风挡防冰表面温度场计算

在研究国内外有关资料的基础上，采用了量纲分析的方法，建立了风挡外表面温度场的计算模型。回避了对自由流与射流相互干扰这一复杂问题的研究，同时对该计算模型进行了验证，并开发了相应的计算程序。该问题的解决，填补了国内在该领域中的空白。     

脉冲式转速表的设计,校验与应用

本文就航空发动机转速测量技术状态进行了简要分析,对适用于超轻型飞机的具有原理、结构简单,造价低等优点的“脉冲式转速表”的设计、校验等进行了详细的论述,并对该原理的推广应用进行了分析讨论。     

三维瞬态导热温度场边界元计算及一阶数学奇异的处理

推导了三维瞬态导热温度场边界元解法的积分方程和离散代数方程，并编制了相应的计算机程序，采用坐标变换的解析消去法，处理边界元的一阶数学奇异点，从而提高了算法的数值精度。用本程序计算了正方体和圆柱环瞬态导热温度场，数值解与解析解的吻合程度令人满意。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

钛合金板材激光弯曲成形的研究

 对常温下钛合金板材进行了激光弯曲成形研究。分析了激光功率、扫描速度、光斑大小对板材弯曲变形的影响,获得理想工艺参数范围为:功率1 .0～1 .2 k W、扫描速度2～3 m/min、光斑直径6～7mm。同时分析了板材厚度、宽度及扫描次数对材料弯曲变形的影响,为钛合金板材弯曲成形提供了一种新途径。     

双温度试验系统方案设计

结合双温度试验系统方案设计,介绍了可编程控制器在温度控制上的应用,有助于增进读者对PLC等的了解。     

生态环境材料——社会可持续发展的物质基础

 生态环境材料是近年来在先进材料研究中提出的一个新研究领域。简要介绍了生态环境材料概念的产生、发展及哲学基础,从材料环境协调性评价、材料和物质的再生循环、与生态系统相协调的材料与工程、环境工程材料、与材料科学相关的生态工程等几方面对生态环境材料研究的最新进展进行了评述。     

热暴露对IMI834近α高温钛合金组织和拉伸性能的影响

测试了ＩＭＩ８３４高温钛合金在６００～７５０℃的空气中热暴露１００小时后拉伸性能，利用透射电镜和扫描电镜观察了合金暴露前后的组织变化及拉伸断口，认为表面氧化是造成合金热暴露后塑性下降的主要原因，但基体组织内有序α２相和硅化物的析出变化也在不同程度上造居了合金热暴露后的强度和塑性的下降。     

机载小惯量探针研制及在飞机武器发射中的应用

介绍了一种用于飞机武器发射时测量发动机进口动态温升时序的机载小惯量探针,以其独特的研制方法,较好地解决了机载小惯量测温装置、频响与可靠性兼顾这一测试难题,并在武器发射时,成功地用来评价发动机工作稳定性的影响。     

Microstructure and Martensitic Transformation Behaviors of Explosively Welded NiTi/NiTi Laminates

The study is a first attempt to prepare bulk NiTi/NiTi shape memory alloy (SMA) laminates with a macroscopic heterogeneous composition by explosive welding and investigate their microstructures and martensitic transformation behaviors. After explosive weld- ing, a perfect interfacial bonding between the two components and a reversible martensitic transformation are realized in the tandem. Results show achievement of a fine granular structure and the maximum value of microhardness near the welding interface because of the excessive cold plastic deformation and the high impact velocity during the explosive welding. Meanwhile, the effects of aging on the transformation of the welded tandem are investigated by differential scanning calorimeter (DSC) and subject to discussion. The trans- formation temperatures of NiTi/NiTi SMAs increase with the rise of the aging temperature. The experimental results indicate the shape memory properties of NiTi/NiTi SMA fabricated by explosive welding can be improved by optimizing the aging technology.