全文获取类型
收费全文 | 187篇 |
免费 | 42篇 |
国内免费 | 42篇 |
专业分类
航空 | 119篇 |
航天技术 | 36篇 |
综合类 | 51篇 |
航天 | 65篇 |
出版年
2024年 | 1篇 |
2023年 | 3篇 |
2022年 | 10篇 |
2021年 | 9篇 |
2020年 | 5篇 |
2019年 | 9篇 |
2018年 | 14篇 |
2017年 | 14篇 |
2016年 | 7篇 |
2015年 | 11篇 |
2014年 | 3篇 |
2013年 | 5篇 |
2012年 | 15篇 |
2011年 | 15篇 |
2010年 | 14篇 |
2009年 | 5篇 |
2008年 | 8篇 |
2007年 | 8篇 |
2006年 | 10篇 |
2005年 | 11篇 |
2004年 | 3篇 |
2003年 | 3篇 |
2002年 | 2篇 |
2001年 | 5篇 |
2000年 | 8篇 |
1999年 | 17篇 |
1998年 | 8篇 |
1997年 | 7篇 |
1996年 | 6篇 |
1995年 | 4篇 |
1994年 | 6篇 |
1993年 | 7篇 |
1992年 | 1篇 |
1991年 | 5篇 |
1990年 | 4篇 |
1989年 | 3篇 |
1988年 | 3篇 |
1987年 | 1篇 |
1983年 | 1篇 |
排序方式: 共有271条查询结果,搜索用时 31 毫秒
1.
2.
3.
在合理选择化学Ni-P合金配方和工艺条件的前提下,采用对比试验比较了几种稳定剂对化学镀Ni-P合金镀液及镀层性能的影响,选取合适的工艺参数,采取正交试验方案,研究了KI与其他稳定剂复配时的性能变化规律,探讨了KI的稳定机理。结果表明,备稳定剂之间有的相互兼容、相互促进,有的则相互抵触、相互削弱对方的作用。复合稳定剂综合性能的提高程度明显优于单稳定剂,获得了复合稳定剂KI与Pb(Ac)2质量浓度分别为8g/m^3和1.2g/m^3匹配的最佳工艺参数。 相似文献
4.
Electromechanical actuators (EMAs) are becoming increasingly attractive in the field of more electric aircraft because of their outstanding benefits, which include reduced fuel burn and maintenance cost, enhanced system flexibility, and improved management of fault detection and isolation. However, electromechanical actuation raises specific issues when being used for safety-critical aerospace applications like flight controls: huge reflected inertia to load, jamming-type failure, and increase of backlash with service due to wear and local dissipation of heat losses for thermal balance. This study proposes an incremental approach for virtual prototyping of EMAs. It is driven by a model-based system engineering process in order to enable simulation-aided design. Best practices supported by Bond graph formalism are suggested to develop a model’s structure efficiently and to make the model ready for use (or extension) by addressing the above mentioned issues. Physical effects are progressively introduced, and the realism of lumped-parameter models is increased step-by-step. In particular, multi-level component models are architected to ensure continuity between engineering activities. The models are implemented in the AMESim simulation environment, and simulation responses are given to illustrate how they can be used for preliminary sizing, control design, thermal balance verification, and faults to failure analysis. The proposed best practices intend to provide engineers with fast, reusable, and efficient means to assess performance virtually and enhance maturity, performance, and robustness. 相似文献
5.
6.
汇总了俄罗斯文献中有关机械产品可靠性计算的一些数学公式,并说明了一些公式的适用条件和场合。其中包括:产品输出参数与损伤程度的变化规律,渐发性故障与突发性故障及它们同时出现的过程变化规律,产品参数逼近极限状态与估计等的数学模型。 相似文献
7.
8.
铝合金厚板搅拌摩擦焊焊缝疏松缺陷形成机理 总被引:2,自引:0,他引:2
采用圆锥形搅拌头焊接20mm厚的7075-T6铝板,分析焊接过程中焊缝内部疏松缺陷的形成过程及原因。研究表明,焊缝表面成形良好,无明显缺陷。但是,在焊缝轴肩区和焊核区之间出现了疏松缺陷。分析认为,焊缝上、下部金属温度差太大,导致其塑性流动行为发生变化是疏松缺陷形成的主要原因。搅拌摩擦焊(FSW)过程中,焊缝上部金属温度较高,而底部温度仍然很低,脱离搅拌针端部的塑化金属在周围冷金属巨大的变形抗力作用下转而沿搅拌针表面往上迁移。到达轴肩区下方汇聚区时,由于轴肩区金属温度高,向下的挤压力太小,导致回迁上来的塑化金属继续往上迁移并冲破轴肩区而沿轴肩边缘溢出形成飞边。汇聚区内没有足够的塑化金属填充、焊缝无法被压实而产生疏松孔洞。通过建立疏松缺陷形成的物理模型,可以更直观地反映出焊缝金属流动形态及缺陷形成过程。 相似文献
9.
采用不同工艺参数对TA15钛合金进行电子束焊接,通过观察焊缝形貌、测量其形状参数研究了焊接接头形貌的变化规律,并分析了焊接接头组织。结果表明:增大电子束流时,熔深、半熔深熔宽、焊缝宽度都增大,焊缝横截面的形状从"钉形"转变为"钟罩形";增大焊接速度,对焊缝形状影响不大,熔深、半熔深熔宽及焊缝宽度均减小,深宽比先增大后减小;聚焦电流的增大对熔深作用较明显,半熔深熔宽及焊缝宽度变化不大;扫描幅值的增加使焊缝熔深减小,半熔深熔宽增大。靠近母材的热影响区组织与母材组织相近,主要由初生等轴状α相及转变β相组成,并出现针状(α+β);靠近熔合线的组织由α相和针状(α+β)相构成,并出现α'马氏体;熔合区组织由α'组成,熔合线周围柱状晶垂直于焊缝中心生长,并在焊缝中心形成单列或多列的等轴状晶。 相似文献
10.
进一步研究了先复制后移位桥函数的性质,例如递推关系式、数学表达式、乘积特性及正交条件。同时,还给出了几组完备的正交函数系。 相似文献