聚四氟乙烯盖板双温区边界条件隔热性能试验设计

针对聚四氟乙烯盖板迎风面和上表面同时满足不同热环境模拟的试验要求,采用有限元方法,对辐射加热试验方案进行了计算分析,重点对加热灯阵高度和遮挡物距离两个影响因素进行了研究。参照计算模拟结果,采用石英灯辐射加热试验设备,对聚四氟乙烯盖板试件进行了隔热性能考核试验,实现了双温区模拟的试验要求。同时试验数据与数值模拟结果吻合度较好,验证了数值模拟方法的可信性和有效性。对于类似隔热材料性能考核试验方法研究具有重要的参考价值。     

石英灯辐射加热试验热流分布优化研究

石英灯辐射加热是在地面上模拟飞行中施加在飞行器表面热载荷的一种加热方式.由于石英灯加热元件的分布不同导致试验件表面不同区域获得的热流密度与要求施加的热载荷有所差异,这样可能会导致"过试验"或"欠试验"现象出现,从而降低了试验数据的可用性,增加了结构设计的风险.本文基于蒙特卡罗方法,对单一石英灯加热器内部热流分布进行了数...     

一种空间用抗原子氧复合膜β布的原子氧、温度、紫外辐射效应的试验研究

在原子氧剥蚀效应地面模拟设备中对一种抗原子氧复合材料β布进行了原子氧剥蚀效应试验、试样湿度升高对原子氧效应的影响试验以原子氧与紫外辐射复合效应试验研究，对试验前后β布试样的质量及表面形貌进行了比较，得出了在材料在设备中的反应特点以及温度变化、紫外辐射对材料的原子氧效应的影响规律。另外对这种材料与原子氧的反应机理进行了分析，得出了一些有意义的结论。     

中段弹道目标的温度场与红外辐射特性计算

红外辐射特性是预警系统探测识别弹道中段目标的重要特征之一。通过计算飞行时目标与太阳、地球的相对位置,确定目标的受外辐射照射状态。利用有限容积法计算锥形目标的三维温度场,采用双向反射分布函数（BRDF）计算目标表面对太阳、地球辐射的反射特性,并结合自身红外辐射,得到了不同类型中段目标红外辐射特性变化情况和空间分布情况。最后,分析了外部辐射环境和目标材料特性对目标红外辐射特性的影响,为中段预警探测提供了参考。     

Improving the orbits of GPS block IIA satellites during eclipse seasons

During Sun-Earth eclipse seasons, GPS-IIA satellites perform noon, shadow and post-shadow yaw maneuvers. If the yaw maneuvers are not properly taken into account in the orbit determination process, two problems appear: (1) the observations residuals increase since the modeled position of the satellite’s navigation antenna differs from the true position, and (2) the non-conservative forces like solar radiation pressure or Earth radiation pressure are mismodeled due to the wrong orientation of the satellite’s surfaces in space.     

SNR periodical variation of Chang'E-3 spacecraft orbiting the Moon

Chang'E-3 spacecraft was orbiting the Moon from December 6–14, 2013, and very long baseline interferometry(VLBI) observations were performed to improve the accuracy of its orbit determination. In the process of recording VLBI raw data, 2 bits quantization was implemented.Interesting phenomenon was that signal-to-noise ratio(SNR) of each VLBI station experienced periodical change and had large variation on amplitude while in the Moon's orbit, whereas SNR kept in a stable level after Chang'E-3 landed on the Moon. Influence of varying elevation angle on SNR was analyzed and compensation of 2 bits quantization harmonics to SNR calculation was investigated. Most importantly, telescope system noise temperature increase caused by the Moon was computed along the time of Chang'E-3 orbiting the Moon, and well matched SNR changing trend in terms of correlation coefficients.     

Study of a Coronal Mass Ejection with SOHO/UVCS and STEREO data

We study the 3-D kinematics of a Coronal Mass Ejection (CME) using data acquired by the LASCO C2 and UVCS instruments on board SOHO, and the COR1 coronagraphs and EUVI telescopes on board STEREO. The event, which occurred on May 20, 2007, was a partial-halo CME associated with a prominence eruption. This is the first CME studied with UVCS data that occurred in the STEREO era. The longitudinal angle between the STEREO spacecrafts was ∼7.7° at that time, and this allowed us to reconstruct via triangulation technique the 3-D trajectory of the erupting prominence observed by STEREO/EUVI. Information on the 3-D expansion of the CME provided by STEREO/COR1 data have been combined with spectroscopic observations by SOHO/UVCS. First results presented here show that line-of-sight velocities derived from spectroscopic data are not fully in agreement with those previously derived via triangulation technique, thus pointing out possible limitations of this technique.     

一体化红外抑制器遮挡和出口修型对后机身表面温度和红外辐射特性的影响

针对与后机身融合的一体化红外抑制器模型,采用数值模拟的方法研究了内部遮挡和出口修型对后机身表面温度场和红外辐射特性的影响。在混合管外部采用遮挡套或曲面遮挡板可有效降低后机身侧壁面对应混合管后段的局部区域最高温度,两种方式均可有效降低水平探测面以及铅垂面上方3~5 μm波段和8~14 μm波段红外辐射强度峰值;然而,加装遮挡套方式会影响旋翼下洗气流的导入,使3~5 μm波段的红外辐射强度在铅垂面下方较基准模型有小幅的增加。对后机身排气口进行出口修型,虽然对降低后机身3~5 μm和8~14 μm波段红外辐射强度的作用效果并不显著,但可以有效消除排气出口下方壁面的高温区,其中采用狭窄流道引气冷却方式可以使得后机身侧壁仅高于环境温度10 K左右。     

管道惯性测量系统散热仿真分析

基于FLUENT商用软件建立了在60℃高温油内使用的管道惯性测量系统的传热数值模型,模拟了系统在自然对流、不同风冷强制对流和不同热辐射系数下散热的温度分布,分析了风扇布置、空气流量及结构件表面热辐射系数对系统温度分布的影响.通过仿真分析取得了系统有效的散热配置,试验验证结果与仿真计算情况基本吻合,两者相差1.1％.     

星载二次电源的电磁兼容预设计

针对星载二次电源电磁兼容试验中辐射发射的超标问题,提出了电磁兼容预设计方法.分析二次电源电磁干扰产生的机理,利用SPICE仿真器建立传导干扰的电路等效模型,优化电路设计得到传导干扰源;应用修正的单线模型近似计算辐射干扰,根据计算结果,利用遗传算法优化等效偶极子的数目和分布位置建立场等效模型;基于场路结合的方法,以传导干...