Control of an aircraft electric fuel pump drive

The concept of designing a high-speed, permanent magnet, brushless DC motor aircraft fuel pump drive using a cycloconverter link is examined. A combination of sinusoidal and DC steady-state analysis is used to produce a simple model of the system. A closed-loop control system with an outer loop based on speed and an inner loop based on current is postulated wherein a proportional-plus-integral controller is placed in the forward path to assure minimum speed error. Gains are then set to assure that the eigenvalues of the linearized control system lie within the left half s-plane over the entire full range     

Optimal and Suboptimal Guidance for a Short-Range Homing Missile

Optimal and suboptimal guidance laws for short-range homing missiles are developed and compared to the commonly mechanized quidance law of proportional navigation. The optimal controller is derived as an optimal feedback regulator; the suboptimal controller is an approximation of the optimal regulator and consists of timevarying proportional navigation plus a time-varying gain term times a calculated target acceleration. Monte Carlo studies of the three controllers show that the optimal and suboptimal controllers are much superior to proportional navigation for the case of combined constant target acceleration, line-of-sight rate noise, and missile acceleration saturation.     

高温胁迫对岷江百合幼苗耐热指数和理化特性的影响

为了探明岷江百合幼苗在高温胁迫下的生理反应,以离体扩繁的岷江百合幼苗为研究材料,对其进行了不同高温(37 ℃/30 ℃、42 ℃/37 ℃)和不同时间(0、4、8、16、32、48 h)处理,研究了高温胁迫对其耐热指数和有关生理生化指标(叶绿素、丙二醛、游离脯氨酸、可溶性蛋白含量和SOD活性)的影响.结果表明:随着温度的升高和处理时间的延长,植株的耐热指数不断下降,叶绿素含量减少,丙二醛(MDA)含量增加;42 ℃胁迫32 h后,游离脯氨酸、可溶性蛋白含量、SOD活性均达到最大值,分别比对照增加了0.66倍、1.77倍和9.78倍.但胁迫48 h后,指标显著下降,这说明,42 ℃间断胁迫48 h对植株产生了不可逆的的热伤害作用.     

星载缝隙波导微波天线热控方案研究与验证

微波天线阵面的热变形是影响在轨指向精度的关键因素,如何解决大功率器件的散热问题至关重要。某微波天线热耗峰值近万瓦,在近20 m²的全阵面内,需要保证收发(TR)组件的温升和补偿加热器的功耗不能过高。针对某微波天线特有的工作模式和外热流情况,提出了机械泵驱动流体回路(MPFL)、双面散热和相变热管 3种热控方案,并分析了各自的特点和适用性。为解决天线内部狭小空间的辐射传导耦合问题,开展了单模块热阻实验分析与优化,并得到了在轨测试的验证。     

Cu对铝热法制备的Fe3Al-10％Ni块体纳米晶材料组织和性能影响

通过铝热法制备了Cu含量为2％,4％,6％(质量分数,下同)的Fe3Al-10％ Ni块体纳米晶材料,用光学显微镜(OM),电子探针(EPMA),X-射线衍射仪(XRD)和透射电镜(TEM)表征了材料的微观结构,并测定了材料的维氏硬度和室温压缩性能.结果表明:Cu含量低(2％)时,合金保持无序bcc结构,晶粒尺寸显著下...     

Implementation of CDFM Generator Control

The control of a cascaded doubly fed machine (CDFM) to be used for aircraft power generation is investigated. The controller employs a resistance simulator in the generator exciter to provide machine damping. Excitation is provided by a six step inverter fed from a controlled rectifier. Delays due to the dc link time constant cause the resistance simulation to be nonideal. An investigation into the ability of resistance simulation to provide damping under these conditions is described. The study includes linearized analysis, simulation, and laboratory tests. Good correlation between these methods was obtained throughout the study. Three control strategies for providing machine damping were investigated, and it is concluded that resistance simulation can be used to provide machine damping under these conditions.