The development of a Russian communication satellite of small class, operating in the geostationary and high-elliptical orbits

In 1994-1995 Lavochkin Association (Russia) together with the other enterprises in accordance with technical requirements of the Russian Space agency, developed a new Russian communication satellite of a small class that will operate in both the geostationary (GSO) and high-elliptical (HEO) orbits. This satellite may be injected into operational orbits using a SOYUZ-2 launch vehicle (LV) and a FREGAT upper stage (US) from Plesetsk and Baykonur space launch sites (SLS).The main reason for creating such a satellite was to decrease the cost of the support and development of the Russian communication geostationary satellites group.Russian satellites Horizont, Express, Ekran and Gals, which operate in GSO, are the basis of the space segment for communications, radio and TV broadcasting. All of these satellites are injected into GSO by the PROTON LV. PROTON is a launch vehicle of a heavy class. The use of a middle class LV instead of a heavy class will allow to reduce considerably the launch cost. The change of a heavy class LV to a LV of middle class determined one economic reason for this project. Besides, the opportunity to launch S/C into GSO from Russian Plesetsk SLS increases the independence of Russia in the domain of space communications, despite the presence of the contract with Kazachstan about the rent of Baykonur SLS. Finally, use of small satellites with a rather small number of transponders is more effective than the use of big satellites. It will allow also to increase a satellite group (by the launch of additional satellites) precisely in accordance to the development of the ground segment.     

应答式目标旋转运动对雷达速度测量的影响

携带应答机的飞行目标,若除了沿其某一轨道运动外,还作自旋运动,应答机天线辐射相位空间分布的不均匀性会使应答机转发信号产生附加的相位调制,因而导致多卜勒测量雷达的测量误差。本文分析了对称安装三天线园柱形应答式目标回波的多卜勒频率调制。得出了附加多卜勒频率及其各阶导数的解析式。研究了目标旋转速度、方向角(目标旋转轴线与雷达视线的夹角)和回波谱线宽度的关系,以及对雷达多卜勒测量精度的影响,它对于研究自旋再入体测量问题具有实用价值。文章给出了一个典型的三天线园锥目标模拟旋转试验结果。试验中在不同目标转速下由相参雷达跟踪测量目标回波,同时记录中频信号、多卜勒跟踪回路鉴频器输出等有用信息。对试验数据的分析得出了明确的结论:目标旋转使回波信号的谱线展宽、测速误差增大,谱线宽度与目标转速成正比,同时谱线宽度随目标方向角增大而加宽,方向角为90°时旋转影响最大。理论分析得出了与试验相同的结果。虽然试验是在静态下进行的,但问题的分析对质心运动的目标也同样适用。     

机动再入飞行器自适应飞行控制系统设计

研究机动再入飞行器的制导控制问题。为了解决机动再入飞行器气动系数变化范围大、气动耦合严重和气动参数非线性过零常值大等恶劣条件下的控制，并且能充分利用飞行器可测量信息提高系统自适应能力，本文提出了状态方程参数辨识－－极点配置－－前馈补偿自适应控制的飞行控制系统的设计方法。通过对新型号再入飞行器的制导系统仿真，可以看出该控制系统使其有很好的飞行性能。     

机动再入飞行器的复合制导方案研究

对机动再入飞行器弧段的复合制导方案进行了研究，首先提出了通过高低空复合制导控制再入飞行器的终端速度和弹道倾角的思路；然后分别给出了高空最优制导律和大气厚再入最优制导律；最后对此复合制导方案进行了数字仿真。仿真结果表明此方案在理论上是可行的。     

再入制导和弹道跟踪误差分析

新一代可重复使用运载器对再入制导提出了更高地要求。目前的空间运输系统证明基于阻力加速度的制导方法是行之有效的。其基本概念是跟踪基准阻力加速度包线，在飞行过程中可根据需要更新这个包线。跟踪适当的阻力加速度包线保证了飞行器可以飞行准确的距离达到目标，同时满足弹道约束。在横向上，我们可采用类似于美国航天飞机的倾斜反转逻辑或航向角跟踪技术。本文推导出了基于反馈线性化的控制算法，并将其应用于可重复使用运载器纵向和横向的制导。最后，我们分析了阻力加速度跟踪的误差。     

