Departure Trajectory Design Based on Pareto Ant Colony Algorithm

Due to the ever-increasing air traffic flow,the influence of aircraft noise around the airport has become significant.As most airlines are trying to decrease operation cost,stringent requirements for more simple and efficient departure trajectory are on a rise.Therefore,a departure trajectory design was established for performancebased navigation technology,and a multi-objective optimization model was developed,with constraints of safety and noise influence,as well as optimization targets of efficiency and simplicity.An improved ant colony algorithm was then proposed to solve the optimization problem.Finally,an experiment was conducted using the Lanzhou terminal airspace operation data,and the results showed that the designed departure trajectory was feasible and efficient in decreasing the aircraft noise influence.     

DC Characteristics of Gamma-ray Irradiated SiGe HBT in Comparison with Si BJT

The changes of DC characteristics of SiGe HBT after being submitted to γ-ray irradiation of 700 krad, 7 000 krad and 10 000 krad were compared to those of Si BJT. Generally speaking, Ib and Ib- Ib0 increase with the doses increasing. For SiGe HBT, with the doses increasing, Ic and Ic-Ic0 as well as the related changes of the current gain （β） will decrease at higher Vbe, while for Si BJT, with the doses increasing, after irradiation, Ib and Ic-Ic0 increase; ,8 and its related changes also decrease with their differences, however, tending to be very small at high doses of 7 000 krad and 10 000 krad. Moreover, given the same doses, the decreases of,a are much larger than SiGe HBT, which shows that SiGe HBT＇s anti-radiation performance proves to be better than Si BJT. Still, in SiGe HBT, some strange phenomena were observed： Ic-Ic0 will increase after the radiation of 7 000 krad in less than 0.65 V and as will ,8 in less than 0.75 V. The mechanism of radiation-induced change in DC characteristies was also discussed.     

Robot trajectory planning for autonomous 3D reconstruction of cockpit in aircraft final assembly testing

The trend towards automation and intelligence in aircraft final assembly testing has led to a new demand for autonomous perception of unknown cockpit operation scenes in robotic collaborative airborne system testing. To address this demand, a robotic automated 3D reconstruction cell which enables to autonomously plan the robot end-camera’s trajectory is developed for image acquisition and 3D modeling of the cockpit operation scene. A continuous viewpoint path planning algorithm is proposed that ...     

Influence and optimization of parameters of prepreg viscosity during placement

This paper tested the viscosity of prepreg in the automatic placement process, and conducted the probe and placement-90° peel tests through the test systems. The law of variation of prepreg viscosity during the laying process was studied through these tests under different conditions by taking the peel force to intuitively and quantitatively characterise the viscosity of the prepreg.The results show that this viscosity is inversely proportional to the laying rate, proportional to the laying pres...     

Nonlinear uncertainty quantification of the impact of geometric variability on compressor performance using an adjoint method

Manufactured blades are inevitably different from their design intent, which leads to a deviation of the performance from the intended value. To quantify the associated performance uncertainty, many approaches have been developed. The traditional Monte Carlo method based on a Computational Fluid Dynamics solver(MC-CFD) for a three-dimensional compressor is prohibitively expensive. Existing alternatives to the MC-CFD, such as surrogate models and secondorder derivatives based on the adjoint metho...     

Non-fragile switching tracking control for a flexible air-breathing hypersonic vehicle based on polytopic LPV model

This article proposes a linear parameter varying (LPV) switching tracking control scheme for a flexible air-breathing hypersonic vehicle (FAHV). First, a polytopic LPV model is constructed to represent the complex nonlinear longitudinal model of the FAHV by using Jacobian linearization and tensor-product (T-P) model transformation approach. Second, for less conservative controller design purpose, the flight envelope is divided into four sub-regions and a non-fragile LPV controller is designed for each parameter sub-region. These non-fragile LPV controllers are then switched in order to guarantee the closed-loop FAHV system to be asymptotically stable and satisfy a specified performance criterion. The desired non-fragile LPV switching controller is found by solving a convex constraint problem which can be efficiently solved using available linear matrix inequality (LMI) techniques, and robust stability analysis of the closed-loop FAHV system is verified based on multiple Lypapunov functions (MLFs). Finally, numerical simulations have demonstrated the effectiveness of the proposed approach.     

一种基于大视场星敏感器的定姿方法

根据数学平台失调角随时间变化缓慢的特点,本文提出了一种直接估计数学平台失调角的定姿方法。该方法采用一个20°×20°的大视场星敏器同时观测数颗恒星,并在一小段时间内进行多次观测,所有的测星信息在一次计算中完成对失调角的估计。仿真结果表明,该方法可大大降低星敏感器测量随机误差,其精度明显优于直接估计姿态余弦阵的参考矢量定姿法。     

固体火箭发动机药柱3维应力场光弹性实验研究

应用３维光弹性原理和方法，对３种固体火箭发机的不同星槽翼柱型药的几何尺寸分别进行缩比，模型设计及机加型。然后，把这些模型分别在均匀压强作用下进行应力冻结，切片及应力分析。实验结果表明，实验结果与理论值两者吻合很好。     

Effect of grain refinement on cutting force of difficult-to-cut metals in ultra-precision machining

The nickel-based superalloy Inconel 718 is treated with Coupled Ultrasonic and Electric Pulse Treatment(CUEPT), and the surface grain is refined from the average size of 9550.0 nm to287.9, 216.3, 150.5, 126.3, 25.8 nm by different effective treatment currents, respectively. The ultraprecision turning experiments are carried out on the processed workpiece after CUEPT. The experimental results show that the average cutting force increases with the decrease of surface grain size.Moreover, a mathema...     

Efflcient machining of a complex blisk channel using a disc cutter

For rough machining of a complex narrow cavity, e.g., a complex blisk channel on an aero-engine, the typically used cutting tools are the slender cylindrical cutter and conical cutter.Nevertheless, as neither of the two is particularly suited for rough machining, wherein the main purpose is to remove a large volume as quickly as possible, the machining efficiency is low, especially when the part materials are of hard-to-cut types(e.g., Titanium-alloy) for which it often takes days to rough machi...