In-orbit assessment of laser retro-reflector efficiency onboard high orbiting satellites

The navigation and geodetic satellites that orbit the Earth at altitudes of approximately 20,000 km are tracked routinely by many of the Satellite Laser Ranging (SLR) stations of the International Laser Ranging Service (ILRS). In order to meet increasing demands on SLR stations for daytime and nighttime observations, any new mission needs to ensure a strong return signal so that the target is easily acquirable. The ILRS has therefore set a minimum effective cross-section of 100 million square metres for the on-board laser retro-reflector arrays (LRAs) and further recommends the use of ‘uncoated’ cubes in the arrays. Given the large number of GNSS satellites that are currently supported by SLR, it is informative to make an assessment of the relative efficiencies of the various LRAs employed. This paper uses the laser ranging observations themselves to deduce and then compare the efficiencies of the LRAs on the COMPASS-M1 navigation satellite, two satellites from the GPS and three from the GLONASS constellations, the two GIOVE test satellites from the upcoming Galileo constellation, the two Etalon geodetic spheres and the geosynchronous communications test satellite, ETS-8. All the LRAs on this set of satellites employ back-coated retro-reflector cubes, except those on the COMPASS-M1 and ETS-8 vehicles which are uncoated. A measure of return signal strength, and thus of LRA-efficiency, is calculated using the laser-range full-rate data archive from 2007 to 2010, scaled to remove the effects of variations in satellite range, atmospheric attenuation and retro-reflector target total surface area. Observations from five SLR stations are used in this study; they are Herstmonceux (UK), Yarragadee (Australia), Monument Peak and McDonald (USA) and Wettzell (Germany). Careful consideration is given to the treatment of the observations from each station in order to take account of local working practices and system upgrades. The results show that the uncoated retro-reflector cubes offer significant improvements in efficiency.     

Knowledge Acquisition for ATE Diagnosis

An applied intelligence program for ATE fault diagnosis shows promise as an effective method to reduce mean time to repair (MTTR). The types of knowledge required by an intelligent diagnostic for VLSI test systems, the resources needed to derive that knowledge, the approach implemented to organize it, and the final form of the knowledge representations which resulted from our work are discussed in this paper.     

IMA aircraft improvements

Integrated modular avionics (IMA) is being suggested as the means by which new capabilities can be deployed on aircraft at an affordable cost. RTCA SC-200 is presently considering the guidance document for IMA. All of the functionality that IMA offers can be achieved through a conventional federated architecture; however, the cost, size, and weight penalties of the federated solution make it economically infeasible. IMA is seen as the way forward. It is assuming greater importance as the aircraft industry transitions to commercial-off-the-shelf (COTS) technology with its attendant obsolescence and reliability concerns. IMA may be one of the most cost-effective ways by which rapid obsolescence can be managed. Ironically, this move to COTS is also the greatest threat to IMA systems. IMA achieves reductions in size, cost, and weight by providing a set of flexible hardware and software resources that can be statically or dynamically mapped to a set of required avionics functional capabilities. This introduces a number of new complexities such as mixed criticalities and reconfiguration. We do not address these issues herein. Rather we discuss the mechanisms by which electronics degrades and how a classical safety assessment of a reconfigurable IMA system can be ified by this degradation. We argue that, with the advent of COTS, it is no longer justifiable to consider that electronics has an effectively constant failure rate. Physical considerations suggest that electronics failure occurs when environmental and operating stress causes the accumulation of damage to the underlying structures to exceed the threshold strength of the constituent materials and interfaces. Finally, we suggest how finite-life electronics effects may be mitigated.     

Enhancement and Validation of the IDES Orbital Debris Environment Model

Orbital debris environment models are essential in predicting the characteristics of the entire debris environment, especially for altitude and size regimes where measurement data is sparse. Most models are also used to assess mission collision risk. The IDES (Integrated Debris Evolution Suite) simulation model has recently been upgraded by including a new sodium–potassium liquid coolant droplet source model and a new historical launch database. These and other features of IDES are described in detail. The accuracy of the IDES model is evaluated over a wide range of debris sizes by comparing model predictions to three major types of debris measurement data in low Earth orbit. For the large-size debris population, the model is compared with the spatial density distribution of the United States (US) Space Command Catalog. A radar simulation model is employed to predict the detection rates of mid-size debris in the field of view of the US Haystack radar. Finally, the small-size impact flux relative to a surface of the retrieved Long Duration Exposure Facility (LDEF) spacecraft is predicted. At sub-millimetre sizes, the model currently under-predicts the debris environment encountered at low altitudes by approximately an order of magnitude. This is because other small-size debris sources, such as paint flakes have not yet been characterised. Due to the model enhancements, IDES exhibits good accuracy when predicting the debris environment at decimetre and centimetre sizes. Therefore, the validated initial conditions and the high fidelity future traffic model enables IDES to make long-term debris environment projections with more confidence.     

A Canadian high-energy neutron spectrometry system for measurements in space

Bubble Technology Industries Inc. (BTI), with the support of the Canadian Space Agency, has finished the construction of the Canadian High-Energy Neutron Spectrometry System (CHENSS). This spectrometer is intended to measure the high energy neutron spectrum (approximately 1-100 MeV) encountered in spacecraft in low earth orbit. CHENSS is designed to fly aboard a US space shuttle and its scientific results should facilitate the prediction of neutron dose to astronauts in space from readings of different types of radiation dosimeters that are being used in various missions.