航天器最优再入轨迹的选择分析

本文研究的目的是想获得具有最大有效载荷的航天器最优再入轨迹。返回段航天器的最大有效载荷等价于航天器离轨点所耗燃料质量与热防护系统（ＴＰＳ）质量之和达极小。文中把最大有效载荷的再入轨迹分三种情况作了分析：航天器ＴＰＳ质量不确定时，通过返回轨迹优化来获得航天器的最大有效载荷，并选择确定相应ＴＰＳ的质量；ＴＰＳ质量已确定时，通过再入轨迹优化来获得航天器的最大有效载荷；ＴＰＳ质量足够大时，通过多次穿越大气层来获得航天器的最大有效载荷。本文的结论可为航天器再入轨迹与ＴＰＳ的一体化选择提供思路。     

再入体激波层和近尾流热辐射实验研究

本文介绍了在弹道靶设备上对再入速度下模型的热辐射进行的实验研究工作。铝、高硅氧和聚碳酸酯三种材料的模型在速度为4.5～6.0(km/s),压力为600—8000Pa条件下做了实验,在258nm—1100nm光谱范围内完成了九个波段的辐射测量,给出了三种材料模型的辐射光谱分布曲线。结果表明辐射量除了受环境条件影响外,还强烈地依赖于模型材料;由烧蚀产物引起的辐射通量主要在可见光和近红外区(465nm以上)。估算了烧蚀产物引起的辐射加热率,对头部和近尾流辐射通量做了比较。     

再入飞行器优化气动布局研究

本文研究了再入飞行器的优化气动布局问题，提出了单目标和多目标、优化设计方法。通过研究分析，指出了具有高机动性能的带翼机动再入飞行器、弯体机动再入飞行器及带翼锥柱裙机动再入飞行器等再入飞行器的几何参数变化规律。该研究对这类再入飞行器的气动布局选型有重要的参考价值。     

高空高速无人飞行器热控制系统设计

针对飞行时间短、速度和高度变化快、表面温度波动大的无人飞行器UAV(Unmanned Aerial Vehicles)热控制系统设计难题,提出了一种可解决实际工程问题的热分析计算方法.即把热天工况、冷天工况和标准天工况作为设计/试验工况;采用参考温度法、高超音速工程预测法或计算流体动力学CFD(Computational Fluid Dynamics)数值模拟法,确定了飞行器表面温度分布,并把其作为后续热分析数学模型的外边界条件;分析结构热容量对瞬态热载荷的影响,建立与之相应的边值问题方程,并采用有限差分法求解;根据高空高速飞行特点及瞬态热载荷值,确定仪器设备舱调温系统方案.     

Modeling novel methodologies for unmanned aerial systems–Applications to the UAS-S4 Ehecatl and the UAS-S45 Bálaam

The rising demand for Unmanned Aerial Systems(UASs) to perform tasks in hostile environments has emphasized the need for their simulation models for the preliminary evaluations of their missions. The efficiency of the UAS model is directly related to its capacity to estimate its flight dynamics with minimum computational resources. The literature describes several techniques to estimate accurate aircraft flight dynamics. Most of them are based on system identification. This paper presents an alternative methodology to obtain complete model of the S4 and S45 unmanned aerial systems. The UAS-S4 and the UAS-S45 models were divided into four sub-models, each corresponding to a specific discipline: aerodynamics, propulsion, mass and inertia, and actuator. The‘‘aerodynamic" sub-model was built using the Fderivatives in-house code, which is an improvement of the classical DATCOM procedure. The ‘‘propulsion" sub-model was obtained by coupling a two-stroke engine model based on the ideal Otto cycle and a Blade Element Theory(BET) analysis of the propeller. The ‘‘mass and the inertia" sub-model was designed utilizing the Raymer and DATCOM methodologies. A sub-model of an actuator using servomotor characteristics was employed to complete the model. The total model was then checked by validation of each submodel with numerical and experimental data. The results indicate that the obtained model was accurate and could be used to design a flight simulator.