基于DLatLRR与VGG Net的红外与可见光图像融合

针对红外与可见光图像融合中特征损失严重、显著目标不突出的问题，提出了一种低秩表示分解与深度神经网络相结合的图像融合算法。首先，对源图像进行潜在低秩表示分解（DLatLRR），得到相应的低秩部分、显著部分及稀疏噪声。然后，分别采用16层的VGG Net模型和联合特征加权算法对低秩部分与显著部分进行融合，舍弃二者的稀疏噪声。最后，对融合得到的低秩部分和显著部分进行图像重建，得到最终的融合图像。实验结果表明:与其他算法进行比较，所提算法能够对图像的深层次细节特征进行融合，突出场景中的感兴趣区域，且融合图像的相关差异和、结构相似性、线性相关度等多种客观指标均有所提升，提升最大值分别为0.73、0.15、0.11，噪声产生率的最大缩减值为0.041 2。      

Effect of matching between the magnetic field and channel length on the performance of low sputtering Hall thrusters

Discharge characteristics of a non-wall-loss Hall thruster were studied under different channel lengths using a design based on pushing a magnetic field through a double permanent magnet ring. The effect of different magnetic field intensities and channel lengths on ionization, efficiency, and plume divergence angle were studied. The experimental results show that propellant utilization is improved for optimal matching between the magnetic field and channel length. While matching the magnetic field and channel length, the ionization position of the neutral gas changes. The ion flow is effectively controlled, allowing the thrust force, specific impulse, and efficiency to be improved. Our study shows that the channel length is an important design parameter to consider for improving the performance of non-wall-loss Hall thrusters.     

Facile Fabrication of Hierarchical Porous N/O Functionalized Carbon Derived from Blighted Grains Towards Electrochemical Capacitors

The hierarchical porous N/O co-functionalized carbon(HPNOC)was scalably prepared by using the lowcost and renewable blighted grains as the raw material coupled with mild KHCO_3 activation for electrochemical capacitors(ECs).The elemental N was in situ doped in the obtained HPNOC without any N-containing additives.Remarkably,the obtained HPNOC was endowed with a large specific surface area(about 2 624m~2·g~(-1)),high pore volume(about 1.35cm~3·g~(-1)),as well as high-content N/O functionalization(about 1.9%(in atom)N and about 10.2%(in atom)O.Furthermore,the as-resulted HPNOC electrode with a high mass loading of 5mg·cm~(-2 )exhibited competitive gravimetric capacitances of about 373.6F·g~(-1 )at 0.5A·g~(-1),and even about 260.4F·g~(-1 )at a high rate of 10A·g~(-1);superior capacitance retention of about 98.8%at 1A·g~(-1 )over 10 000consecutive cycles;and high specific energy of about 9.6W·h·kg~(-1 )at a power of 500W·kg~(-1),when evaluated as a promising electrode in 6mol KOH for advanced electrochemical supercapacitors.More encouragingly,the green synthetic strategy we developed holds a huge promise in generalizing for other biomass-derived carbon materials for versatile energy-related applications.     

Impact of rain on wave retrieval from Sentinel-1 synthetic aperture radar images in tropical cyclones

The main objective of our work was to investigate the impact of rain on wave observations from C-band (~5.3 GHz) synthetic aperture radar (SAR) in tropical cyclones. In this study, 10 Sentinel-1 SAR images were available from the Satellite Hurricane Observation Campaign, which were taken under cyclonic conditions during the 2016 hurricane season. The third-generation wave model, known as Simulating WAves Nearshore (SWAN) (version 41.31), was used to simulate the wave fields corresponding to these Sentinel-1 SAR images. In addition, rainfall data from the Tropical Rainfall Measuring Mission satellite passing over the spatial coverage of the Sentinel-1 SAR images were collected. The simulated results were validated against significant wave heights (SWHs) from the Jason-2 altimeter and European Centre for Medium-Range Weather Forecasts data, revealing a root mean square error (RMSE) of ~0.5 m with a 0.25 scatter index. Winds retrieved from the VH-polarized Sentinel-1 SAR images using the Sentinel-1 Extra Wide-swath Mode Wind Speed Retrieval Model after Noise Removal were taken as prior information for wave retrieval. It was discovered that rain did indeed affect the SAR wave retrieval, as evidenced by the 3.21-m RMSE of SWHs between the SAR images and the SWAN model, which was obtained for the ~1000 match-ups with raindrops. The raindrops dampened the wave retrieval when the rain rate was < ~5 mm/hr; however, they enhanced wave retrieval for higher rain rates. It was also found that the portion of the rain-induced ring wave with a wave number > 0.05 rad/m (~125 m wavelength) was clearly observed in the SAR-derived wave spectra.     

