排序方式: 共有67条查询结果,搜索用时 78 毫秒
1.
《中国航空学报》2020,33(3):1074-1084
Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition. 相似文献
2.
3.
《中国航空学报》2020,33(6):1799-1811
The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected. 相似文献
4.
采用激光多普勒测速技术对光滑和粗糙槽道湍流特性进行了实验研究。粗糙元为二维横向V型沟槽,沟槽深度为0.8mm,沟槽间距为6.4mm,对应的槽道半高度与沟槽深度比为12.5。基于中线时均速度和槽道半高度的流动雷诺数范围为2740~17400。实验测量了包括时均速度、湍流强度、雷诺切应力和速度脉动偏斜因子和平坦因子在内的湍流统计量,结果表明沟槽型粗糙度对湍流的影响不仅局限于边界层内区,而是延伸到整个边界层范围。粗糙壁面上的粗糙度函数随雷诺数的增大而增大,时均亏损速度也较光滑壁面高。沟槽抑制了内区的流向湍流强度,同时增大了外区的湍流强度。粗糙壁面上的雷诺切应力高于光滑壁面,且与湍流强度一样表现出对雷诺数的依赖性。尽管沟槽型粗糙度对流向平坦因子影响不大,但对流向偏斜因子有显著影响。 相似文献
5.
6.
7.
The effectiveness of grinding fluid supply has a crucial impact on grinding quality and efficiency in high speed grinding. In order to improve the cooling and lubrication, through in-depth research of self-inhaling internal cooling method and intermittent grinding mechanism, a new spray cooling method used in high speed grinding is proposed. By referring to the structure of bowl- shaped dispersion disk, the grinding wheel matrix with atomization ability is designed; through studying heat transfer of droplet collision and the influence of micro-groove on the boiling heat transfer, grinding segment with micro-groove is designed to enhance the heat flux of coolant and achieve maximum heat transfer between droplets and grinding contact zone. High-speed grinding experiments on GH4169 with the developed grinding wheel are carried out. The results show that with the micro-groove grinding wheel just 5.4% of pump outlet flow rate and 0.5% of spindle energy is needed to reduce the grinding temperature to 200℃, which means the developed grinding wheel makes cooling high efficient and low energy consuming. 相似文献
8.
侧载及加热方位对槽道内临界热流密度影响 总被引:1,自引:0,他引:1
为了研究侧载以及加热方位对矩形窄缝槽道内临界热流密度特性的影响,在旋转平台上进行了两相流的超重力实验.以蒸馏水为工质,通过改变质量流速、入口温度、侧载大小以及加热方位,获得了发生临界换热现象时的质量流速、实验段压降和壁温的变化趋势,考察了侧载和加热方位对临界热流密度的影响规律,并对侧载下两相流不稳定性进行了简析.实验表明:发生临界换热时,壁温迅速上升,有效加热热流开始减少,关闭加热电源后,实验段压降下降、质量流速回升较明显;侧载以及不同的加热方位对临界热流密度有明显影响;临界热流密度发生前后,蒸汽回流导致进口温度上升,增加了流动的不稳定性. 相似文献
9.
为了研究螺旋槽端面气膜密封结构在高温下的密封性能,建立了高温密封分析数学模型,研究了螺旋槽气膜密封的气膜温度、压力以及端面变形分布规律,在此基础上探讨了螺旋槽气膜密封的热变形机理,并进一步分析了不同密封压力、转速、环境温度下热效应对开启力和泄漏率的影响。结果表明:在高压、高速条件下,热效应使端面形成发散间隙,导致开启力减小,泄漏率增加;在低压、高速条件下,热效应使端面形成收敛间隙,导致开启力及泄漏率增大。对于螺旋槽端面气膜密封结构,环境温度的升高对端面变形的影响不明显,且环境温度从300 K升至550 K时,考虑端面热效应的开启力减小4%,泄漏率减少36%。 相似文献
10.
郝芳 《运载火箭与返回技术》2006,27(1):67-70,66
文章介绍了钢球连接方式火工装置中,钢球连接处的结构强度校核。通过经典的接触应力计算公式,结合钢球在火工装置上的具体使用情况,利用微变形理论,归纳出了火工装置上起连接承载作用的钢球连接方式新的强度校核判断法则。试验结果表明,该判据能够较为真实地反映火工装置上钢球连接方式的结构承载能力。 相似文献