Spectroscopy peculiarities of thermal plasma of electric arc discharge between electrodes with Zn admixtures

Plasma of the free burning electric arc between Ag–SnO₂–ZnO composite electrodes as well as brass electrodes were investigated. The plasma temperature distributions were obtained by Boltzmann plot method involving Cu I, Ag I or Zn I spectral line emissions. The electron density distributions were obtained from the width and from absolute intensity of spectral lines. The laser absorption spectroscopy was used for measurement of copper atom concentration in plasma. Plasma equilibrium composition was calculated using two independent groups of experimental values (temperature and copper atom concentration, temperature and electron density). It was found that plasma of the free burning electric arc between brass electrodes is in local thermodynamical equilibrium. The experimental verification of the spectroscopic data of Zn I spectral lines was carried out.     

热处理对FeCo-2V-0.5Cr软磁合金力学与磁学性能的影响

针对FeCo-2V-0.5Cr软磁合金,研究了真空热处理时间对其微观组织结构、力学与磁学性能的影响规律,发现在800℃下热处理时间为2h左右时,合金的抗拉强度和延伸率达到最佳,同时仍保持良好的软磁性能,抗拉强度、延伸率以及矫顽力分别为867.8MPa、10.4%以及2.0Oe。进一步对该合金进行附加磁场下的真空热处理,重点研究了合金的交流损耗与矫顽力随附加磁场方式包括磁场撤除温度与磁场下保温时间的变化规律,发现适当的磁场热处理对合金相关力学性能影响不大,但由于合金中产生了单轴各向异性而使合金矫顽力进一步降至1.6Oe。     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

野战环境下大型飞机超低空气动特性分析

针对野战环境下的大型飞机超低空飞行,采用CFD方法对地面存在前向或横向不对称障碍物时地面效应对气动参数的影响进行了数值分析,包括纵向稳定性和侧向摇晃等问题.研究结果表明,野战等非常规飞行条件下,地面不确定障碍物会造成大型飞机稳定性变差,严重时可能出现纵向点头和横侧向摇晃现象,容易导致触地危险.最后,从现代飞行控制理论角度提出了对常规布局大型飞机进行闭环控制的研究思路.     

复合材料构件热压罐成型温度场研究

在热压罐固化工艺的热历程中,复合材料零件表面温度场分布的合理与否将直接决定产品的固化质量.以工字型零件和T型加筋壁板两种复合材料零件为研究对象,使用EC-3×8M和SCH-5.5×21M两种型号热压罐,同时选择炉温偶和零件偶两种控温方式对零件进行固化.通过分析温度场测试结果发现,控温方式、设备加热方式、升降温速率、热电偶的摆放位置、固化压力等因素均对零件的温度场有影响.     

TC4钛合金静止轴肩和传统搅拌摩擦焊的温度场对比

基于有限元软件ABAQUS对6mm厚的TC4钛合金传统及静止轴肩搅拌摩擦焊温度场进行了有限元模拟.结果表明,对比传统搅拌摩擦焊接,静止轴肩搅拌摩擦焊接具有较小的高温区,前进方向上具有较大的温度梯度,厚度方向上呈现柱状椭球形分布,上、下表面温度峰值差异较小,具有重叠性较好的热循环曲线.     

RFID技术在航空领域的应用研究

射频识别(RFID)技术现已广泛用于物流、金融、零售等各个行业.航空领域的RFID应用起步较晚,通过对RFID技术在飞机制造商、原始设备生产厂家(OEM)、航空公司的一些典型的应用案例的分析,提出RFID技术应用于航空领域所面临的挑战及必要性,为其未来航空业自动识别技术的发展指明了方向.     

跨声速串列转子失速机制的数值研究

为了解决跨声速串列转子的低裕度问题,就必须了解跨声速串列转子的流场结构与失速机制.设计了叶尖切线速度为450m/s,负荷系数为0.56的高负荷跨声速串列转子.基于数值模拟的结果,分析了该串列转子在0.5mm叶尖间隙下的叶尖流场结构与失速机制,并在此基础上分别探讨了叶尖间隙和前、后排叶片周向位置对串列转子特性的影响和失速机制的变化.结果表明:前排叶片的叶尖区域是 影响串列转子稳定性的关键;随着叶尖间隙的增加,串列转子的失速机制也发生变化,从前排叶片叶尖区域的尾迹与径向潜流堵塞后排叶片通道转变为前排叶片叶尖泄漏流堵塞;在较大周向相对位置(后排叶片压力面周向远离前排吸力面)的情况下,串列转子获得最好的效果,随着周向相对位置(PP)的增加,失速部位从后排叶片转移至前排叶片.      

液化天然气作为航空燃料的发展趋势及特点分析

为研究液化天然气(LNG)作为航空燃料的可行性,对LNG的特点、发展趋势及作为航空燃料存在的问题进行了分析.采用了横向比较的方法,将LNG与新的航空替代燃料和传统航空燃料进行了比较和计算分析.结果表明:与新的航空替代燃料相比,LNG具有来源广泛、经济性好、发动机适应性强等优点.与传统航空燃料相比,LNG的储量大,可使用100年以上;可燃极限宽、污染物排放低,NOx排放仅为航空煤油的1/4;单位质量能量密度高、成本低,其燃料成本仅为航空汽油的一半,航空煤油的1/3;同时还具有可用于发动机高温部件冷却用的冷能,是一种极富潜力的航空燃料.指出在LNG作为航空燃料方面急需开展动力系统与飞机结构的匹配、燃料相态的有效转化及不同燃料在燃烧室内的反应特性等方面的研究工作.      

温度对飞机燃油射流泵工作特性影响

建立了射流泵数学模型,采用数值计算方法对其工作特性进行了模拟,搭建了实验台,采用RP-3燃油,通过实验数据验证了模型的正确性.在此基础上,分别选择了RP-3和JET-A两种燃油,计算了从-40℃~40℃温度下,不同操作压力对射流泵流量比的影响.结果表明:燃油温度高于0℃时,温度对射流泵工作特性影响并不明显,随着温度的降低,射流泵性能与标准温度下（20℃）偏差越来越大,且压比越高此偏差越明显.当温度高于0℃时,采用RP-3和JET-A燃油性能相差不大,RP-3燃油性能略优于JET-A燃油,但是在低温下,RP-3燃油性能远高于JET-A燃油.因此当燃油温度较低且压比较高时,必须充分考虑温度对射流泵特性的影响.