Effects of Mach numbers on Magnus induced surface pressure

Experimental and numerical methods were used to investigate the Magnus phenomena over a spinning projectile. The pressure force acting on the surface of a spinning projectile was measured for various cases by employing a relatively novel experimental technique. A set of miniature pressure sensors along with a data acquisition board, battery and storage memory were placed inside a spinning model and the surface pressure were obtained through a remotely controlled system. Circumferential pressures of the model for both rotational and static conditions were obtained at two different free stream Mach numbers of 0.4 and 0.8 and at different angles of attack. The results showed the ability of this new test method to measure the very small Magnus force via surface pressures over the projectile. The results provide a deep insight into the flow structure and illustrate changes in the cross-flow separation locations as a result of rotation. Similar results were obtained by the numerical simulations and were compared with the experimental data.     

Evaluation and improvement of coastal GNSS reflectometry sea level variations from existing GNSS stations in Taiwan

Global sea level rise due to an increasingly warmer climate has begun to induce hazards, adversely affecting the lives and properties of people residing in low-lying coastal regions and islands. Therefore, it is important to monitor and understand variations in coastal sea level covering offshore regions. Signal-to-noise ratio (SNR) data of Global Navigation Satellite System (GNSS) have been successfully used to robustly derive sea level heights (SLHs). In Taiwan, there are a number of continuously operating GNSS stations, not originally installed for sea level monitoring. They were established in harbors or near coastal regions for monitoring land motion. This study utilizes existing SNR data from three GNSS stations (Kaohsiung, Suao, and TaiCOAST) in Taiwan to compute SLHs with two methods, namely, Lomb–Scargle Periodogram (LSP)-only, and LSP aided with tidal harmonic analysis developed in this study. The results of both methods are compared with co-located or nearby tide gauge records. Due to the poor quality of SNR data, the worst accuracy of SLHs derived from traditional LSP-only method exceeds 1?m at the TaiCOAST station. With our procedure, the standard deviations (STDs) of difference between GNSS-derived SLHs and tide gauge records in Kaohsiung and Suao stations decreased to 10?cm and the results show excellent agreement with tide gauge derived relative sea level records, with STD of differences of 7?cm and correlation coefficient of 0.96. In addition, the absolute GNSS-R sea level trend in Kaohsiung during 2006–2011 agrees well with that derived from satellite altimetry. We conclude that the coastal GNSS stations in Taiwan have the potential of monitoring absolute coastal sea level change accurately when our proposed methodology is used.     

Fast spacecraft solar radiation pressure modeling by ray tracing on graphics processing unit

A novel method is presented to evaluate on the graphics processing unit (GPU) the force and torque on a spacecraft due to solar radiation pressure. The method employs efficient ray tracing techniques, developed in the graphics rendering discipline, to resolve spacecraft self-shadowing and reflections at faster than real-time computation speed. The primary algorithmic components of the ray tracing process which contribute to the method’s computational efficiency are described. These components include two-level bounding volume hierarchy acceleration data structures, fast ray to bounding box intersection testing using the slab intersection algorithm and fast triangle intersection testing using the Möller-Trumbore algorithm. Spacecraft material optical properties are represented as a combination of Lambertian diffuse and ideal specular reflections. Both diffuse and specular ray-surface interactions are modeled. The approach is implemented using C++ and OpenCL and executed on a consumer grade GPU. Model validation is presented comparing ray traced force and torque values to the same quantities produce by a faceted analytic model. Numerical results illustrate the impact of self-shadowing on the force and torque calculation, and demonstrate the fast computational speed that is enabled with this implementation.     

Early analysis of precise orbit and clock offset determination for the satellites of the global BeiDou-3 system

Eight new-generation BeiDou satellites (BeiDou-3) have been launched into Medium Earth Orbit (MEO), allowing for global coverage since March 2018, and they are equipped with new hydrogen atomic clocks and updated rubidium clocks. Firstly, we analyzed the signals for the carrier-to-noise-density ratio (C/N0) and pseudorange multipath (MP) by using international GNSS (Global Navigation Satellite System) Monitoring and Assessment System (iGMAS) station data, and found that B1C has a lower C/N0, and B2a has the same level of C/N0 as the B1I and B3I signals. For pseudorange multipath, compared with the BeiDou-2 satellites, the obvious systematic variation of MP scatters related to the elevation angle is greatly improved for the BeiDou-3 and BeiDou-3e satellites signals. For the signals of the BeiDou-3 satellites, the order of the Root Mean Square (RMS) values of multipath and noise is B3I?<?B1I?<?B2a?<?B1C. Then, the comparison of the precise orbit determination and clock offset determination for the BeiDou-2, BeiDou-3, and BeiDou-3 experimental (BeiDou-3e) satellites was done by using 10 stations from iGMAS. The 3D precision of the 24?h orbit overlap is 24.55, 25.61, and 23.35?cm for the BeiDou-3, BeiDou-3e, and BeiDou-2 satellites, respectively. BeiDou-3 satellite has a comparable precision to that of the BeiDou-2 satellite. For the precision of clock offset estimation, the Standard Deviation (STD) of the BeiDou-3 MEO satellite is 0.350?ns, which is an improvement of 0.042?ns over that of the BeiDou-2 MEO satellite. The stabilities of the BeiDou-3 and BeiDou-3e onboard clocks are better than those of BeiDou-2 by factors of 2.84 and 1.61 at an averaging time of 1000 and 10,000?s, respectively.     

