Numerical investigation on flow nonuniformity-induced hysteresis in scramjet isolator

Numerical simulation and theoretical analysis were conducted to study the hysteresis inside scramjet isolator during the reciprocating process of back pressure variation. It is revealed that only a regular reflection is theoretically possible for two leading shocks when the inflow Mach number is greater than 2.0, and no hysteresis can occur in the transition between shock reflection types. Nevertheless, wall suction, gas injection, and background waves cause non-uniformity of the incoming flow and would make hysteresis possible. Besides the classical hysteresis in the transition between shock reflection, new kinds of hysteresis were found in both the deflection angle of separated boundary layer and the location of the shock train. Moreover, the occurrence of hysteresis in the deflection angle of the separated boundary layer is accompanied with the shock reflection hysteresis. In the case with background waves or gas injection, hysteresis in the starting position of leading shock was observed too. As back pressure decreases, the leading shock does not follow the same path as that as the back pressure increases, and it is anchored at the location where the background shock or the injection interacts with the leading shock. It is inferred that, if two strong adverse pressure gradient regions move towards and interact with each other, hysteresis will take place when they start to separate.     

硅谐振式压力微传感器闭环系统

硅谐振压力微传感器在自激振荡回路中采取电阻热激励、电阻拾振时得到的信号,由于有用信号本身的量级小,因而含有严重的同频干扰信号(耦合激励信号),信噪比SNR (Signal Noise Ratio)仅为10^-3数量级.为了提高信噪比,滤除同频干扰,多级放大之后的处理中将锁相环PLL(Phase-Locked Loop)工作原理和分频技术相结合,由锁相环输出作为传感器的激励和鉴相相关信号,搭建硅谐振压力微传感器闭环自激振荡回路.结果表明:采用锁相分频技术的微传感器闭环系统能可靠运行,信噪比低的问题得到了很好解决.     

飞行器伺服回路的变结构设计

本文根据变结构系统(VSS)理论对某飞行器伺服回路进行了变结构设计,给出了控制器设计的详尽步骤。设计方法几何意义直观,在IBM4341机上通过了数字仿真,给出了仿真框图,并与原伺服回路的控制性能进行了比较。仿真表明,VSS比传统普通控制系统具有以下几个突出的优点;(1)快速、无超调、无稳态误差:(2)对系统参数变化具有鲁棒性;(3)对外界干扰具有鲁棒性。     

Effects of yaw-roll coupling ratio on lateral-directional aerodynamic characteristics

Experimental investigation of large amplitude yaw-roll coupled oscillations was conducted in a low-speed wind tunnel using an aircraft configuration model. A special test rig was designed and constructed to provide different coupled motions from low to high angles of attack.A parameter ‘‘coupling ratio" was introduced to indicate the extent of yaw-roll coupling. At each pitch angle, seven coupling ratios were designed to study the yaw-roll coupling effects on the lateraldirectional aerodynamic characteristics systematically. At high angles of attack, the damping characteristics of yawing and rolling moments drastically varied with coupling ratios. In the coupled motions with the rotation taking place about the wind axis, the lateral-directional aerodynamic moments exhibited unsteady characteristics and were different from the ‘‘quasi-steady" results of the rotary balance tests. The calculated results of the traditional aerodynamic derivative method were also compared with the experimental data. At low and very high angles of attack, the aerodynamic derivative method was applicative. However, within a wide range of angles of attack, the calculated results of aerodynamic derivative method were inconsistent with the experimental data, due to the drastic changes of damping characteristics of lateral-directional aerodynamic moments with yaw-roll coupling ratios.     

CPL蒸发器多孔芯内传热传质的非稳态数值模拟

基于多孔芯内局部热力学平衡的假设，考虑了Brinkman和Forchheimer对Darcy定律的修正模型，针对简化的物理模型中所包含的气液相区域，建立了二维分层饱和多孔介质模型，以甲醇为工质对CPL，蒸发器毛细多孔芯内的传热传质过程进行非稳态数值模拟。在不同的热负荷条件下预测气液分层界面的形状和位置、系统由初态达到稳态过程的持续时间，讨论压力和温度的分布。由两层饱和模型所得到的计算结果可知．CPL系统在启动时，为避免高热流时液体脱离多孔区而发生干涸，宜采用小负荷启动；采用预热器，改善蒸气的出口条件；增加蒸发器入口处的工质的过冷度，有利于增加CPL系统启动过程和变工况时的稳定性。文中分析结论为CPL系统的优化设计提供参考。     

