排序方式: 共有33条查询结果,搜索用时 31 毫秒
1.
本文讨论了舰载飞机以小于有利速度着舰时的航迹稳定性问题。在分析飞机航迹稳定性的同时,还对油门杆控制、机动襟翼控制对改善航迹稳定性的作用进行了初步探讨;在此基础上还讨论了舰载飞机加装波束导引系统对着舰过程的影响原理。结果表明:采用油门杆控制、机动襟翼控制来改善着舰阶段的航迹稳定性是可行的:而且用以上两控制系统作为内环的自动驾驶仪在波束导引系统自动导引飞机着舰过程中,能控制飞机的飞行速度、高度,帮助驾驶员操纵。 相似文献
2.
导弹姿态控制伺服系统的变结构控制 总被引:2,自引:0,他引:2
为消除导弹姿态控制伺服系统变结构控制中的抖振,在状态轨迹与滑动平面夹角变结构控制律的基础上,将原来的二阶系统扩展为n阶。所设计的控制律兼具连续控制律与非连续控制律的优点,动态品质优良。仿真结果验证了理论分析的有效性。 相似文献
3.
4.
以三颗非共轨的Walker星座卫星为研究对象, 对航天器无需变轨与其接近的可能性进行研究. 将Lambert方法得到的航天器轨道作为初始轨道, 利用遗传算法对初始轨道进行优化. 对初始轨道在参考时刻位置和速度的改变量进行编码,形成对应的种群. 以航天器与星座卫星之间的最近距离为适应度函数, 通过种群的繁殖得到优化结果. 结合仿真算例, 分析了最小二乘算法和遗传算法在轨道优化中的优劣以及接近过程中轨道摄动的影响. 结果表明, 遗传算法适用于所提出的轨道改进问题. 研究结果可为单航天器无需变轨对星座多星接近问题提供理论依据. 相似文献
5.
New Cutting Force Modeling Approach for Flat End Mill 总被引:1,自引:1,他引:0
WAN Min ZHANG Wei-hong TAN Gang QIN Guo-hua 《中国航空学报》2007,20(3):282-288
A new mechanistic cutting force model for flat end milling using the instantaneous cutting force coefficients is proposed. An in-depth analysis shows that the total cutting forces can be separated into two terms: a nominal component independent of the runout and a perturbation component induced by the runout. The instantaneous value of the nominal component is used to calibrate the cutting force coefficients. With the help of the perturbation component and the cutting force coefficients obtained above, the cutter runout is identified. Based on simulation and experimental results, the validity of the identification approach is demonstrated. The advantage of the proposed method lies in that the calibration performed with data of one cutting test under a specific regime can be applied for a great range of cutting conditions. 相似文献
6.
张惠玲 《西安航空技术高等专科学校学报》2007,25(1):61-63
通过用一组非线性方程组来逼近线性规划的Kuhn-mcker条件方程,从而将求解线性规划问题转化为一个用Newton迭代法来求解非线性方程组的问题。经数值计算表明,该算法在一般情况下能实现快速收敛。 相似文献
7.
建构主义教学模式对大学生学习方式有重要影响,通过实证研究方法,研究了课堂环境下建构主义教学模式与大学生学习方式之间的内在关系。研究结果表明:以互动性、自主性为特征的建构主义教学模式与深层学习方式显著正相关,教学模式中的自主性对深层动机和策略的影响均显著高于互动性,且自主性可以更为有效地促使学生采用深层学习方式。 相似文献
8.
针对电传控制增稳飞机进行了进场着陆的飞行品质地面模拟试验研究,验证了适合于进场着陆的控制律,并得出一些重要的有关进场着陆的驾驶员评定意见。此外,还计算了轨迹角超调值,验证了该参数数可以作为一个重要的飞行品质准则。 相似文献
9.
杨俊 《中国民航飞行学院学报》2013,(1):12-15
大气紊流和风切变对飞行活动影响较大,尤以低空风切变危害最大,严重威胁着民航飞行的安全。鉴于飞行器对抗大气扰动的实际能力有限,正确的飞行对策是回避或改出危险的大气扰动区。本文对某训练飞机着陆进近遭遇风切变时飞机轨迹的变化进行了模拟仿真计算。结果表明,采用恒定迎角策略,即采用最大允许迎角(抖动迎角)和最大油门时,改出效果最佳。同时计算出了某训练飞机在水平风为0时,所能抵抗的最大垂直阵风强度;以及在垂直阵风为0时,所能抵抗的最大水平风强度。 相似文献
10.
Chan-oh Min Dae-woo Lee Kyeum-rae Cho Sung-jin Jo Jang-sik Yang Won-boo Lee 《Aerospace Science and Technology》2011,15(4):269-282
The reentry vehicle is affected by various disturbances such as a wind gust, atmospheric condition or aerodynamic problems in the approach and landing phase. Therefore it is necessary to design a robust control scheme. This paper presents a control scheme using Mamdani fuzzy PD controller. In this paper, the reference trajectories are generated using geometric parameters for disturbed circumstances with 4 cases: nominal, headwind and tailwind, drag increased case. Then, a Mamdani fuzzy PD controller was designed in this study. Twenty-five rules were applied in the knowledge-based system. The max–min method for a fuzzy inference system and the center-of-mass method in defuzzification were used. Finally, guidance and control simulations are performed for verification of proposed controller using generated reference trajectories. In addition, the Monte Carlo simulation is performed considering various disturbances. The results show that proposed Mamdani fuzzy PD controller has reliability and robustness for control of reentry vehicle with wind disturbance in the approach and landing phases. 相似文献