Potential of IRNSS/NavIC L5 signals for ionospheric studies

Indian Space Research Organization (ISRO) has developed an indigenous system named Indian Regional Navigation Satellite System (IRNSS) or NavIC (Navigation with Indian Constellation), that consists of 7 satellites and transmits navigation signal in L and S bands. ISRO, for validation of the system, has installed many IGS (IRNSS/GPS/SBAS) receivers scattered over the Indian region. Using preliminary data from two geographically widely separated stations over India, this paper presents the results on studies on parameters of IRNSS signal quality and discusses how these parameters may be used to study the ionospheric behavior over the Indian region. The results show the importance and advantages of using IRNSS data for such studies.     

Numerical investigation on flow nonuniformity-induced hysteresis in scramjet isolator

Numerical simulation and theoretical analysis were conducted to study the hysteresis inside scramjet isolator during the reciprocating process of back pressure variation. It is revealed that only a regular reflection is theoretically possible for two leading shocks when the inflow Mach number is greater than 2.0, and no hysteresis can occur in the transition between shock reflection types. Nevertheless, wall suction, gas injection, and background waves cause non-uniformity of the incoming flow and would make hysteresis possible. Besides the classical hysteresis in the transition between shock reflection, new kinds of hysteresis were found in both the deflection angle of separated boundary layer and the location of the shock train. Moreover, the occurrence of hysteresis in the deflection angle of the separated boundary layer is accompanied with the shock reflection hysteresis. In the case with background waves or gas injection, hysteresis in the starting position of leading shock was observed too. As back pressure decreases, the leading shock does not follow the same path as that as the back pressure increases, and it is anchored at the location where the background shock or the injection interacts with the leading shock. It is inferred that, if two strong adverse pressure gradient regions move towards and interact with each other, hysteresis will take place when they start to separate.     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

基于ALE法的水陆两栖飞机船体着水性能分析

水陆两栖飞机的着水性能是体现其综合性能的重要因素之一.应用ALE法对三种水陆两栖飞机船体截面进行入水仿真计算,从着水载荷、喷溅性能及运动响应三个方面对着水性能进行综合评估.对比分析了直线型、带舭弯弧形、复合型三种构型截面在不同速度、不同重量下的压力分布、喷溅性能以及运动响应,得到了三种截面横向压力分布规律.计算结果显示相同状态下,喷溅性能复合型优于带舭弯弧形、带舭弯弧形优于直线型;过载复合型远大于带舭弯弧形,带舭弯弧形稍大于直线型,综合看来带舭弯弧形截面着水性能最佳.     

典型工况下低排放燃烧室的压力振荡特性

为了研究低排放燃烧室在典型工况下的压力振荡特性,针对模型燃烧室进行了燃烧自激振荡特性试验.在试验中测量了采用贫油预混预蒸发(LPP)燃烧技术的低排放燃烧室在典型工况下的压力振荡频率和幅值,在燃烧室进口压力为1.10～2.77MPa、燃烧室进口温度为656～845 K、燃烧室压降为3.41％～4.35％范围内,分析了燃油粒径变化对振荡特性的影响.分析结果表明:局部当量比脉动是引发燃烧不稳定的因素之一.通过计算燃油二次雾化状态下的液滴最大粒径,发现燃油液滴粒径的变化对主燃级出口处的局部当量比脉动有直接影响,从而引起燃烧室压力振荡幅值和频率的变化.     

叶片反扭对跨声速大涵道比风扇性能的影响

使用基于流固耦合算法的叶片反扭程序,考虑了非定常气动力对叶片变形的非线性作用,研究了叶片反扭对跨声速大涵道比风扇性能的影响.以冷态叶型为起点,先计算离心力作用下的叶片变形,在此基础上使用流固耦合程序获得非定常气动力作用下的变形.考察了3个转速下叶片的动态变形对大涵道比风扇气动性能的影响.结果表明:在跨声速工况下,叶片表面激波位置的变化对叶片反扭角有很大作用,在考察的转速范围内,堵塞点使用设计叶型计算的流量大于动态叶型下的流量,数值达7%,将导致发动机起飞推力小于预测值.结果表明在大涵道比风扇设计阶段,预测气动性能使用准确叶型的重要性.