排序方式: 共有48条查询结果,搜索用时 15 毫秒
1.
本文用插值摄动法及改进的L-P法相结合的方法求解了一类有限尼的强非线性自由振动问题,得到了一级近似解。 相似文献
2.
提出一种针对大型复合材料机翼结构的二级布局优化策略。系统级根据结构形变调整设计指标,子系统级优化结构布局以满足系统级约束。将机翼壁板中各种临界失效载荷的接近程度作为评判结构效率的标准,通过将结构效率作为优化目标,保证了所求解问题的连续性。加筋壁板通过等效的正交异性板模拟,并根据能量原理预测总体失稳载荷。讨论了加强筋支持弹性对于蒙皮抵抗局部失稳性能的影响,并通过神经网络代理模型对其进行逼近。采用解析模型对失效特性做出评估,减少了计算资源的占用。最后以一种大型机翼结构的综合优化作为算例,计算结果满足设计要求,验证了该方法的可行性。 相似文献
3.
交流阻抗谱法评价热障涂层的热腐蚀行为(英文) 总被引:1,自引:0,他引:1
本文利用交流阻抗这种无损检测的方法研究了热障涂层在质量分数为25%NaCl+75%Na2SO4混合盐体系中的热腐蚀行为。实验结果显示,热腐蚀条件下,在陶瓷层和粘结层界面处形成TGO层为混合氧化物层,成分为Cr2O3、(Ni,Co)(Cr,Al)2O4和NiO,其厚度增长符合抛物线规律。热障涂层在110个循环腐蚀之前时,TGO层的电阻值随其厚度的增加而增加;110个循环后,虽然TGO层的厚度还是在增加,但由于TGO层孔隙的增多而导致其电阻值有所下降。陶瓷层的电阻值随着陶瓷层中裂纹的萌生和扩展而不断增大。等效电路中得到的参数可以用来表征热障涂层的失效行为。 相似文献
4.
Singular formalism and admissible control of spacecraft with rotating flexible solar array 总被引:1,自引:0,他引:1
This paper is concerned with the attitude control of a three-axis-stabilized spacecraft which consists of a central rigid body and a flexible sun-tracking solar array driven by a solar array drive assembly. Based on the linearization of the dynamics of the spacecraft and the modal identi- ties about the flexible and rigid coupling matrices, the spacecraft attitude dynamics is reduced to a formally singular system with periodically varying parameters, which is quite different from a space- craft with fixed appendages. In the framework of the singular control theory, the regularity and impulse-freeness of the singular system is analyzed and then admissible attitude controllers are designed by Lyapunov's method. To improve the robustness against system uncertainties, an H∞ optimal control is designed by optimizing the H∞ norm of the system transfer function matrix. Comparative numerical experiments are performed to verify the theoretical results. 相似文献
5.
挠性太阳帆板驱动控制系统研究 总被引:1,自引:0,他引:1
主要研究了挠性太阳帆板的闭环驱动控制问题.利用挠性结构的模态恒等式,获得了广义状态空间形式的挠性太阳帆板驱动动力学方程.基于Lyapunov方法,设计了基于输出反馈的PD控制器,并根据广义系统理论讨论了闭环系统的正则性和无脉冲性,以确保控制系统是允许的.数值仿真验证了闭环控制算法的有效性并与开环控制进行了比对.最后进行了总结并提出新的研究问题. 相似文献
6.
提出逐次逼近摄动法,将预估的零级近似解逐渐加以修正,使之逐渐逼近于其真实解。有非线性问题的算例。算例表明,解法的精度和其它奇异摄动解法(如L—P法)的基本相同,但方法允许进行一次选代,使其精度更加提高。按照方法,可求得任一级近似解,其精度逐级提高,计算过程也很简便。 相似文献
7.
8.
根据柱面的结构特点,提出了面向柱面复合材料结构的自动铺带四轴联动成形方案,并以卧式自动铺带机为例进行分析。以保证铺放头压力线平行于曲面在铺放点的法线和保证铺放速度恒定为原则,根据D-H理论建立柱面固定角度铺放成形时铺带机各关节运动量的计算方法。应用逆运动学理论,对四轴联动铺带成形进行了运动学分析。从四轴联动铺带机的机构与控制、铺放速度、成形效率、方案可行性4个方面进行了深入分析,并进行可视化仿真和实验验证。结果表明应用本文方法,可实现用四轴联动铺带机完成柱面复合材料自动铺放成形,对于铺放成形效率要求不苛求的小批量实验或生产,具有低成本的突出优势。 相似文献
9.
Deformation Behavior of Medium-strength TA18 High-pressure Tubes During NC Bending with Different Bending Radii 总被引:1,自引:0,他引:1
JIANG Zhiqiang a ZHAN Mei a YANG He a * XU Xudong b LI Guangjun b a School of Materials Science Engineering State Key Laboratory of Solidification Processing Northwestern Polytechnical University Xi’an China b Chengdu Aircraft Industry Corporation Ltd. Chengdu China 《中国航空学报》2011,24(5):657-664
To improve the forming quality and forming limit of the numerical control (NC) bending of high-pressure titanium alloy tubes, in this study, using three-dimensional (3D) finite element method, deformation behavior of medium-strength TA18 high-pressure tubes during NC bending with different bending radii is investigated. The results show that the cross-sectional deformation and the wall thickness variation during NC bending of TA18 tubes using a small bending radius (less than 2 times of tube outside diameter) are clearly different from that using a normal bending radius (between 2 and 4 times of tube outside diameter). For bending with a normal bending radius, with or without a mandrel, the distribution of the flattening in the bending area resembles a platform and an asymmetric parabola, respectively. For bending with a small bending radius, with or without a mandrel, the flattening both distributes like a parabola, but the former has a stable peak which deflects toward the initial bending section, and the latter has a more pronounced peak with a bending angle and deflects slightly toward the bending section. The wall thickness variations with a normal bending radius, with and without a mandrel, both resemble a platform when the bending angle exceeds a certain angle. For the bending with a small radius, the distribution of the wall thickness variation without a mandrel follows an approximate parabola which increases in value as the bending angle increases. If a mandrel is used, the thickening ratio increases from the initial bending section to the bending section. 相似文献
10.
一种机器人砂带磨削的路径规划方法(英文) 总被引:1,自引:1,他引:1
机器人砂带磨削系统具有弹性接触和宽行加工两个显著优点,被广泛应用在具有复杂工件的终加工领域,提高表面质量和加工效率。有关在曲率约束下的磨削路径规划研究较为少见。由于工件与接触轮之间存在复杂的弹性接触,因此,机器人磨削路径可以利用接触运动学的一般方法来求解。机器人砂带磨削过程且需要满足一般的砂带磨削工艺要求,其中最重要的是保证接触轮与工件的局部几何特征贴合。在曲率较小的局部,相邻刀位点的弧长加大,以保证加工效率。相反地,在曲率较大的局部,相邻刀位点的弧长较小,以保证加工精度。利用一系列平面与目标曲面相截,得到相应的截平面的轮廓曲线。对于任意一条轮廓线,优化相邻刀位点之间的弧长,在曲率较大的局部增加一个中间刀位点。本文提出了一种包含弧长优化和主曲率匹配的磨削路径生产方法,通过离线仿真验证了有效性,并利用该方法提高了曲面的磨削质量。该路径规划方法为生成光顺且精确的机器人曲面磨削路径提供了理论依据。 相似文献