Impact of rain on wave retrieval from Sentinel-1 synthetic aperture radar images in tropical cyclones

The main objective of our work was to investigate the impact of rain on wave observations from C-band (~5.3 GHz) synthetic aperture radar (SAR) in tropical cyclones. In this study, 10 Sentinel-1 SAR images were available from the Satellite Hurricane Observation Campaign, which were taken under cyclonic conditions during the 2016 hurricane season. The third-generation wave model, known as Simulating WAves Nearshore (SWAN) (version 41.31), was used to simulate the wave fields corresponding to these Sentinel-1 SAR images. In addition, rainfall data from the Tropical Rainfall Measuring Mission satellite passing over the spatial coverage of the Sentinel-1 SAR images were collected. The simulated results were validated against significant wave heights (SWHs) from the Jason-2 altimeter and European Centre for Medium-Range Weather Forecasts data, revealing a root mean square error (RMSE) of ~0.5 m with a 0.25 scatter index. Winds retrieved from the VH-polarized Sentinel-1 SAR images using the Sentinel-1 Extra Wide-swath Mode Wind Speed Retrieval Model after Noise Removal were taken as prior information for wave retrieval. It was discovered that rain did indeed affect the SAR wave retrieval, as evidenced by the 3.21-m RMSE of SWHs between the SAR images and the SWAN model, which was obtained for the ~1000 match-ups with raindrops. The raindrops dampened the wave retrieval when the rain rate was < ~5 mm/hr; however, they enhanced wave retrieval for higher rain rates. It was also found that the portion of the rain-induced ring wave with a wave number > 0.05 rad/m (~125 m wavelength) was clearly observed in the SAR-derived wave spectra.     

Sustained data recording system based on disk array

Most sustained data recording systems in many real-time fields are based on tape equipments. We have developed an innovative sustained data recording system based on disk array which consists of Array Controller Module (ACM), String Controller Module (SCM) and Main Controller Module (MCM). This system has a better performance and higher reliability than the traditional tape recorder and can be used conveniently in many areas of data recording, storing, playback, and remote backup. This novel recording system has been used in radar data recorder for spacecraft orbit tracking and satellite remote sensing data recording successfully.     

关于Salomon假设的研究综述

高速切削技术在航空航天工业中应用广泛,取得了巨大的经济效益.Salomon假设作为金属切削领域一个著名的科学猜想,被认为是高速切削技术的发端.本文讨论了Salomon假设的起源,从理论研究、仿真分析和实验验证等方面总结了历史上学者对Salomon假设的研究成果,论述了Salomon假设的工程实践意义.结论认为Salomon假设实际上并未证实,其关于温度变化的假设成立与否应该取决于对切削温度的确切定义,而关于刀具磨损的假设已基本可以否定.最后展望了Salomon假设的未来研究趋势.     

无铅焊接在电路板接线柱的应用

利用无铅焊料具有较高熔点的温度特性,选用无铅焊料对电路板接线柱焊接,避免在接线柱上焊接导线时电路板焊点易受热熔化,接线柱产生下陷、歪斜等问题。通过可焊性、绝缘电阻测试、氯离子浓度检测、高低温实验、焊点拉脱力测试、振动试验等,介绍了无铅焊接在这种电路板接线柱应用中的各项工艺参数、手工焊接工具及无铅焊料的选择。     

疲劳裂纹扩展速率试验数据的可靠性分析模型

以指定ΔＫ下的ｄａ／ｄＮ服从对数正态分布为基础，提出３种ｄａ／ｄＮ试验数据统计处理方法；依据一组４０ＣｒＮｉＭｏ材料的ＣＴ试样的试验数据处理结果，对３方法进行了分析对比。     

1553B与CAN总线的互连

介绍了 1553 B与 CAN总线的互连方法 ,并分析了互连的实时性与可靠性 ,指出 CAN总线相对于 1553 B的优缺点。     

Phugoid oscillations in optimal reentry trajectories

A major problem with operations of lifting reentry vehicle having an aft center-of-gravity location due to large engine mass at the rear is the required hypersonic trim to fight the desired trajectory. This condition is most severe for lifting maneuvers. As a first step toward analyzing this problem, this paper considers the lift requirement for some basic maneuvers in the plane of a great circle. Considerations are given to optimal lift control for achieving the maximization of either the final altitude, speed or range. For the maximum-range problem, phugoid oscillation along an optimal trajectory is less severe as compared to a glide with maximum lift-to-drag ratio. An explicit formula for the number of oscillations for an entry from orbital speed is proposed.     

风挡防冰表面温度场计算

在研究国内外有关资料的基础上，采用了量纲分析的方法，建立了风挡外表面温度场的计算模型。回避了对自由流与射流相互干扰这一复杂问题的研究，同时对该计算模型进行了验证，并开发了相应的计算程序。该问题的解决，填补了国内在该领域中的空白。     

板料成形的数值分析及程序系统

本文讨论了板料成形的数值分析方法,并介绍一个能在微机上运行的程序系统——CASF(Computer Aided Sheetmetal Forming)01系统。 CASF01系统采用参数三次样条描述板金零件的几何外形,按弹-塑性流动理论用完全拉格朗日有限元法计算成形过程中的应力应变分布。由于参数样条的插值性和分段描述特点与有限元法的结构离散在基本思想和处理方法上的相似性,系统内曲面描述和力学分析程序间数据传递迅速方便。圆板胀形及其汽车零件的计算实例表明了CASF01系统的可靠性和实用性。     

基于CORBA实现专业领域软件在网络环境下的集成

如何有效地将已有系统集成或移植到新系统中 ,是集成系统开发中提出的一个重要问题。本文基于CORBA技术探讨如何实现遗留系统集成的方法 ,并通过实例重点阐述如何将已有的系统封装成CORBA对象的步骤。