轴对称结构RBCC发动机超燃模态试验和数值模拟

为研究轴对称结构RBCC发动机超燃模态下的点火和燃烧性能,进行了地面直连试验。采用中心支板火箭与小支板组喷注相结合的方式作为点火和火焰稳定方式,并对燃料喷注方案进行了研究。试验与数值模拟结果表明,采用这种点火方式能实现轴对称结构RBCC发动机的可靠点火和稳定燃烧。二次燃料采取多级喷注的方式能充分利用流道中的氧气,实现较充分的燃烧,但应控制燃料喷注比例。双支板组的加入,能促进燃料与中心空气流的充分掺混,提升燃烧效率,获得较优的燃烧性能。     

高超声速飞行器-进气道一体化热流数值计算

采用CFD(计算流体动力学)技术, 开展了飞行器前体/发动机一体化气动热环境分析.对层流区、转捩区和湍流区分别采用计算模型, 在湍流区利用压缩性修正的SSGZ-Jk-ε湍流模型, 在转捩区引入代数型转捩因子模型描述边界层由层流逐渐过渡为完全湍流的流动过程.计算了前体和内通道的表面热流, 并与实验结果进行了对比.结果表明所采用的计算方法可以较好地预测前体及发动机内通道热流率, 流动状态、几何结构及激波入射对热流值影响较大.      

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

凹腔火焰稳定器阻力特性的实验研究

在超燃冲压发动机直连式实验中,模拟马赫数1.92、静温509K、静压86.6kPa来流,采用等截面燃烧室构型,利用推力测量系统对不同结构尺寸的开式凹腔火焰稳定器的冷流阻力和热试阻力进行了研究。通过对深度分别为10,15,20mm,长深比4~10,后壁倾斜角18°~60°的凹腔火焰稳定器的冷流阻力比较,实验表明凹腔火焰稳定器的冷流阻力与凹腔深度成正比;也与凹腔长深比成正比;并随后壁倾斜角的增大先减小后增大,在30°~60°范围内应存在一个角度使得冷流阻力最小。实验还以氢气为燃料,利用火花塞点火器进行点火,在燃烧模态下对不同喷注位置、不同当量比时的凹腔火焰稳定器阻力特性进行了对比,结果表明凹腔火焰稳定器的热试阻力比冷流阻力小,且受燃料喷注方式的影响较大;在实际超燃冲压发动机工况下,凹腔火焰稳定器的阻力随着当量比的增加而减小,并最终会表现为正推力。     

超燃冲压发动机缩比燃烧室流场数值模拟

为了采用二维N-S方程来研究带有垂直喷射的三维问题,即拓展二维模型的适用范围,提出了一种针对喷射的简化模型,即采用源项加质来近似模拟喷射的质量添加。为了验证这种简化的可行性,针对文献中的实验条件进行了对比计算。结果表明,数值模拟与实验点符合得较好。运用以上简化模型,对放置在自由射流实验台上的缩比超燃冲压发动机燃烧室流场,采用五组元单步反应模型进行了数值模拟,得到了各主要气动参数及组分质量分数的分布,表明,根据数值模拟所得到的壁面静压值与实验壁面压力符合得较好。      

湍流燃烧模型对氢燃料超燃室流场模拟的影响

采用化学平衡的假定概率密度函数(PDF)模型和火焰面模型计算了德国宇航研究中心的超燃室反应流,计算结果与有限速率反应模型的和实验的结果进行了对比.使用有限体积法离散Favre平均的N-S方程,湍流模型采用k-ε模型.研究表明:(1)有限速率反应模型在喷氢孔近场,化学平衡的假定PDF模型在喷氢孔远场不能准确捕捉流场的细致结构,而火焰面模型对全流场预测较好,后两种模型的计算时间较有限速率反应模型节省约38%;(2)超燃室内湍流和燃烧相互作用不可忽略,从预测精度和计算效率来看,火焰面模型有较好的工程应用前景.      

一种基于双模态燃烧二元高超声速进气道研究

设计并研究了一种基于双模态燃烧的二元高超声速进气道.通过在进气道内设计一个隔板,将流道分为超声速通道和亚燃通道.采用数值模拟方法,研究了内压段肩部型面,隔板进口高度及水平位置,过渡段起始点及扩张角、下通道出口高度、隔板头部型面等几何设计参数对进气道性能的影响规律,并给出了参数选择建议.结果表明:在研究范围内,内压段肩部型面、隔板进口高度及水平位置和过渡段起始点对总压恢复系数影响较大;而隔板进口高度及头部型面、过渡段扩张角和下通道出口高度对抗反压能力有较大影响.      

Influence of fuel injection position and equivalent mixture ratio on chemical non-equilibrium effects of single expansion ramp nozzle

Chemical non-equilibrium flow was investigated for the scramjet single expansion ramp nozzle(SERN) with a strut-based liquid-kerosene-fueled combustor.Two-dimensional Reynolds-averaged Navier-Stokes(RANS) equations were solved with the species conservation equation for continuous phase and the renormalization group(RNG) k-ε turbulence model.Lagrangian discrete-phase model was analyzed for liquid-kerosene droplets behavior in the supersonic stream.Combustion was simulated by kerosene surrogate fuel's 10-species and 13-step reduced reaction kinetics mechanism with use of Arrhenius's laminar finite rate model.Parametric studies were carried out to estimate the influence of different fuel injection positions and equivalent mixture ratios on the SERN chemical non-equilibrium effects.Numerical calculation results show that the strut-based combustor enables convenient modeling of various SERN entry conditions,which is similar with many preceding investigations,by changing the injector strut position and controlling the mass flow rate of each injector.Chemical non-equilibrium effects function in the whole SERN,especially in the initial flow expansion region,leads to obviously higher SERN performance of the non-equilibrium flow than that of the frozen flow.Furthermore,the distributed fuel injection pattern plays a significant role in enhancing the combustion efficiency in combustor,but weakening the chemical non-equilibrium effects funciton in SERN.Additionally,while the equivalent mixture ratio increases,the SERN thrust coefficient and lift coefficient rise gradually,and the increment of non-equilibrium flow in relation to frozen flow becomes higher as well.To be specific,the equivalent mixture ratio is 0.6,the maximum increment of thrust coefficient and lift coefficient are 11.6% and 25% respectively.      

超燃冲压发动机前体边界层转捩风洞试验方法

吸气式高超声速飞行器前体边界层强迫转捩研究是各国高超声速研究计划的重要内容之一。本文归纳总结了美国开展Hyper-X前体边界层强迫转捩研究风洞设备的选则依据和选用的主要风洞;归纳了各风洞在超燃冲压发动机前体边界层强迫转捩试验中采用的主要测量和显示技术;分析了强迫转捩扰流装置设计过程中,风洞试验研究采用的方法。     

超燃试验用加热器三维粘性流场数值模拟

超燃冲压发动机试验时,使用燃烧型加热器模拟高焓、高马赫数的来流条件,而加热器的喷注结构对改善加热器出口流场均匀性具有重要作用.使用三维数值模拟软件Fluent对2种喷注结构的燃烧型加热器进行了三维定常反应流场模拟,获得了设计工况下的流场.结果表明,采用多孔斜喷结构能使氢气在横向有较大的穿透深度,加上空气的引射作用在燃烧室头部产生大尺度横向涡,增强了氢气和空气的混合燃烧以及燃气的掺混,使加热器出口温度场不均匀性从53%降为21%,氧气摩尔分数不均匀性从63%降为17%,更有利于开展超燃冲压发动机试验.