Digital Aircraft Sheet Metal Part Manufacturing System and Its Key Technology

The architecture of digital sheet metal manufacturing system is proposed based on the classification of sheet metal manufacturing information.The essence of digital manufacturing is the definition,management and transfer of information,and the key technologies are brought forward and described.It is pointed out that knowledge-based manufacturing elements design is necessary to make digital technology efficient.The management of all kinds of sheet metal manufacturing element information is to build single source of manufacturing data.Multi-state model-based digital transfer and coordination method is designed to provide a foundation for digital manufacturing of aircraft sheet metal part.The application of digital sheet metal manufacturing is exemplified with an aircraft sheet metal part.The application result is compared to that of the traditional analog transfer technology.It is shown that the developed technology can improve part quality,shorten manufacturing time and lower manufacturing cost.     

金属膜片贮箱膜片变形的数值模拟与失效分析

根据弹塑性有限变形理论，用有限元法建立了卫星推进系统贮箱金属膜片变形的有限元分析模型。在一定条件下，模拟了贮箱金属膜片的变形翻转过程，分析其翻转的特点，以及变形过程中表面压力、顶点径向位移和卷边处应力的变化，并给出了膜片失效原因。研究表明，数值模拟与试验结果较为吻合，所建分析模型合理。     

离心加速声中液态浸渗纤维预制体动力学分析

在将纤维预制体视为“毛细管束”的基础上,采用达西定律建立了离心加速场中金属液浸渗纤维预制体的浸渗动力学模型。采用该模型分析了离心加速场中金属液浸渗纤维预制体的临界转速,考察了金属液浅注量、设备转速、铸件高度、金属液原如外半径以及纤维预制体孔隙率对离心加速场中金属 浸润纤维预制体的影响。结果表明,金属液浸润纤维预制体的临界转速只与临界压力、金属液的浇注量、铸件高度以及纤维预制休性质有关;增加金属液浇注量、设备转速及金属液原始外半径,降低铸件高度、预制体纤维体积分数,有利于金属液的浸渗。     

用非线性有限元法分析金属基复合材料的叠层板壳

采用通用于复合材料叠层厚、薄板壳的Ｈｅｆｅｒｏｓｉｓ三维退化曲壳元，利用Ｈｉｌｌ屈服准则和层状模型法，对金属基复合材料叠层板壳进行了弹塑性分析。算例结果表明，所用方法是可靠的，精度良好。     

固体燃料冲压发动机硼燃料的燃烧

本文介绍了固体燃料冲压发动机(SFRJ)中硼燃烧的特点及改善燃烧效率的一些措施.     

轻金属颗粒燃烧理论研究进展

介绍了铝、镁和铍一类轻金属颗粒在氧化氛围中燃烧的有关实验现象，并在此基础上对蒸气相扩散机理、多相机理及复合机理进行了述评。     

金属水反应水冲压发动机系统性能估算

使用金属／水反应燃料是推进水下超高速航行器的最佳途径，分析了单次注水和二次注水的铝／水反应燃料水冲压发动机系统，得出了燃料质量配比、燃烧室温度、燃烧室压强、系统有效推力、效率等关键技术性能指标。指出了二次注水系统的优越性并提出了一种二次注水系统的实施方案。分析结论与实际系统性能指标相吻合，证明了分析的正确性，可以为系统研究提供参考。     

铸造SiCp／ZL101复合材料的组织与性能

本文利用半固态搅拌铸造法制备了ＳｉＣｐ／ＺＬ１０１复合材料，对其组织和某些性能进行了研究，结果表明：ＳｉＣｐ在基体中分布均匀，无严重团聚现象，与基体结合良好，与基体合金相比，耐磨性，硬度有显著提高。     

低温度系数标准电阻器的研制

主要介绍了低温度系数标准电阻器的研制,包括采用的电阻合金材料、电阻合金材料的筛选、匹配与加工制作,低温度系数标准电阻器的技术参数、温度系数测量方法,减小温度系数采用的补偿方法,测试结果分析。     

Influence of TiB2 particles on machinability and machining parameter optimization of TiB2/Al MMCs

In situ formed TiB₂ particle reinforced aluminum matrix composites (TiB₂/Al MMCs) have some extraordinary properties which make them be a promising material for high performance aero-engine blade. Due to the influence of TiB₂ particles, the machinability is still a problem which restricts the application of TiB₂/Al MMCs. In order to meet the industrial requirements, the influence of TiB₂ particles on the machinability of TiB₂/Al MMCs was investigated experimentally. Moreover, the optimal machining conditions for this kind of MMCs were investigated in this study. The major conclusions are: (1) the machining force of TiB₂/Al MMCs is bigger than that of non-reinforced alloy and mainly controlled by feed rate; (2) the residual stress of TiB₂/Al MMCs is compressive while that of non-reinforced alloy is nearly neutral; (3) the surface roughness of TiB₂/Al MMCs is smaller than that of non-reinforced alloy under the same cutting speed, but reverse result was observed when the feed rate increased; (4) a multi-objective optimization model for surface roughness and material removal rate (MRR) was established, and a set of optimal parameter combinations of the machining was obtained. The results show a great difference from SiC particle reinforced MMCs and provide a useful guide for a better control of machining process of this material.