A non-local vectorial total variational model for multichannel SAR image speckle suppression

This paper aims at the multichannel synthetic aperture radar(SAR)image speckle reduction.This paper proposes a novel energy minimized regularization model for multichannel image denoising,which is an extension of the non-local total variational model for gray-scale image.It contains two terms,namely the vectorial data fidelity term and the non-local vectorial total variation term.The latter is constructed by high-dimensional non-local gradient that contains the structure information of the multichannel image.The existence and the uniqueness of the solution of the model are proved.A fixed point iterative algorithm is designed to acquire the solution of this model.The convergence property of this algorithm is proved as well.This model is applied to the multipolarimetric and multi-temporal RADARSAT-2 images despeckling.The result shows that this model performs better than the original vectorial total variational model on texture preserving.     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.     

椭圆形切扇修形对波瓣混合器掺混性能影响

在保证面积不变的情况下,选取不同的长轴、短轴,对波瓣混合器进行椭圆形切扇修形,研究切口深度与宽度对波瓣混合器掺混性能的影响规律。使用商用 CFD 软件对流场进行数值模拟。结果显示,对波瓣侧壁进行切扇处理会加强流向涡的强度,切扇越深,流向涡强度越大;切扇波瓣流向涡的耗散速率要大于基准波瓣混合器的流向涡耗散速率,预示着更为高效的掺混;引射系数与切口深度成正比,而总压恢复系数与切口深度成反比。考察了两种衡量热混合效率的模型并对其信度进行了比较,发现在 x =0.4 m 之前切扇可以提高热混合效率,而在 x =0.4 m 之后,基准波瓣混合器热混合效率要大于切扇波瓣混合器。     

Stability analysis of an aeroelastic system with friction

In this paper, harmonic balance method, exact formulation and numerical simulation method are adopted to study the effects of different friction stiffness on the stability of 1.5 degrees of freedom aeroelastic system. On this basis, the expressions of input energy and dissipated energy are deduced, and the energy method is used to reveal the mechanisms of the stable boundary and unstable boundary existing in the system and the effects of different friction stiffness on the stability of the system. Studies have shown that the stability region and the critical aerodynamic damping ratio of the system rise with the increase of the friction stiffness, while the friction stiffness has little effect on the stability boundary. In the analysis of the stability of system, the results of harmonic balance method, exact formulation and Newmark of numerical simulation method are in good agreement. Compared with exact formulation and numerical simulation method, the concept and conclusion of harmonic balance method are simple in the system stability analysis.     

一种实现陀螺马达准确制动方案的研究

在分析了几种传统的电机制动方案基础上,提出了一种适合陀螺马达的能耗制动方案,该方案依据马达逐渐停转时自身产生的微弱电信号,再经放大处理后作为能耗制动的控制信号,实现陀螺马达准确、可靠、平稳的停止,避免了不及时切断电源而烧坏定子绕组的情况.     

GaInP2外延膜中施主—受主对复合发光带的能量关量

通过变温与变激发强度的近红外光致发光研究了用ＭＯＣＶＤ方法、生长在ＧａＡｓ衬底上的Ｇａ０．５Ｉｎ０．５Ｐ（ＧａＩｎＰ２）外延薄膜的１．１７ｅＶ发射带的发光特性。１．１７ｅＶ发光带性质与０．９９ｅＶ及０．８５ｅＶ发光带的性质有着明显的差别。１．１７ｅＶ发光带的机理可用施主－受主对的复合发光来解释，其中施主－受主对系白处在Ｇａ格位上的Ｓｉ（ＳｉＧａ）及其最邻近的Ｇａ空位（ＶＧａ）所组成，记作ＳｉＧａ－ＶＧａ。考虑到ＧａＩｎＰ２中存在着很强的电子－格子耦合作用及其Ⅲ族子格子为部分有序，所以在施主－受主对复合发光中应计及Ｆｒａｎｃｋ－Ｃｏｎｄｏｎ位移△ＦＣ及该对在等效的部分有序势场中的相互作用能Ｅｓ（ＤＡＰ）。Ｘ—射线衍射实验表明，部分有序结构相当于成分调制，因而可用Ｋｒｏｎｉｇ－Ｐｅｎｎｅｙ模型来计算Ｅｓ（ＤＡＰ）值。这样，我们就导出了施主－受主对复合发光的新的能量表示式。     

关于跨声速流动问题的多重解

本文讨论了跨声速流小扰动方程Riemann问题的多重解及物理上可实现的解的判别。     

基于的DTV图像去噪模型

针对纹理图像的去噪问题,通过分析全变分（TV）去噪模型与方向全变分（DTV）去噪模型,提出了一种具有鲁棒性的基于的DTV去噪模型。为了刻画图像中的不同结构特征,该模型中DTV正则项的指数p由图像的结构来确定在（0,2）中自适应地选取。由于该模型是含有可分性算子的非光滑优化问题,可用交替方向乘子法（ADMM）求解,并能保证算法的收敛性。数值实验结果表明:与其他经典模型相比,提出的模型取得了更高的峰值信噪比和结构相似度,在去除噪声的同时能有效保持图像的细节信息。      

Analysis on Output Power for Multi-direction Piezoelectric Vibration Energy Harvester

To predict the performance of multi-direction piezoelectric vibration energy harvester,an equation for calculating its output power is obtained based on elastic mechanics theory and piezoelectricity theory.Experiments are performed to verify theoretical analysis.When the excitation direction is along Y direction,a maximal output power about 0.139 mW can be harvested at a resistive load of 65kΩ and an excitation frequency of 136 Hz.Theoretical analysis agrees well with experimental results.Furthermore,the performance of multi-direction vibration energy harvester is experimentally tested.The results show that the multi-direction vibration energy harvester can harvest perfect energy as the excitation direction changes in XY plane,YZ plane,XZ plane and body diagonal plane of the harvester.     

Energy principle and material removal sequence optimization method in machining of aircraft monolithic parts

In the machining process of aircraft monolithic parts, the initial residual stress redistribution and structural stiffness evolution often lead to unexpected distortions. On the other hand, the stress redistribution and stiffness reduction during the machining process depend on the material removal sequence. The essence of the stress redistribution is releasing the initial elastic strain energy. In the present study, the influence of the material removal sequence on the energy release is studied. Moreover, a novel optimization method is proposed for the material removal sequence. In order to evaluate the performance of the proposed method, the mechanism of the machining distortion is firstly analyzed based on the energy principle. Then a calculative model for the machining distortion of long beam parts is established accordingly. Moreover, an energy parameter related to the bending distortion and the procedure of the material removal sequence optimization is defined. Finally, the bending distortion analysis and material removal sequence optimization are performed on a long beam with a Z-shaped cross-section. Furthermore, simulation and experiments are carried out. The obtained results indicate that the optimized sequence results in a low distortion fluctuation and decreases the bending distortion.