The Origin of Mercury’s Internal Magnetic Field

Mariner 10 measurements proved the existence of a large-scale internal magnetic field on Mercury. The observed field amplitude, however, is too weak to be compatible with typical convective planetary dynamos. The Lorentz force based on an extrapolation of Mariner 10 data to the dynamo region is 10⁻⁴ times smaller than the Coriolis force. This is at odds with the idea that planetary dynamos are thought to work in the so-called magnetostrophic regime, where Coriolis force and Lorentz force should be of comparable magnitude. Recent convective dynamo simulations reviewed here seem to resolve this caveat. We show that the available convective power indeed suffices to drive a magnetostrophic dynamo even when the heat flow though Mercury’s core–mantle boundary is subadiabatic, as suggested by thermal evolution models. Two possible causes are analyzed that could explain why the observations do not reflect a stronger internal field. First, toroidal magnetic fields can be strong but are confined to the conductive core, and second, the observations do not resolve potentially strong small-scale contributions. We review different dynamo simulations that promote either or both effects by (1) strongly driving convection, (2) assuming a particularly small inner core, or (3) assuming a very large inner core. These models still fall somewhat short of explaining the low amplitude of Mariner 10 observations, but the incorporation of an additional effect helps to reach this goal: The subadiabatic heat flow through Mercury’s core–mantle boundary may cause the outer part of the core to be stably stratified, which would largely exclude convective motions in this region. The magnetic field, which is small scale, strong, and very time dependent in the lower convective part of the core, must diffuse through the stagnant layer. Here, the electromagnetic skin effect filters out the more rapidly varying high-order contributions and mainly leaves behind the weaker and slower varying dipole and quadrupole components (Christensen in Nature 444:1056–1058, 2006). Messenger and BepiColombo data will allow us to discriminate between the various models in terms of the magnetic fields spatial structure, its degree of axisymmetry, and its secular variation.     

Missions to Mercury

Mercury is a very difficult planet to observe from the Earth, and space missions that target Mercury are essential for a comprehensive understanding of the planet. At the same time, it is also difficult to orbit because it is deep inside the Sun’s gravitational well. Only one mission has visited Mercury; that was Mariner 10 in the 1970s. This paper provides a brief history of Mariner 10 and the numerous imaginative but unsuccessful mission proposals since the 1970s for another Mercury mission. In the late 1990s, two missions—MESSENGER and BepiColombo—received the go-ahead; MESSENGER is on its way to its first encounter with Mercury in January 2008. The history, scientific objectives, mission designs, and payloads of both these missions are described in detail.     

Current status of the BepiColombo/MMO spacecraft design

This paper shows the current baseline of the conceptual design of the BepiColombo/MMO (mercury magnetospheric orbiter) spacecraft, which is conducted by the ISAS Mercury Exploration Working Group. The MMO is a spinning spacecraft of 200 kg mass whose spin axis is nearly perpendicular to the Mercury orbital plane. The current status of the overall MMO system and subsystems such as thermal control, communication, power, etc. are described. The latest status of the development of critical technologies for the MMO and the outline of the international cooperation between ESA and ISAS are also presented.     

Numerical Simulation of the Ring Current: Review

Numerical simulation of the terrestrial ring current is reviewed. After mentioning ‘modules’ which are needed to be taken into consideration in a ring current simulation, we discuss growth and decay of the ring current. At least four different paradigms have been proposed to account for the ring current development in the past forty years, i.e., the convection paradigm, the substorm paradigm, the diffusion paradigm, and the ionosphere paradigm. As for the proton ring current, a simulation under the convection paradigm gives reasonable results which are in fair agreement with observations with respect to the Dst variation as well as the radial and longitudinal energy density variation of protons when the convection electric field depending on solar wind parameters is given. The proton energy density is observed to be enhanced (weakened) on the nightside, and be weakened (enhanced) near noon during a storm main phase (recovery phase). This characteristic is probably understood to mean that a large-scale and long-standing electric field dominates other electric fields during the storm main phase, e.g., a locally induced electric field (the substorm paradigm) and a highly fluctuated electric field (the diffusion paradigm). The declining of the ring current is shown to be triggered by the decrease in the convection electric field at the beginning of a storm recovery phase, but the decrease in the convection electric field hardly contributes the decay of the ring current. The charge exchange or other loss processes is needed for the substantial decay of it. An ultimate decay rate (several hours) is achieved when the strong diffusion takes place, or when the plasma sheet density drastically decreases while the charge exchange is estimated to provide rather slow decay (a half of day). Diagnosis tools for investigating the ring current, which are expected to bring us a new insight, are proposed in the latter section. This revised version was published online in June 2006 with corrections to the Cover Date.     

Progress of super-pressure balloon development: A new “tawara” concept with improved stability

The super-pressure balloon (SPB) has been expected to be a flight vehicle that can provide a long flight duration to science. Since 1997, we have developed the SPB. Now we are at the phase of developing an SPB of a practical size. In 2009, we carried out a test flight of a pumpkin-shaped SPB with a 60,000 m³ volume. The undesirable result of this flight aroused us to resolve the deployment instability of the pumpkin-shaped SPB, which has been known as one of the most challenging issues confronting SPB development. To explore this deployment issue, in 2010, we carried out a series of ground tests. From results of these tests, we found that an SPB design modified from pumpkin, named “tawara”, can be a good candidate to greatly improve the deployment stability of the lobed SPB.     

