某型飞机机翼整体油箱工艺研究

介绍了某型机机翼整体油箱的研制过程,针对总体气动、结构和使用维护等对整体油箱提出的性能要求,工程部门相应采用严格的环境措施、确保协调精度的预装配措施以及湿连接、密封装配措施等,解决了研制过程中诸多关键难题,保证了整体油箱的研制进度和产品质量,经各种试验检测和试飞考核,该整体油箱质量稳定可靠,性能良好。     

液体火箭发动机涡轮泵用机械密封温度场及热载变形研究

基于ANSYS数值计算软件,建立了液体火箭发动机涡轮泵用机械密封的二维稳态传热模型,依靠经验公式确定了模型的对流换热系数。计算了密封环的温度场和热载变形,分析了密封端面比压、回流流量以及不同材质对密封温度场的影响规律。结果表明:密封端面最高温度发生在靠近密封环内径处,且密封端面比压越大密封环温度梯度越大;密封环热载变形呈收敛间隙,最大变形发生在动环端面的外径处,其值约为2.2μm;密封环端面最高温度随回流流量增加而减小,当回流流量从0.1~0.6 kg/s变化时,密封环端面最高温度可降低18%(从100℃降至82℃);当回流流量增大到0.3 kg/s时,继续提高对密封环端面温升的控制不再显著;采用高导热系数的摩擦副材料能够显著降低端面温升和温度梯度,提高密封工作可靠性。     

Leakage performance of floating ring seal in cold/hot state for aero-engine

Rotating experimental investigations were carried out to study the oil sealing capability of two different floating ring seals in cold/hot state for aero-engine. High-speed Floating Ring Seal(HFRS) is a seal with the inner diameter of 83.72 mm and maximum speed of 38000 r/min, and Low-speed Floating Ring Seal(LFRS) is another seal with the inner diameter of 40.01 mm and maximum speed of 18000 r/min. In hot state, sealing air with the temperature of 371 K and oil with the temperature of 343 K was employed to model the working conditions of an aero-engine. Comparisons between floating ring seal and labyrinth seal were done to inspect the leakage performance.More attention was paid to the critical pressure ratio where the oil leakage began. Results show that the critical pressure ratio in cold state is obviously larger than that in hot state for both seals. An underlying sealing mechanism for floating ring seal is clarified by the fluid film, which closely associates with the dimensionless parameter of clearance over rotating diameter(2 c/Dr). Another fantastic phenomenon is that the leakage coefficient in hot state, not the leakage magnitude, is unexpectedly larger than that in cold state. Overall, the leakage performance of the floating ring seal is better than the labyrinth seal.     

金属密封件镀金工艺研究

介绍了金属密封件镀金工艺技术,该工艺采用亚硫酸盐镀金方案,以单脉冲电源为镀覆电源,以预镀镍层为中间镀层来制备金镀层,得到了结晶细致、厚度均匀并与基体上结合牢固的金镀层.研究了金镀层的沉积速率和结合强度,观察了镀层的表面形貌和组织结构,进行了金属密封件气密性试验和典型试验.结果表明：金属密封件金镀层的技术性能指标满足设计要求,能够应用于液体火箭发动机中,该发动机已通过地面热试车考核.     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

模具约束条件对H96黄铜双脊矩形管E弯截面变形的影响

 双脊矩形管的绕弯成形受内外侧模具的共同约束,不同模具约束下管坯的受力不同,使得其截面变形情况也不相同,而截面变形严重地影响弯管件的成形质量和使用性能。因此,基于ABAQUS有限元平台建立了双脊矩形管E弯成形三维有限元模型,并通过实验验证了模型的可靠性。采用所建模型,研究了内外侧模具约束条件对双脊矩形管E弯截面变形的影响规律,发现当只有内腹板脊槽受约束时,内腹板脊槽的内缩变形可得到较好的控制,而其他部位的变形则有增大的趋势;当只有外腹板脊槽受约束时,内腹板脊槽宽度变形基本不发生变化,而其他部位的变形则有减小的趋势;当内外腹板脊槽均受约束时,可较好地控制双脊矩形管E弯过程中的截面变形。芯头个数对整管截面高度、宽度、外腹板脊槽宽度与两脊槽底部的间距的变形影响较大,但对内腹板脊槽宽度的变形影响不显著。     

对影响无人机转动运动的两个因素的分析

陀螺力矩是在高速旋转的发动机转子和无人机的转动运动相互作用下产生的。在它的作用下,无人机在不同方向上的转动运动交连起来,共同影响无人机的飞行姿态。转动惯量是决定无人机的转动运动的另一个因素。本文着重研究了陀螺力矩在无人机几个特殊的飞行段落内对无人机转动运动的影响和燃料量以及无人机姿态角变化造成的燃料分布变化对无人机转动惯量以及转动运动的影响。     

气压变化对光纤陀螺仪零偏稳定性 的影响及抑制方法研究

光纤陀螺仪可用于测量载体相对惯性空间的角运动, 是光纤惯导系统的核 心部件。因此,要求光纤陀螺仪具有较高的精度和良好的环境适应性。光纤环是光纤陀 螺仪的角速度敏感部件,光纤环受到环境因素影响,将导致光纤陀螺仪精度下降,因此 需要对光纤环采取适当的保护措施。分析了气压变化导致光纤陀螺仪零偏稳定性变差的 机理： 环境气压的急剧变化, 会使光纤环上产生附加应力, 造成光纤的折射率分布不 均,导致光路产生非互易性相位差,使光纤陀螺仪零偏产生漂移,零偏稳定性变差;并 提出了对光纤陀螺仪进行密封的措施来抑制该效应。经试验验证,采用此密封设计后, 光纤陀螺仪在变气压环境中的零偏稳定性改善了近10 倍。     

直升机旋翼载荷中的非线性强迫振动方程迭代算法

介绍用迭代方法求解直升机桨叶气动载荷中的非线性强迫振动方程。计算时,先假定诱导下洗已确定,求出桨叶的初始载荷;再通过非线性强迫振动方程求出弯－弯－扭弹性变形。以某一直升机为例,求出了桨叶的各阶谐波载荷和弹性变形。计算结果与实验数据吻合。     

受涡轮动、静叶片影响的轴向轮缘密封非定常封严特性研究

为探究受涡轮动、静叶片单独及共同作用下的轮缘密封结构封严与入侵的精细流动机理,通过SST湍流模型,对处于无叶片、仅存在动叶、仅存在静叶、动静叶均存在的4个不同环境中的典型轴向密封结构进行非定常数值模拟.结果表明:动、静叶片通过改变轮缘密封间隙出口处高、低压区之间的面积与压差,和增加间隙内的再循环及泰勒-库特型流动强度,...