Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

Turbulence modelling of the aerodynamic interaction of OGV wakes and diffuser flow

Different turbulence closures were used to predict the flow interaction between the wakes created by compressor outlet guide vanes（OGVs） and a downstream annular pre-diffuser.Two statistical turbulence...     

Thermal Fatigue Behavior of Ni_3Al Based Superalloy IC6E

The thermal fatigue behavior of Ni3Al based superalloy IC6E during the cycles between 900 ℃/1 000 ℃ and the room tempera-ture was investigated. The experimental results indicate that the primary and secondary thermal fatigue cracks initiate inside or round the borides and then spread away along grain boundaries and/or in interdendritic areas. The fracture of borides and their separation from the matrix at interfaces are mainly responsible for the crack initiation and its spreading. At temperatures higher than 1 000 ℃, the grain boundary oxidation combined with cyclic stresses accelerates the crack growth.     

Combustion Synthesis of h-BN-SiC Ceramic Composites

The feasibility was demonstrated to fabricate h-BN-SiC ceramics through combustion synthesis of the mixture of boron carbide and silicon powders under 100 MPa nitrogen pressure. The mass fraction of BN and SiC in the combustion products were found to be 72 % and 28 % respectively. The thermodynamics of the synthesis reaction and the adiabatic combustion temperature were calculated on the theoretical ground. The bending strengths of the ceramics were measured to be 65.2 MPa at room temperature and 55 MPa at 1350 ℃. The phase composition and microstructure of the combustion products were identified by X-ray diffraction (XRD) and scanning electron microscopy (SEM).     

Preparation,Growth Mechanisms and Characterizations of ZnSe Films via the Solvothermal Method

With diethylamine as a solvent, ZnSe films were formed on the Si substrate directly from zinc and selenium through the modified solvothermal method. The effects of holding temperature, deposition time and substrate surface treatment on the quality and morpholo-gies of the ZnSe films were investigated. The growth mechanism of ZnSe films was proved to be a layer-nucleation growth process, which was tied in with the Stranski-Krastanov (SK) model. ZnSe films were identified by the X-ray diffraction pattern (XRD), the scan-ning electron microscope (SEM), the X-ray photoelectron spectroscope (XPS) and the photoluminescence (PL) techniques. The results indicate that the modified solvothermal method with diethylamine as a solvent is suitable to prepare high quality ZnSe films.     

Effect of interface debonding on matrix multicracking evolution of fiber-reinfroced ceramic-matrix composites

An analytical methodology was developed to investigate the effect of fiber/matrix interface debonding on matrix multicracking evolution of fiber-reinforced CMCs(ceramic-matrix composites). The Budiansky-Hutchinson-Evans shear-lag model was adopted to analyse the micro-stress field of the damaged composites. The critical matrix strain energy criterion, which presupposes the existence of an ultimate or critical matrix strain energy with matrix, was obtained to simulate the matrix multicracking evolution of CMCs. With the increase of the applied stress, the matrix multicracking and fiber/matrix interface debonding occurred to dissipate the additional energy entered into the composites. The fiber/matrix interface debonded length under matrix multicracking evolution was obtained by treating the interface debonding as a particular crack propagation problem. The conditions for no-debonding and debonding during the evolution of matrix multicracking were discussed in terms of two interfacial properties, i.e., the interface shear stress and interface debonded toughness. When the fiber/matrix interface was bonded, the matrix multicracking evolution was much more intense compared with the interface debonding; when the fiber/matrix interface was debonded, the matrix crack density increased with the increasing of interface shear stress and interface debonded energy. The theoretical results were compared with experimental data of unidirectional SiC/CAS(calcium alumina silicate), SiC/CAS-Ⅱ and SiC/borosilicate composites.      

GNSS驯服芯片级原子钟方法研究CSCD

芯片级原子钟是一种体积小且功耗低的高精度时钟源,具有广泛的用途。针对这一特点,设计了基于GNSS的芯片级原子钟驾驭算法。以GNSS系统时作为参考,测量芯片级原子钟与GNSS系统时间的钟差,并对芯片级原子钟进行钟差建模,获取其特征参数。通过乒乓法计算出钟驾驭调整量,对芯片级原子钟进行控制,最终将芯片级原子钟驾驭到GNSS系统时间上。经过实验验证,在驾驭时间常数为100s的情况下,芯片级原子钟与GNSS系统时间的时钟同步误差在-7.5~7.5ns之间;1h频率准确度为5.8×10-13;平均时间为10000s时的频率稳定度为3×10-13。     

飞机外形参数的气动与隐身综合优化设计

以气动力及雷达散射截面参数为目标函数,主要优化对总体外形和飞机性能影响较大的机翼、尾翼的平面形状几何参数以及少数几个机身几何参数;根据第4代战斗机的设计要求,确定各个目标的理想值、最低可接受值,以及各个约束的满足区间,应用模糊优化理论,建立各个目标的满意度函数及各个约束条件的满足度函数,并使用多目标总满意度函数和常权、变权的不同组合,建立了5种外形参数模糊优化模型,使设计人员可以根据不同的设计思想和设计目的选择优化模型与翼面形状的组合.     

A novel strategy for fine-grained semantic verification of civil aviation radiotelephony read-backs

During the flight of the aircraft, the pilot must repeat the instruction sent by the controller, and the controller must further confirm these read-backs, in this way to further ensure the safety of air transportation. However, fatigue, tension, negligence and other human factors may prevent the controller from realizing read-back errors in time, which is a huge hidden danger for the safety of civil aviation transportation. This paper proposes a novel strategy to implement fine-grained semantic ...     

Numerical analysis of deflection control of a gas plasma jet based on magnetohydrodynamic staggered electrode configuration

To control the deflection of the gas plasma jet, a new analytical method is proposed based on the Magnetohydrodynamic(MHD) technique. Based on the typical MHD power generation model, the applied voltage is applied to the staggered electrodes, that is, a pair of electrodes on the same side wall are connected to generate an axial current in the channel. Under the action of the magnetic field perpendicular to the direction of the flow, the plasma is subjected to electromagnetic forces perpendicular...