, and the unsteady wakes exerted a negative influence on the aerodynamic performance of the LPT cascade.     

简易U型弯曲模设计

本文介绍了一种简易的u型弯曲模具的设计方法,具有结构简单、制造容易、节约材料、重量轻的特点,在小批量生产中有借鉴意义.     

复合材料梁的热弯实验

为研制先进的导弹弹翼，用新研制的复合材料制成工字梁，模拟导弹飞行时翼梁受热弯条件进行实验，测出梁的温度和挠度随时间变化曲线，确定正常使用条件和失效形式，用此复合材料代替现役导弹的金属材料，可明显减重，改善性能。     

钛合金板材激光弯曲成形的研究

 对常温下钛合金板材进行了激光弯曲成形研究。分析了激光功率、扫描速度、光斑大小对板材弯曲变形的影响,获得理想工艺参数范围为:功率1 .0～1 .2 k W、扫描速度2～3 m/min、光斑直径6～7mm。同时分析了板材厚度、宽度及扫描次数对材料弯曲变形的影响,为钛合金板材弯曲成形提供了一种新途径。     

固冲发动机补燃室流场的实验校测

1引言目前数值模拟已广泛应用到火箭发动机的流场分析中,特别是固冲发动机补燃室的燃烧和流动[1,2]。但是这种方法在固冲发动机补燃室应用的有效性还没有合适的实验验证。国外开展的补燃室流动实验大多以水为介质,用片光流动显示的方法观察流场的概貌,与真实发动机的流动之间存     

吸力面翼刀对压气机叶栅内二次流的影响

1引言在叶轮机械叶栅内流动控制中,可以通过在叶片吸力面、端壁上安装翼刀或隔片,控制二次流的发展,降低二次流损失,其中将翼刀加装在吸力面上的控制方式即为吸力面翼刀控制技术。吸力面翼刀主要是通过阻断端壁附面层和叶片吸力面附面层近端壁处低能流动沿吸力面的展向迁移来对     

Experimental investigation on silica dust lofting due to charging within micro-cavities and surface electric field in the vacuum chamber

The charged dust particles can be mobilized electrostatically by the repulsion between the adjacent grains and the surface electric field due to the incoming electron current and the charge accumulation within the micro-cavities. In this study, the experimental results of the initial vertical launching velocities and the maximum dust heights are compared with the estimated values for the lofted spherical dust grains by the patch surface charging equations. Silica particles with the sizes between <6 and 45?µm in radius are loaded on a graphite plate, and they are exposed to the electron beam with 450?eV energy under 4?×?10^?3?Pa vacuum chamber pressure. During the first set of the experiments, the dust samples are tested without an initial compression process and an additional horizontal electric field. Second, the dust samples are compressed by two different weights in order to increase the packing density under approximately 780.7?Pa and 3780?Pa. Finally, the dust grains are placed between the two parallel aluminum plates to apply approximately 2000?V/m and 4800?V/m horizontal electric field. A high-speed camera is used to record the transportation of the dust grains together with a microscopic telescope, and the results point out that the patch surface dust-charging model estimations are in agreement with the first experiments. On the other hand, the dust particles from the compressed samples are lofted with higher velocities than the estimations, and the number of the dust lofting observations decreases significantly, which demonstrates the importance of the micro-cavities and the increased charging requirement to overcome the contact forces. When the horizontal electric field is present, the initial vertical launching velocities are measured to be lower than the other experiments, which can be attributed to the decreased charging requirement for the dust lofting as a result of inter-particle collisions and rolling motion. According to the experimental results, the electrostatic dust transportation can be controlled not only by the ambient plasma and the solar irradiation on the airless planetary bodies, but also by the surface properties such as the contact surfaces between the dust grains, the number of the micro-cavities related to the packing density, and the presence of the horizontal electric field contributing to the external forces by other particle motions.     

利用小尺寸缺口试样测定延性材料的单轴本构关系

提出了一种利用三点弯曲试样获取延性材料本构关系的测试方法：针对小尺寸缺口试样的三点弯曲线载荷-位移曲线,采用有限元辅助测试（Finite-element-analysis aided tests,FAT）方法,迭代获得材料代表性体积单元（Representative volume element,RVE）本构关系。研究表明,两种延性材料的有限元迭代反求结果和单轴拉伸试验结果吻合较好。应用该方法,可以采用小尺寸缺口试样来获取延性材料的本构关系。     

基于自适应网格的超声速液体射流破碎过程研究

为研究超声速气流中液体横向射流的破碎过程,采用脉冲背景光方法和VOF方法开展了实验和数值研究。为提高液体横向射流中气液界面和气流场特征捕捉的精确性,采用自适应网格技术对于气液界面、激波出现位置进行网格细化,计算得到了较为精细的气液界面、激波特征及涡系结构。研究结果表明:在低成本仿真模拟条件下,利用自适应网格计算得到的射流轨迹和轮廓与实验吻合较好,射流轨迹的最大误差为10%;射流初始段在超声速气流条件下,仍然存在一段高度约为1.9倍喷孔直径且圆柱形态保持较好的连续光滑液柱。随着喷注压降的升高,液柱的长度逐渐增大;主流气体流经液柱发生三维绕流,在射流附近和近壁面区域形成不断演化的反转涡对,反转涡对的形成加速了液体射流一次破碎过程。     

Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected.