Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

Compression Creep Behavior of High Volume Fraction of SiC Particles Reinforced AI Composite Fabricated by Pressureless Infiltration

The compression creep deformation of the high volume fraction of SiC particles reinforced AI-Mg-Si composite fabricated by pressure-less infiltration was investigated. The experimental results show that the creep stress exponents are very high at temperatures of 673 K, 723 K and 773 K, and if taking the threshold stress into account, the true stress exponent of minimum creep strain rate is still approximately 5, although the volume fraction of reinforcements is very high. The creep strain rate in the high volume fraction reinforced aluminum alloy matrix composites is controlled by matrix lattice diffusion. It is found that the creep-strengthening effect of high volume fraction of silicon carbide particles is significant, although the particles do not form effective obstacles to dislocation motion.     

Fabrication of Diamond-like Carbon Films by Ion Assisted Middle Frequency Unbalanced Magnetron Sputtering

Diamond-like carbon （DLC） films are deposited by the Hall ion source assisted by the mid-frequency unbalanced magnetron sputtering technique. The effects of the substrate voltage bias, the substrate temperature, the Hall discharging current and the argon/nitrogen ratio on the DLC film＇s performance were studied. The experimental results show that the film＇s surface roughness, the hardness and the Young＇s modulus increase firstly and then decrease with the bias voltage incrementally increases. Also when the substrate temperature rises, the surface roughness of the film varies slightly, but its hardness and Young＇s modulus firstly increase followed by a sharp decrease when the temperature surpassing 120 ℃. With the Hall discharging current incrementally rising, the hardness and Young＇s modulus of the film decrease and the surface roughness of the film on 316L stainless steel firstly decreased and then remains constant.     

Gaussian mixture model based adaptive control for uncertain nonlinear systems with complex state constraints

This paper addresses an uncertain nonlinear control system problem with complex state constraints and mismatched uncertainties. A novel Gaussian Mixture Model(GMM) based adaptive PID-Nonsingular Terminal Sliding Mode Control(NTSMC)(GMM-adaptive-PID-NTSMC)method is proposed. It is achieved by combining a GMM based adaptive potential function with a novel switching surface of PID-NTSMC. Next, the stability of the closed-loop system is proved.The main contribution of this paper is that the GMM meth...     

Auroral Electrojet Event Associated With Magnetospheric Substorms

The auroral electrojet index is an important index in monitoring and predicting substorms. A substorms usually includes auroral breakup, auroral electrojet event marked by AE increase, energetic particle injection at geosynchronous orbit, mid-low latitude Pi2, etc. However the question whether an auroral electrojet event corresponds to a substorm remains unanswered. Using the auroral electrojet index in 2004, we analyzed five auroral electrojet events and studied their relation with substorms. The results show that there are three kinds of auroral electrojet events: (1) simultaneous rapid increase of westward auroral electrojet and eastward auroral electrojet; (2) rapid increase of westward auroral electrojet and almost unchangeable eastward auroral electrojet; (3) rapid increase of eastward auroral electrojet and almost unchangeable westward auroral electrojet. Most of auroral electrojet events correspond to substorms. However a few auroral electrojet events are not accompanied by substorms. This situation most often occurs for the auroral electrojet event in which eastward auroral electrojet dominates.      

关于航空工业科研政策与管理若干问题的思考

从科技与经济的结合入笔，探讨了航空工业科研技术创新社会条件的构造和完善，以及创新体制的建设、创新动力机制的建立等问题。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy （P/M） method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10^-6 mm^3/N-m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be prominent.     

无线传感器网络超声波定位算法的研究

在无线传感器网络定位中,距离定位机制受无线传感器设备功耗、价格和硬件限制及对定位精度的要求,距离定位机制比较容易实现的解决方案.介绍了超声波传感器定位的原理,提出了基于传感器数学模型的目标定位方法,在此基础上建立基于超声波的目标定位系统,最后分析了超声波传感器定位中存在的问题.     

强非线性自由振动问题的一种解法

本文用改进了的L－P法研究了一类保守系统强非线性自由振动问题；在此基础上，用插值摄动法[1]进一步研究了更一般的非保守系统的自由振动问题。算例表明，本文方法是可靠的。     

TanSat Mission Achievements: from Scientific Driving to Preliminary Observations

The Chinese global carbon dioxide monitoring satellite (TanSat) was successfully launched in December 2016 and has completed its on-orbit tests and calibration. TanSat aims to measure the atmospheric Carbon Dioxide column-averaged dry air mole fractions (X_CO2) with a precision of 4 ppm at the regional scale, and further to derive the CO₂ global and regional fluxes. Progress toward these objectives is reviewed and the first scientific results from TanSat measurements are presented. During the design phase, Observation System Simulation Experiments (OSSE) on TanSat measurements performed prior to launch measurements using a nadir and a glint alternative mode when considering the balance of stable measurements and reduces the flux uncertainty (64%). The constellation measurements of two satellites indicate an extra 10% improvement in flux inversion if the satellite measurements have no bias and similar precision. The TanSat on-orbit test indicates that the instrument is stable and beginning to produce X_CO2 products. The preliminary TanSat measurements have been validated with Total Carbon Column Observing Network (TCCON) measurements and have inter-compared with OCO-2 measurements in an overlap measurement.