Experimental Investigation of Nozzle Effects on Thrust and Inlet Pressure of an Air-breathing Pulse Detonation Engine

Nozzle effects on thrust and inlet pressure of a multi-cycle air-breathing pulse detonation engine (APDE) are investigated experimentally. An APDE with 68 mm in diameter and 2 050 mm in length is operated using gasoline/air mixture. Straight nozzle, converging nozzle, converging-diverging nozzle and diverging nozzle are tested. The results show that thrust augmentation of converging-diverging nozzle, diverging nozzle or straight nozzle is better than that of converging nozzle on the whole. Thrust augmentation of straight nozzle is worse than those of converging-diverging nozzle and diverging nozzle. Thrust augmentations of diverging nozzle with larger expansion ratio and converging-diverging nozzle with larger throat area range from 20% to 40% on tested frequencies and are better than those of congeneric other nozzles respectively. Nozzle effects on inlet pressure are also researched. At each frequency it is indicated that filling pressures and average peak pressures of inlet with diverging nozzle and converging-diverging nozzle with large throat cross section area are higher than those with straight nozzle and converging nozzle. Pressures near thrust wall increase in an increase order from without nozzle, with diverging nozzle, straight nozzle and converging-diverging nozzle to converging nozzle.     

内并联型TBCC进气道方案设计及验证

提出了一种带可变几何泄流腔的内并联型涡轮基组合循环(TBCC)进气道设计方案.介绍了进气道的总体设计思路,给出了进气道的设计马赫数、转级马赫数及飞行轨迹,对不同来流条件下进气道的工作方式以及全马赫数范围进气道型面调整的安排进行了论述,确定了进气道主要气动参数与型面参数的选取原则.通过数值模拟和高速风洞试验的手段,对进气道设计方案的可行性进行了验证.数值模拟结果表明:当Ma₀≤2.5时,进气道的总压恢复系数均在0.8以上,当2.5<Ma₀≤4.5时,进气道的总压恢复系数均在0.3以上,符合进气道总体方案的要求;冲压模态下,冲压通道的出口马赫数均小于0.4,出口静压均大于0.5个标准大气压,均能满足冲压燃烧室的燃烧需求.风洞试验结果表明:模态转换过程中,进气道涡轮通道具有良好的进/发匹配特性,且进气道涡轮/冲压通道具有良好的相容性能.研究结果可为我国开展组合动力研究提供方案参考和技术储备.      

射流对高超声速进气道起动性能的影响

为探索利用射流技术降低进气道起动马赫数的可行性,对二元高超声速进气道二维流场进行了数值模拟,通过对比不同工况的流场结构、流量系数及总压恢复系数,分析了射流对高超声速进气道的作用效果,并研究了射流速度、压强及倾角对进气道起动性能的影响。分析结果表明:施加射流,激波与进气道边界层原有干扰形式发生改变,是降低进气道起动马赫数的主要原因。研究还表明,增大射流速度利于提高控制效果,但持续增大射流速度,会造成隔离段反压升高,并且这一现象与射流压强相关,降低射流压强能使进气道起动的射流速度区间扩大,同时在不同射流倾角下,上述规律表现一致。该研究揭示了进气道起动能力随射流参数变化的系统性规律,可用于指导工程设计及优化。     

提高固定几何二元进气道低马赫数性能的仿真研究

分别以常规低、高马赫数来流设计的固定几何二元混压式进气道为例,采用数值模拟手段,探究了一种改进的外压缩波系配置方案。采用来流马赫数由低到高,外压缩激波依次封口的设计方法,提高了固定几何二元进气道的低马赫数性能。相比常规配波设计的进气道,来流马赫数2.15条件下的流量系数提高了0.07;来流马赫数2.15和2.4条件下,总压恢复提高近0.015。初步研究证明这种设计理念是合理的,该设计方案有待于进一步发展和实验验证。     

