Application of improved active disturbance rejection control algorithm in tilt quad rotor

The Tilt Quad Rotor (TQR) has complex dynamics characteristics, especially in conversion mode. It is difficult to build the dynamic model of the TQR and the environmental factors have a great influence on it. To solve the problem of control in conversion mode of TQR, this paper carries out the design of the controller based on improved Active Disturbance Rejection Control (ADRC). According to the characteristics of flight in conversion mode, Tracking Differentiator (TD) with explicit model is used to solve the problem of multiple integrals when the system is high-order system. Extended State Observer (ESO) with Radial Basis Function (RBF) neural network is used to estimate and compensate for internal and external uncertainties, and the adaptive sliding mode control in Nonlinear State Error Feedback (NLSEF) is used to improve the response speed of the controller and reduce the parameters which should be tuned. Through the flight control simulation of the TQR, the validity and rationality of the control system are verified.     

基于虚拟正交试验的压气机叶轮轴-毂径向微动特性研究

用Pro/E建立压气机叶轮轴-毂三维模型,利用ANSYS软件采用子结构结合网格随移技术的分析方法,建立其有限元模型。采用虚拟正交试验方法对压气机叶轮轴-毂进行仿真,得出过盈量、摩擦系数、转速对最大单位摩擦功和平均摩擦功影响显著性次序及影响规律,得到最优组合。结果表明,模拟及正交试验优化结果准确、可靠,有效地降低了摩擦磨损程度,对实际装配过程具有一定的指导作用。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Practical compensation for nonlinear dynamic thrust measurement system

The real dynamic thrust measurement system usually tends to be nonlinear due to the complex characteristics of the rig, pipes connection, etc. For a real dynamic measuring system,the nonlinearity must be eliminated by some adequate methods. In this paper, a nonlinear model of dynamic thrust measurement system is established by using radial basis function neural network(RBF-NN), where a novel multi-step force generator is designed to stimulate the nonlinearity of the system, and a practical compensation method for the measurement system using left inverse model is proposed. Left inverse model can be considered as a perfect dynamic compensation of the dynamic thrust measurement system, and in practice, it can be approximated by RBF-NN based on least mean square(LMS) algorithms. Different weights are set for producing the multi-step force, which is the ideal input signal of the nonlinear dynamic thrust measurement system. The validity of the compensation method depends on the engine’s performance and the tolerance error0.5%, which is commonly demanded in engineering. Results from simulations and experiments show that the practical compensation using left inverse model based on RBF-NN in dynamic thrust measuring system can yield high tracking accuracy than the conventional methods.     

基于RBF带学习能力高精度非线性FDD设计

在轨航天器故障检测与诊断问题需要面对模型的非线性,而且要求尽量提高其检测的精度,为此设计了基于径向基函数（RBF）神经网络的动量轮非线性故障检测与诊断（FDD）方案。首先应用RBF补偿建模误差,提高检测精度,并选择李雅普诺夫函数证明其收敛性;然后应用非线性观测器来产生故障残差,给出了阈值以及故障检测的时间;应用RBF网络对故障信号进行重构,并据此设计了带学习能力的FDD策略。再次建立了详细的动量轮模型,通过不同条件下的仿真研究分别验证残差的阈值特性、时间特性以及RBF的重构能力,仿真结果表明了算法的有效性。     

UV镜对摄影测量精度的影响及消除方法研究

针对摄影测量中加入UV镜后对测量结果的影响问题进行了研究。通过理论推导UV镜对于像点坐标偏移的影响,得出UV镜对像点偏移的影响规律,并提出采用自检校光束法平差的方法消除UV镜对像点偏移的影响,实验证明本文得出的对UV镜产生的像点偏移规律的分析及解决方法都是正确的。     

Using the radial basis function neural network to predict ionospheric critical frequency of F2 layer over Wuhan

Neural networks (NNs) have been applied to ionospheric predictions recently. This paper uses radial basis function neural network (RBF-NN) to forecast hourly values of the ionospheric F₂ layer critical frequency(f_oF₂), over Wuhan (30.5N, 114.3E), China. The false nearest neighbor method is used to determine the embedding dimension, and the principal component analysis (PCA) is used to reduce noise and dimension. The whole study is based on a sample of about 26,000 observations of f_oF₂ with 1-h time resolution, derived during the period from January 1981 to December 1983. The performance of RBF-NN is estimated by calculating the normalized root-mean-squared (NRMSE) error, and its results show that short-term predictions of f_oF₂ are improved.     

A statistical study of C IV regions in 20 Oe-stars

In this paper, using the Gauss-Rotation model (GR model), we analyse the UV C IV resonance lines in the spectra of 20 Oe-stars of different spectral subtypes, in order to detect the structure of C IV region. We study the presence and behavior of absorption clouds and analyse their characteristics. From this analysis we can calculate the values of a group of physical parameters, such as the apparent rotational and radial velocities, the random velocities of the thermal motions of the ions, the Full Width at Half Maximum (FWHM), the optical depth, as well as the absorbed energy and the column density of the independent regions of matter, which produce the main and the satellite clouds of the studied spectral lines. Finally, we present the relations between these physical parameters and the spectral subtypes of the studied stars and we give our results about the structure of the C IV region in their atmosphere.     

Effect of protrusion amount on gas ingestion of radial rim seal

In this paper, the effect of different amount of protrusion on various parameters in rotor–stator system was experimentally studied by measuring CO₂ concentration and pressure, in order to obtain the optimal protrusion amount. The parameters of different dimensionless sealing flow were measured under the condition that the annulus Reynolds number was 4.39 × 10⁵ and the rotating Reynolds number was 1.05 × 10⁶. The results show that the change of the amount of protrusions has little effect on the static pressure in the cavity, and the static pressure change near the sealing ring is almost negligible. But the total pressure and sealing efficiency increase first and then decrease with the increase of the amount of protrusion. The variation of power consumption is the same. A complex vortex structure will appear at the high radius region when the protrusion is installed. On the other hand, the protrusion can effectively reduce the minimum sealing flow of the rotor–stator cavity. Furthermore, considering the sealing efficiency and power consumption, the best range of the protrusion amount is about 36. The ratio near this range can optimally balance the alleviation of the gas ingestion and the reduction of the power consumption.     

环下润滑结构对径向收油环收油效率影响的数值计算研究

为研究环下供油润滑系统中的流动过程和收油环收油效率的影响因素及其影响规律,基于VOF(Volume of fluid)两相流模型和滑移网格模型的数值计算方法,建立了环下润滑系统内部流场的计算模型。通过数值计算,获得了收油环的收油效率并验证了数值计算结果的有效性,分析和探讨了不同结构参数对收油效率的影响。计算结果表明:利用本文数值计算方法得到的收油效率和流动现象与已有实验和数值计算结果均一致;供油喷嘴角度和收油环外径均主要影响滑油射流冲击收油叶片的飞溅量和收油叶片切割滑油量,收油效率取决于二者的相对大小,θ=0°,θ=9°和r0=2mm,r0=6mm时收油效率取极大值;收油叶片数量和供油喷嘴与收油叶片间距离分别影响收油叶片切割滑油射流的时间间隔和滑油射流在到达收油叶片前的流动,不影响滑油射流冲击收油叶片的飞溅量和收油叶片切割滑油射流的量,对收油效率的影响较小。