Orbital stability close to asteroid 624 Hektor using the polyhedral model

We investigate the orbital stability close to the unique L4-point Jupiter binary Trojan asteroid 624 Hektor. The gravitational potential of 624 Hektor is calculated using the polyhedron model with observational data of 2038 faces and 1021 vertexes. Previous studies have presented three different density values for 624 Hektor. The equilibrium points in the gravitational potential of 624 Hektor with different density values have been studied in detail. There are five equilibrium points in the gravitational potential of 624 Hektor no matter the density value. The positions, Jacobian, eigenvalues, topological cases, stability, as well as the Hessian matrix of the equilibrium points are investigated. For the three different density values the number, topological cases, and the stability of the equilibrium points with different density values are the same. However, the positions of the equilibrium points vary with the density value of the asteroid 624 Hektor. The outer equilibrium points move away from the asteroid’s mass center when the density increases, and the inner equilibrium point moves close to the asteroid’s mass center when the density increases. There exist unstable periodic orbits near the surface of 624 Hektor. We calculated an orbit near the primary’s equatorial plane of this binary Trojan asteroid; the results indicate that the orbit remains stable after 28.8375?d.     

Evaluation of a regional real-time precise positioning system based on GPS/BeiDou observations in Australia

The performance of real-time (RT) precise positioning can be improved by utilizing observations from multiple Global Navigation Satellite Systems (GNSS) instead of one particular system. Since the end of 2012, BeiDou, independently established by China, began to provide operational services for users in the Asia-Pacific regions. In this study, a regional RT precise positioning system is developed to evaluate the performance of GPS/BeiDou observations in Australia in providing high precision positioning services for users. Fixing three hourly updated satellite orbits, RT correction messages are generated and broadcasted by processing RT observation/navigation data streams from the national network of GNSS Continuously Operating Reference Stations in Australia (AUSCORS) at the server side. At the user side, RT PPP is realized by processing RT data streams and the RT correction messages received. RT clock offsets, for which the accuracy reached 0.07 and 0.28?ns for GPS and BeiDou, respectively, can be determined. Based on these corrections, an accuracy of 12.2, 30.0 and 45.6?cm in the North, East and Up directions was achieved for the BeiDou-only solution after 30 min while the GPS-only solution reached 5.1, 15.3 and 15.5?cm for the same components at the same time. A further improvement of 43.7, 36.9 and 45.0 percent in the three directions, respectively, was achieved for the combined GPS/BeiDou solution. After the initialization process, the North, East and Up positioning accuracies were 5.2, 8.1 and 17.8?cm, respectively, for the BeiDou-only solution, while 1.5, 3.0, and 4.7?cm for the GPS-only solution. However, we only noticed a 20.9% improvement in the East direction was obtained for the GPS/BeiDou solution, while no improvements in the other directions were detected. It is expected that such improvements may become bigger with the increasing accuracy of the BeiDou-only solution.     

液体火箭发动机协同设计平台关键技术

针对液体火箭发动机协同设计工程实际需求,围绕研制数据高效流转与协同,面向产品全生命周期跨地域、跨专业特点,提出了协同设计平台框架。针对协同平台中的5项关键技术,给出了相应解决途径。基于PLM系统构建协同环境,建立统一编码,整合研制过程中的标准件、原材料等共性基础数据;通过基于MBD的三维结构设计,采用MBSE理念,以模型为载体升级发动机设计流程;采用线上IPT模式提升产品设计效率,同时实现全过程数据记录知识累积。采用BOM结构组织和展示不同设计阶段形成的数据;基于Hadoop平台分布式数据存储模式,实现结构化和非结构化数据综合管理。通过工程实践验证表明,构建的协同平台实现了基于数字化模型的设计工艺定制化协同,科研生产全过程的信息整合和多维度监控,促进了业务流程持续优化和研制效率不断提升,支撑发动机研制模式的转型升级。