Numerical simulation of the three-dimensional flow-path in a ram-rotor

A kind of three-dimensional flow-path of the ram-rotor was designed in this paper according to the design method of the typical supersonic intake of aircraft and missiles,especially the design method of the compression ramp,the throat and the subsonic diffuser.The design Mach number of the flow-path was based on the averaged relative Mach number,regardless of the change of incoming Mach number along radial direction of the flow-path.Then,the flowfield of the designed flow-path was simulated numerically with computational fluid dynamics software at design point.The purpose of simulation was to obtain the details of the flowfield,including the structure of the shock wave system,position of flow separation zone,and so on.The performance of the ram-rotor was also evaluated.The numerical results show the structure of the shock wave system in the flow-path is similar to that in the supersonic intake.To improve the overall performance of the ram-rotor,the reasonable compromise between the total pressure ratio and the isentropic adiabatic efficiency should be reached.The structure optimization of the flow-path and the configuration of the shock wave system have great influence on the performance of the ram-rotor.      

内并联式TBCC进气道模态转换过程流动特性分析

针对组合动力(TBCC)进气道模态转换过程中出现的非定常气动现象,采用稳态/非稳态数值模拟方法对相关流动特性及其影响因素与流动机理开展了研究。结果表明：由涡轮发动机工作状态向冲压发动机工作模态转换过程中,进气道内出现结尾激波沿流向前后振荡现象,振荡频率约为130Hz;当冲压流道反压引起的激波未前传至模态转换分流板前时,冲压发动机工作状态对结尾激波振荡不产生影响。在相同的发动机工作状态下,随着模态转换速度的增加,结尾激波振荡频率逐渐增大。文中研究的进气道内结尾激波振荡现象可通过亚声速管道内波的传播理论进行解释和分析。     

边界层对可调节进气道性能的影响

给出了马赫数2-6、单位雷诺数（0．8-6．0）×10^7／m时下吹式风洞中可调节三维进气道的试验研究结果。研究了前缘前掠和后掠方案以及进气道人口前边界层的影响。测量了内流道内的压力分布、质量流量和总压恢复系数;确定了进气道启动与马赫数和流动工况的关系。研究结果表明：边界层对流场结构和模型进气道的性能有着决定性影响,相对简单的进气道调节方案可以增大其稳定运行范围。     

蛇形进气道涡控设计研究

针对传统概念设计的蛇形进气道畸变大、总压恢复系数较低以及相应流场控制技术存在局限性等缺点,对典型蛇形进气道内通道二次流的涡动力学形成及其对气流分离影响分析的基础上,提出了蛇形进气道涡控设计概念,并利用数值仿真进行了初步验证.仿真结果表明:与原型方案相比,蛇形进气道涡控设计方案成功抑制了上壁面大范围的气流分离,巡航状态畸...     

双管爆轰单引射增推机理的数值研究

基于二维Euler方程,结合高精度Roe/HLL(Harten-Lax-Van Leer)混合格式与自适应网格加密技术,对引射模态下的双管爆轰非定常单次引射复杂流场进行了数值模拟.结果分别描述了方管爆轰波喷出及引射管内二次爆轰波的传播过程.双爆轰波喷出爆轰管后,以欠膨胀射流形式向外传播,同时,它们相互作用延长了引射管尾...     

高超声速进气道附面层分离无源被动控制

为了控制超燃冲压发动机进气道唇口反射激波诱导的附面层分离,根据其流动特征,提出了附面层泄除-吹除互相驱动的自适应、无源、被动控制方案。并采用空间HLLE格式、LU-SGS隐式推进、多块结构网格的有限体积法数值模拟程序对该流动现象进行了数值模拟。数值结果表明,施加自适应无源被动控制后,分离区长度减小为无控制时的45%,控制区域的总压恢复系数和流场均匀性提高。从而证实了自适应、无源、被动控制抑制高超声速进气道附面层分离的可行性。