关于刚体转动的角速度和角加速度的讨论

在理论力学教学中，平面运动刚体的转动与基点无关的证明过于简单，本利用矢量代数的知识，证明平面运动刚体的角度与角加速度与基点的选择无关。     

高旋转数内冷通道换热实验技术及验证

通过内冷通道换热理论分析及实验系统优化,获得了使内冷通道内气体压力保持在500kPa以上的高旋转数实验技术.旋转数和雷诺数的范围分别为0~2.08,104~7×104,极大满足了旋转数与雷诺数同时覆盖真实发动机涡轮叶片工作参数的实验需求.证实了雷诺数和旋转数对内冷通道换热的影响可以解耦.而应用该实验技术进行同等旋转数实验时,内冷通道热损失占总加热量的比例和实验误差分别降低到18%和±10%.     

FY—1C卫星姿态控制系统

针对FY－1C卫星姿态控制系统，给出了系统方案、系统设计、系统特点和飞行试验的结果；对一些新的技术设计和新颖特殊的方案特点，从理论分析和技术实现给出了设计思路和工程实现的方法；分析了FY－1C卫星姿态控制系统在轨运行的结果；对长寿命、低成本和稳定连续运行的工程实现进行了研究；给出了FY－1C卫星姿态控制系统的水平能力和应用发展方向。     

基于四元数法的舰载无人机回收系统测高技术研究

文章针对舰载无人机在着舰回收过程中,由于海浪颠簸对引导系统高度测量严重干扰的问题,利用四元数导航算法提出了一种新型的舰载无人机回收系统测高方法。首先采用捷联惯导测高系统设计方案,同时利用微机械的惯性测量组件,提高系统的可靠性和集成度;然后,利用四元数导航算法求取各个姿态方位参数,再用旋转矢量法补偿不可交换性误差,推导出舰船甲板的升沉高度实际值,为克服传统纯惯导测量算法的不稳定性,提出一种具有三阶阻尼特性的互补滤波器算法,并在测量系统输入端加入巴特沃斯滤波器去除杂波干扰,得到需要测量的高度变化值。最后,通过对比传统纯惯性方法下测高系统输出值、加入真实气压表互补滤波后测高系统输出值和加入零均值阻尼信号互补滤波测高系统输出值,三种不同情况下的仿真结果,验证了所提方案的有效性。     

无刷直流电动机旋转感应电压的分析与计算

系统地推导了无刷直流电动机旋转感应电压的通用计算公式,并以这些公式为基础,详细研究了气隙磁密平顶宽度、分布绕组、短距、分数槽、斜槽等因素对旋转感应电压的影响,给出了在保证旋转感应电压是平顶宽度为理想值的梯形波时,转子磁钢和定子绕组设计时应考虑的因素.本文的研究内容为高性能低转矩波动无刷直流电动机的设计提供了理论基础.      

Contact-free release dynamics of tens of stacked satellites with multiaxial rotations

Stacked satellites have a promising application in aerospace engineering for the merits of high launch efficiency and networking capability. As one of the key technical points, releasing tens or even hundreds of satellites from the stacked state in a simple and contact-free manner is of importance. In this paper, the contact-free release dynamics of tens of stacked satellites is studied with only the initial multiaxial rotations of the system. First of all, a rigid multibody dynamic model of the stacked satellite system is established via the natural coordinate formulation (NCF). The NCF modeling scheme is able to describe the large overall motions of the satellites without any singularity and makes it possible to simplify the varying constraints between the satellites. Then, the orbital dynamics of the stacked satellite system is derived via coordinate transformation by taking the Coriolis forces, centrifugal forces, and gravity gradient into consideration. In order to rapidly and accurately detect the possible contact between satellites, a convex optimization model for minimum distance computation is proposed by using a hyperelliptic approximation for a cubic satellite. Finally, a benchmark example is given to validate the contact detection algorithm and three release dynamic cases for the stacked satellites are presented to demonstrate the effectiveness of the contact-free releasing approach with multiaxial rotations.     

The effect of neglecting VLBI reference station clock offsets on UT1 estimates

Very Long Baseline Interferometry (VLBI) allows to monitor universal time (UT1) by conducting regular international experiments. Such dedicated observation networks are equipped with different hardware components, which require different processing strategies when the data are correlated. As the timing units at each stations are usually offset with respect to universal time (UTC) this effect should be considered during correlation processing. Thus, it is investigated how neglecting of these offsets theoretically impacts the estimation of UT1. Three different strategies for the proper handling of the timing offset will be discussed and their advantages/drawbacks will be pointed out. Moreover, it is studied how neglecting of these timing offsets affects UT1 time-series and how such a missing correction can be applied a posteriori. Although the discussed effect is for most of the UT1 experiments smaller than the formal error of the estimates, it is important to consider station clock offsets properly in next-generation VLBI systems, which are expected to improve accuracy of results by about one order of magnitude.     

介质阻挡放电等离子体的温度测量

在空气介质阻挡放电中,利用氮分子振动谱线和氮分子离子的转动谱线,研究了振动温度和转动温度在两极板间的分布情况。结果表明：越靠近极板振动温度越小,中间振动温度最高;而转动温度在两极板间基本保持不变。     

微小卫星高精度三轴稳定控制算法研究

某型号微小卫星的有效载荷为三线阵CCD相机 ,因此对于姿态控制系统有相当高的要求 :对地定向三轴稳定指向精度优于 0 .3°,稳定度优于 0 .0 0 1(°) /s。针对该要求进行了控制系统设计 ,并在单轴气浮转台的基础上 ,根据国内现有硬件情况进行了半物理仿真验证。结果表明 :所设计的控制器原理简单、易于实现且具有较好的鲁棒性 ,满足总体提出的设计要求。同时证明 ,国内现有的光纤陀螺和反作用飞轮等硬件的性能指标均可满足某型号微小卫星姿态控制系统的要求。     

三线阵相机视轴夹角及线阵平行性装调测试

随着对实时立体测绘图像的需求,相机探测器由胶片向CCD发展。为了保证三线阵测绘相机的测绘精度,文章对三线阵测绘相机的视轴夹角及线阵平行性的装调检测进行了研究,针对测试指标提出了新的装调测试方案,并对方案中的关键技术进行了阐述。实际装调检测结果表明,该方案能够满足多相机间夹角测试精度优于5″,CCD线阵不平行度测试精度优于15″的要求。可以满足三线阵测绘相机空间位置的装调测试,具有实际应用价值。