Acceleration sensors based modal identification and active vibration control of flexible smart cantilever plate

Some flexible appendages of spacecrafts, such as solar panels, are cantilever plate structures. Thus, vibration problem is unavoidable when there is slewing maneuver or external disturbance excitation. Vibration of such cantilever plate structures includes coupled bending and torsional motion. Furthermore, the low amplitude vibration near the equilibrium point is very difficult to be quickly suppressed due to nonlinear factors of the hardware in the system, which is harmful to stability and attitude control accuracy. To solve these problems, acceleration sensor-based modal identification and active vibration control methods are presented for the first two bending and the first two torsional modes vibration of the cantilever plate. Optimal placements of three acceleration sensors and PZT patches actuators are performed to decouple the bending and torsional vibration of such cantilever plate for sensing and actuating, and identifications are achieved by experiments. A nonlinear control method is presented to suppress both high and low amplitude vibrations of flexible smart cantilever plate significantly. Experimental comparison researches are conducted by using acceleration proportional feedback and the presented nonlinear control algorithms. The experimental results demonstrate that the presented acceleration sensor-based methods can suppress the vibration of cantilever plate effectively.     

Lumped element modelling of synthetic jet actuators

In this paper, a lumped element model of synthetic jet actuator is presented and used to predict the temporal variation of the jet velocity. Unlike the previous model reported in the literature, in this model the mechanical movement of the diaphragm is decoupled from the fluid phenomenon in the actuator cavity to allow the modelling of fluid mechanics aspect of the actuator to be investigated and validated separately. Furthermore, the “minor losses” occurring at the orifice exit is included and linked to the jet exit velocity profile. The results from this model are validated using the existing experimental data and CFD simulations. It is found that this model is capable of predicting the temporal variation of synthetic jets both in phase and magnitude when the actuator is operating away from the Helmholtz resonance frequency. Although the model fails to predict the correct phase information at the Helmholtz resonance frequency, it can still produce the jet peak velocity that is in good agreement with the experimental data. The lumped element model presented in this paper can be used to provide a reliable prediction of the jet peak velocity needed in the initial design of synthetic jet actuators for practical applications.     

角伺服系统模糊自适应PID控制研究

将模糊控制和PID控制相结合,提出了一种智能复合控制策略,并将其应用于某型导弹系统角伺服系统的控制。利用模糊控制在线自适应调整PID控制器的参数,从而使系统的静态和动态性能指标较为理想。在Simulink中的仿真结果表明,这种模糊PID控制器的控制效果优于单纯的PID控制,超调量小,抗干扰性能强,对变参数系统的鲁棒性强,满足在线实时自适应控制的要求。     

多控制面机翼阵风减缓主动控制与风洞试验验证

针对某大展弦比多控制面弹性机翼风洞模型,分别从频域和时域进行阵风响应分析和阵风响应减缓控制律设计.采用经典控制理论设计控制律,通过操纵位于0.6和0.8翼展处的内外侧控制面减小由正弦阵风引起的翼尖加速度(WTA).低频段的阵风减缓的数值分析与风洞试验结果均表明:多控制面的阵风减缓效果优于单控制面.当来流速度为14 m/s时,针对频率为2～5 Hz的阵风,采用多控制面得到的WTA减小10%～24%;当来流速度在8～16 m/s时,针对频率为2 Hz的正弦阵风,闭环状态下的翼尖加速度减小10%～40%;结构有限元模型与真实模型存在工程允许的误差导致理论与试验结果存在一定的误差.本文的工作对工程实际中采用阵风减缓技术具有参考价值.     

基于线性稳定性理论的转捩控制试验

 使用线化稳定性理论研究了某后掠机翼试验模型在风洞试验条件下可能的试验结果。在当前试验条件下,三维边界层中横流驻波的不同波长扰动发展趋势不同,根据理论分析和数值计算给出了最大放大率波长为4.0 mm。通过升华法试验验证了理论分析与数值计算结果。在试验中使用丝网印刷技术在后掠机翼前缘添加粗糙带,成功地引入了理论计算的最大放大率波长。根据预期影响了三维边界层的转捩。     

Design of Flight Control System for a Small Unmanned Tilt Rotor Aircraft

A tilt rotor is an aircraft of a special kind, which possesses the characteristics of a helicopter and a fixed-wing airplane. However, there are a great number of important technical problems waiting for settlements. Of them, the flight control system might be a critical one. This article presents the progresses of the research work on the design of flight control system at Nanjing University of Aeronautics and Astronautics (NUAA). The flight control law of the tilt rotor aircraft is designed with the help of an inner/outer loop control structure and an eigenstructure assignment algorithm on the basis of a proper mathematical model already verified by the wind tunnel tests. The proposed control law has been born out through the construction of the flight control system and the flight tests. Now, the flight tests are still underway on a prototype of small unmanned tilt rotor aircraft. The results have evidenced the credibility of the aircraft design and the effectiveness of the flight control system for the tilt rotor working in the helicopter mode. A full envelope flight test is planned to carry out further researches on the flight control law.     

非稳态单喷口射流控制扩压器内边界层的分离流动

对扩压器内单喷口射流产生的流向涡控制扩压器内部边界层分离流动行为进行了研究。研究的对象是一个扩张角为10°的二维扩压器,扩压器进出口面积比为1∶4.7,入口高度为15 mm。采用数值计算方法研究了当射流出口速度为非稳态时对分离流动的影响。给出了不同时刻,不同截面上的旋涡涡量分布。结果表明,采用非稳态喷射流向涡方法可以在不改变主流流量特性的情况下,有效地减小分离流动区域。     

动力涡轮驱动的逆升压式空气循环制冷系统优化设计

基于典型飞行剖面分析计算,对目前电子设备吊舱所应用的各种环境控制系统进行了简要介绍,并分别分析了其优缺点.通过比较指出:动力涡轮驱动的逆升压式空气循环制冷系统是适用于电子设备吊舱冷却的有效方案之一.此系统在保证冷却涡轮处于设计工况的条件下,让部分冲压空气通过动力涡轮,因此,不会有非设计工况下冷却涡轮效率下降的问题,可以获得较大的制冷量.本文建立了该系统及各附件的数学模型,确定了系统设计计算方法,并分别以系统质量最小和性能系数最高为优化目标函数,提出了系统优化设计方法.     

大空域变轨巡航飞行器变结构控制律研究

针对超声速大空域变轨巡航飞行器在变轨过程中出现的系统矩阵摄动问题,给出了具有较强鲁棒性的变结构控制律。通过合理选取滑模面,使得设计的变结构控制律对由于飞行空域变化造成的系统矩阵的摄动具有不变性,从而保证了控制律的鲁棒性。通过对系统相平面的分析及李亚普诺夫理论证明了闭环系统的稳定性。利用饱和函数来近似符号函数,对变结构控制律的抖振现象进行消除。最后给出了数学仿真校验,结果表明所设计的变结构控制律具有较强的鲁棒性。
     

航天器环境干扰力矩的闭环辨识与补偿

研究引入干扰力矩辨识的方法提高三轴稳定航天器在稳态运行期间的高精度指向控制问题.基于航天器的稳态输出数据和系统传递函数,对环境干扰力矩的完整模型进行闭环辨识.其中采用改进的特征系统实现相关算法和多元线性回归法辨识环境干扰力矩的模型参数,最后使用前馈控制对所辨识的环境干扰力矩实现在线补偿.分析和仿真结果表明,该方案能有效地克服不确定的环境干扰力矩对姿态稳定度的影响,提高在轨运行航天器的姿态稳定精度.