Stability analysis of an aeroelastic system with friction

In this paper, harmonic balance method, exact formulation and numerical simulation method are adopted to study the effects of different friction stiffness on the stability of 1.5 degrees of freedom aeroelastic system. On this basis, the expressions of input energy and dissipated energy are deduced, and the energy method is used to reveal the mechanisms of the stable boundary and unstable boundary existing in the system and the effects of different friction stiffness on the stability of the system. Studies have shown that the stability region and the critical aerodynamic damping ratio of the system rise with the increase of the friction stiffness, while the friction stiffness has little effect on the stability boundary. In the analysis of the stability of system, the results of harmonic balance method, exact formulation and Newmark of numerical simulation method are in good agreement. Compared with exact formulation and numerical simulation method, the concept and conclusion of harmonic balance method are simple in the system stability analysis.     

基于开路电压法的电池荷电状态估计误差校正

本文提出分别研究电池开路电压在充电结束后停置过程和放电结束后停置过程的不同变化规律,并考虑了不同停置时间在两个过程中的作用和影响,从而达到提高开路电压法估算荷电状态精度的效果。实验验证表明,此方法的精度比传统开路电压法更加准确。     

Mechanism analysis of hysteretic aerodynamic characteristics on variable-sweep wings

Variable-sweep wings have large shape-changing capabilities and wide flight envelops, which are considered as one of the most promising directions for intelligent morphing UAVs. Aerodynamic investigations always focus on several static states in the varying sweep process, which ignore the unsteady aerodynamic characteristics. However, deviations to static aerodynamic forces are inevitably caused by dynamic sweep motion. In this work, first, unsteady aerodynamic characteristics on a typical variable-sweep UAV with large aspect ratio were analyzed. Then, deep mechanism of unsteady aerodynamic characteristics in the varying sweep process was studied. Finally, numerical simulation method integrated with structured moving overset grids was applied to solve the unsteady fluid of varying sweep process. The simulation results of a sweep forward-backward circle show a distinct dynamic hysteresis loop surrounding the static data for the aerodynamic forces. Compared with the static lift coefficients , at the same sweep angles, dynamic  lift coefficient in sweep forward process are all smaller, while dynamic sweep backward  lift coefficient are all larger. In addition, dynamic deviations to static  lift coefficient are positively related with the varying sweep speeds. Mechanism study on the unsteady aerodynamic characteristics indicates that three key factors lead to the dynamic hysteresis loop in varying sweep process. They are the effects of additional velocity caused by varying sweep motion, the effects of flow hysteresis and viscosity. The additional velocity induced by sweep motion affects the transversal flow direction along the wing and the effective angle of attack at the airfoil profile. The physical properties of flow, the hysteresis and viscosity affect the unsteady aerodynamic characteristics by flow separation and induced vortexes.     

一种数字化DS/BPSK扩频接收机

介绍一种新型数字化DS/BPSK(Direct Spread/Binary Phase Shife Keying)扩频接收机的设计.该接收机采用专用数字相关器为核心的硬件设计,并结合数字处理算法完成扩频信号的解调.技术上采用串并组合的伪码捕获、科斯特环载波跟踪、延迟锁定环伪码跟踪等方式,可通过软件算法灵活实现.该接收机具有综合性能强,及软件接口灵活的特点,可有效地应用于基于码分多址的多目标测控系统中.     

Digital fixed-frequency hysteresis current control of a BLDC motor applied for aerospace electrically powered actuators

In the conventional cascade control structure of aerospace electrically powered actuators, the current (or electromagnetic torque) loop plays a critical role in realizing a rapid response for a digitally controlled BrushLess Direct Current (BLDC) motor. Hysteresis Current Control (HCC) is an effective method in improving the performance of current control for a BLDC motor. Nevertheless, the varying modulating frequency in the traditional HCC causes severe problems on the safety of power devices and the electromagnetic compatibility design. A triangular carrier-based fixed-frequency HCC strategy is expanded by relaxing the constraints on the rising and descending rates of the winding current to advance the capability of HCC to realize fixed-frequency modulation in the steady state. Based on that, a new flexible-bound-size quasi-fixed-frequency HCC is proposed, and the range feasible to realize fixed-frequency modulation control can cover the entire running process in the steady state. Meanwhile, a corresponding digital control strategy is designed, and four digitalization rules are proposed to extend the capacity to achieve fixed-frequency modulation control to the unsteady working state, that is, a novel fixed-frequency modulation is realized. Simulation and experimental results prove the effectiveness of this improved fixed-frequency HCC strategy.