Multi-faults diagnosis of rolling bearings via adaptive customization of flexible analytical wavelet bases

Multi-faults detection is a challenge for rolling bearings due to the mode mixture and coupling of multiple fault features, as well as its easy burying in the complex, non-stationary structural vibrations and strong background noises. In this paper, a method based on the flexible analytical wavelet transform (FAWT) possessing fractional scaling and translation factors is proposed to identify multiple faults occurred in different components of rolling bearings. During the route of the proposed method, the proper FAWT bases are constructed via genetic optimization algorithm (GA) based on maximizing the spectral correlated kurtosis (SCK) which is firstly presented and proved to be efficient and effective in indicating interested fault mode. Via using the customized FAWT bases for each interested fault mode, the original vibration measurements are decomposed into fine frequency subbands, and the sensitive subband which enhances the signal-to-noise ratio (SNR) is selected to exhibit the fault signature on its envelope spectrum. The proposed method is tested via simulated signals, and applied to analyze the experimental vibration measurements from the running roller bearings subjected to outrace, inner-race and roller defects. The analysis results validate the effectiveness of the proposed method in identifying multi-faults occurred in different components of rolling bearings.     

组网数据处理探讨

讨论了测向定位中双站交会定位及定位误差分析、三站交会定位、多站交会定位若干问题，首次尝试将最小二乘法和递推最小二乘法用于多站测向定位，减少了大量的矩阵求逆，数据利用效率高，可以提高测向定位的精度和简化运算。特别是在存在多径效应的情况下，有利于发现和去除野值。在测向站组网数据的处理和应用上有较强的实用性和推广价值。     

Estimation of sea surface temperature, wind speed and water vapor with microwave radiometer data based on simulated annealing

A method for estimation of sea surface temperature, ocean wind speed and water vapor with microwave radiometer data based on simulated annealing is proposed. The proposed method shows about 60% improvement of sea surface temperature estimation accuracy in comparison to the existing method using Newton’s iterative algorithm.     

太阳风质子束流的演化

太阳神飞船观测表明，太阳风高速流中质子束分量相对于核分量的密度随日心距离增加而增加．提出解释这一观测现象的机理并给出二维数值模拟结果．由于阿尔芬波速随日心距离增加而减少，第二支左旋波将与更多的质子共振，把部分原来属于核分布的质子拉到束分布中来．用数值模拟方程方法求解回旋波共振导致的准线性扩散方程，数值结果与观测结果相符合．     

聚焦脉冲激光大气传输热晕效应的数值分析

利用激光大气传输四维程序对序列脉冲激光大气传输热晕效应进行了数值计算和分析。对于均匀大气路径上聚焦传输序列脉冲激光进行数值仿真计算得到,风场渡越时间内的脉冲数Np在2~6之间有利于传输;然后对实际大气模式下序列脉冲激光进行了数值计算,得到的平均脉冲数-NP可以在一定条件下对序列脉冲激光进行定量表征的结论。     

结构的斜撑杆布局与优化分析

应用组合理论，通过改变六面体刚架结构面上的斜撑杆添加方向获得布局不同的模型，并采用有限元方法对相应的结构进行了静力分析和固有频率分析，对部分模型进行了静力实验。结果表明：不同斜撑杆布局结构的抗扭性能有明显变化，合理的布局不仅明显提高了结构的抗扭刚度，也降低了扭转工况下的应力水平；但布局的变化对结构的固有频率影响不明显。     

时效处理对T-250钢电子束焊接接头组织及性能的影响

采用金相显微镜、透射电镜观察了焊后不同时效状态下T— 2 5 0马氏体时效钢电子束焊缝的微观组织 ,测试了不同时效状态下焊接接头的室温强度、夏比缺口冲击韧性、显微硬度 ,并用扫描电镜分析了拉伸断口形貌。结果表明 :随时效温度的升高 ,焊缝区枝晶间逆转奥氏体析出量增加 ,焊缝缺口冲击韧性增大 ,断口韧窝增大 ;但由于 5 0 0℃× 4h时效处理后焊缝马氏体孪晶较多而使其拉伸强度和缺口冲击韧性降低。经 4 80℃× 4h时效处理后 ,焊接接头强度具有最佳强韧性配合     

悬臂空心梁式加速度计的设计

分析证明:悬臂梁式加速度计的灵敏度与它的谐振频率的平方成反比。因此,欲展宽频带而保持灵敏度不变就很困难。利用应力集中的方法可以有效地解决这一问题。采用空心梁结构不仅能产生应力集中而且能减少梁的自身质量带来的影响,可以有效地展宽频带。文中给出了几种梁的刚度计算。     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

磁选态单束铯束管束光学参数的模拟计算和设计

为提高铯束管跃迁信号强度,在束光学参数设计中,用蒙特卡罗方法模拟计算铯原子通过率和未跃迁比例。通过改变模拟计算中的束光学参数,分析铯原子通过率、未跃迁比例和倍增器首极电流的变化趋势,得到了主要束光学参数的合理取值范围。在铯束管实际装配和试验中使用束光学参数设计结果,有效地增加了倍增器首极电流。