A challenge to the highest balloon altitude

Development of a balloon to fly at higher altitudes is one of the most attractive challenges for scientific balloon technologies. After reaching the highest balloon altitude of 53.0 km using the 3.4 μm film in 2002, a thinner balloon film with a thickness of 2.8 μm was developed. A 5000 m³ balloon made with this film was launched successfully in 2004. However, three 60,000 m³ balloons with the same film launched in 2005, 2006, and 2007, failed during ascent. The mechanical properties of the 2.8 μm film were investigated intensively to look for degradation of the ultimate strength and its elongation as compared to the other thicker balloon films. The requirement of the balloon film was also studied using an empirical and a physical model assuming an axis-symmetrical balloon shape and the static pressure. It was found that the film was strong enough. A stress due to the dynamic pressure by the wind shear is considered as the possible reason for the unsuccessful flights. A 80,000 m³ balloon with cap films covering 9 m from the balloon top will be launch in 2011 to test the appropriateness of this reinforcement.     

Lunar Magnetic Field Observation and Initial Global Mapping of Lunar Magnetic Anomalies by MAP-LMAG Onboard SELENE (Kaguya)

The magnetic field around the Moon has been successfully observed at a nominal altitude of ～100 km by the lunar magnetometer (LMAG) on the SELENE (Kaguya) spacecraft in a polar orbit since October 29, 2007. The LMAG mission has three main objectives: (1) mapping the magnetic anomaly of the Moon, (2) measuring the electromagnetic and plasma environment around the Moon and (3) estimating the electrical conductivity structure of the Moon. Here we review the instrumentation and calibration of LMAG and report the initial global mapping of the lunar magnetic anomaly at the nominal altitude. We have applied a new de-trending technique of the Bayesian procedure to multiple-orbit datasets observed in the tail lobe and in the lunar wake. Based on the nominal observation of 14 months, global maps of lunar magnetic anomalies are obtained with 95% coverage of the lunar surface. After altitude normalization and interpolation of the magnetic anomaly field by an inverse boundary value problem, we obtained full-coverage maps of the vector magnetic field at 100 km altitude and the radial component distribution on the surface. Relatively strong anomalies are identified in several basin-antipode regions and several near-basin and near-crater regions, while the youngest basin on the Moon, the Orientale basin, has no magnetic anomaly. These features well agree with characteristics of previous maps based on the Lunar Prospector observation. Relatively weak anomalies are distributed over most of the lunar surface. The surface radial-component distribution estimated from the inverse boundary value problem in the present study shows a good correlation with the radial component distribution at 30 km altitude by Lunar Prospector. Thus these weak anomalies over the lunar surface are not artifacts but likely to be originated from the lunar crustal magnetism, suggesting possible existence of an ancient global magnetic field such as a dynamo field of the early Moon. The possibility of the early lunar dynamo and the mechanism of magnetization acquisition will be investigated by a further study using the low-altitude data of the magnetic field by Kaguya.     

Development of a super-pressure balloon with a diamond-shaped net

The essential reason of the lobed-pumpkin shaped super-pressure balloon to withstand against the high pressure is that the local curvature of the balloon film is kept small. Recently, it has been found that the small local curvature can also be obtained if the balloon is covered by a diamond-shaped net with a vertically elongated shape. The development of the super-pressure balloon using this method was started from a 3-m balloon with a polyethylene film covered by a net using Kevlar ropes. The ground inflation test showed the expected high burst pressure. Then, a 6-m and a 12-m balloon using a polyethylene film and a net using the Vectran were developed and stable deployment was checked through the ground inflation tests. The flight test of a 3000 m³ balloon was performed in 2013 and shown to resist a pressure of at least 400 Pa. In the future, after testing a new design to relax a possible stress concentration around the polar area, test flights of scaled balloons will be performed gradually enlarging their size. The goal is to launch a 300,000 m³ super-pressure balloon.     

Night side lunar surface potential in the Earth’s magnetosphere

In the Earth’s magnetotail, Japanese Moon orbiter Kaguya repeatedly encountered the plasmoid or plasma sheet. The encounters were characterized by the low energy ion signatures including lobe cold ions, cold ion acceleration in the plasma sheet-lobe boundaries, and hot plasma sheet ions or fast flowing ions associated with plasmoids. Different from the previous observations made in the magnetotail by the GEOTAIL spacecraft, the ions were affected by the existence of the Moon. On the dayside of the Moon, tailward flowing cold ions and their acceleration were observed. However, on the night side, tailward flowing cold ions could not be observed since the Moon blocked them. In stead, ion acceleration by the spacecraft potential and the electron beam accelerated by the potential difference between lunar surface and spacecraft were simultaneously observed. These electron and ion data enabled us to determine the night side lunar surface potential and spacecraft potential only from the observed data for the first time.     

Magnetic Cleanliness Program Under Control of Electromagnetic Compatibility for the SELENE (Kaguya) Spacecraft

To achieve the scientific objectives related to the lunar magnetic field measurements in a polar orbit at an altitude of 100 km, strict electromagnetic compatibility (EMC) requirements were applied to all components and subsystems of the SELENE (Kaguya) spacecraft. The magnetic cleanliness program was defined as one of the EMC control procedures, and magnetic tests were carried out for most of the engineering and flight models. The EMC performance of all components was systematically controlled and examined through a series of EMC tests. As a result, the Kaguya spacecraft was made to be very clean, magnetically. Hence reliable scientific data related to the magnetic field around the Moon were obtained by the LMAG (Lunar MAGnetometer) and the PACE (Plasma energy Angle and Composition Experiment) onboard the Kaguya spacecraft. These data have been available for lunar science use since November 2009.