负游隙对高速高温薄壁圆柱滚子轴承动态性能的影响分析

计算了圆柱滚子轴承径向游隙为负值时的等效径向预紧载荷,并考虑等效径向预紧载荷下的套圈弹性变形,通过求解包含套圈弹性变形接触变形等效径向预紧载荷的非线性方程组,得到负游隙圆柱滚子轴承内部的载荷分布情况,以及负径向游隙带来的套圈周向应力.以此分析了负游隙对轴承承载性能及疲劳寿命的影响.结果表明:负径向游隙能够有效降低轴承打滑率,但同时也会降低轴承疲劳寿命,因此在负游隙设计时需同时考虑打滑率和轴承寿命,选择恰当的负游隙.     

平箔片楔形高度对气体止推箔片轴承特性影响

针对波箔型气体止推箔片轴承,建立了箔片结构二维薄板模型,并通过有限差分法和有限元法耦合求解可压缩气体Reynolds方程和气膜厚度方程,获得了给定轴承载荷条件下轴承气膜压力分布、气膜厚度分布、平箔片变形量和功率损耗等轴承特性.通过对比楔形高度分别为25,70,100,200,300μm时的轴承特性仿真结果研究了楔形高度对轴承性能的影响.结果表明:降低楔形高度使轴承气膜压力分布更均匀,并降低了平箔片的局部集中载荷.但楔形高度存在一个最佳值,使得达到相同轴承载荷所需的最小气膜厚度最大,并且轴承具有最小功率损耗,提高了轴承的工作效率.该结果为气体止推箔片轴承的结构设计提供的理论参考.      

Advances and trends in plastic forming technologies for welded tubes

With the implementation of environmental protection, sustainable development and conservation-oriented policies, components and parts of thin-walled welded tubes have gained increasing application in the aircraft and automotive industries because of their advantages: easily achieving forming and manufacturing process at low cost and in a short time. The current research on welded tube plastic forming is mainly concentrated on tube internal high-pressure forming, tube bending forming, and tube spinning forming. The focuses are on the material properties and characterization of welded tubes, finite element modeling for welded tube forming, and inhomogeneous deformation behavior and the mechanism and rules of deformation coordination in welded tube plastic forming. This paper summarizes the research progress in welded tube plastic forming from these aspects. Finally, with a focus on the urgent demand of the aviation, aerospace and automotive industries for high-strength and light-weight tubes, this paper discusses the development trends and challenges in the theory and technology of welded tube plastic forming in the future. Among them,laser tailor-welded technology will find application in the manufacture of high-strength steel tubes.Tube-end forming technology, such as tube flaring and flanging technology, will expand its application in welded tubes. Therefore, future studies will focus on the FE modeling regarding how to consider effects of welding on residual stresses, welding distortions and microstructure, the inhomogeneous deformation and coordination mechanism of the plastic forming process of tailor-welded tubes, and some end-forming processes of welded tubes, and more comprehensive research on the forming mechanism and limit of welded tubes.     

基于纯比例导引的拦截碰撞角约束制导策略

拦截碰撞角约束制导是当前导弹制导研究的关键问题之一。首先基于理想比例导引（IPN）律拦截非机动目标的解析解,推导了纯比例导引律（PPN）拦截固定目标的解析解,得到了弹目相对距离、制导指令加速度和导弹前置角的显示表达式,并进一步得到了拦截碰撞角与弹目相对运动状态和比例导引系数之间的解析表达式。其次,基于该解析表达式,提出了基于PPN的拦截碰撞角约束制导策略（PPNIACG）,并探讨了在铅垂面内进行落角约束打击和水平面内进行拦截碰撞角约束打击的2种实现方式。最后,以弹道成型制导律（TSG）和最优碰撞角约束制导律（OIACG）为参考,通过数值仿真算例,对PPNIAC的拦截性能进行了对比分析,验证了所提出制导策略的有效性和正确性。     

Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected.     

整体弹性结构法及在叶片流固耦合分析中的应用

针对三维叶片时域流固耦合振动响应计算普遍耗时的问题,采用一种假设整体结构的模态位移,求解固体时域响应和实现高效网格变形,发展了一种3维时域流固耦合分析的整体弹性结构方法,并应用于压气机叶片0°和180°相位角的气动稳定性分析中。结果表明,所发展方法的计算结果与传统双向时域算法和文献的结果较为吻合,而计算效率相比于传统算法显著提升;在所分析的两个相位角下,叶片振动的气动阻尼均随流量减小先增大后降低,相比于0°相位角,180°下叶片的气动稳定性大幅提高,表明该方法能有效应用于叶片的工程流固耦合研究。     

Hypervelocity impact induced shock acoustic emission waves for quantitative damage evaluation using in situ miniaturized piezoelectric sensor network

Manmade debris and natural meteoroids, travelling in the Low Earth Orbit at a speed of several kilometers per second, pose a severe safety concern to the spacecraft in service through the HyperVelocity Impact(HVI). To address this issue, an investigation of shock Acoustic Emission(AE) waves induced by HVI to a downscaled two-layer Whipple shielding structure is performed,to realize a quantitative damage evaluation. Firstly a hybrid numerical model integrating smoothparticle hydrodynamics and finite element is built to obtain the wave response. The projectiles, with various impact velocities and directions, are modelled to impact the shielding structure with different thicknesses. Then experimental validation is carried out with built-in miniaturized piezoelectric sensors to in situ sense the HVI-induced AE waves. A quantitative agreement is obtained between numerical and experimental results, demonstrating the correctness of the hybrid model and facilitating the explanation of obtained AE signals in experiment. Based on the understanding of HVI-induced wave components, assessment of the damage severity, i.e., whether the outer shielding layer is perforated or not, is performed using the energy ratio between the regions of ‘‘high frequency" and ‘‘low frequency" in the acquired AE signals. Lastly, the direct-arrival fundamentalsymmetric wave mode is isolated from each sensing signal to be input into an enhanced delay-andsum algorithm, which visualizes HVI spots accurately and instantaneously with different sensor network configuration. All these works demonstrate the potential of quantitative, in situ, and real time HVI monitoring using miniaturized piezoelectric sensor network.     

柔性扑翼非定常流场的数值计算方法

提出一种将Delaunay图映射网格变形技术和非结构嵌套网格方法结合使用的策略,解决网格变形和嵌套网格单独用于柔性扑翼流场计算时需要网格再生的问题。该方法为嵌套网格中的每个嵌于背景网格的贴体非结构网格生成Delaunay背景图;每个时间步,根据扑翼的运动和变形规律移动背景图,再根据网格点和背景图的映射关系移动网格点,之后自动完成嵌套边界的定义和插值关系的建立。为方便嵌套关系的建立,嵌套网格进行分层管理。也研究了一种内存消耗少、效率较高的搜索算法,以及格心格式和格点格式统一的边界拓宽算法。非定常可压缩Navier-Stokes方程在非结构的动态网格上用有限体积法离散,并用预处理的双时间步推进、隐式LU-SGS迭代求解。几个扑翼算例的结果表明,该方法充分利用了Delaunay图映射网格变形方法的高效率,同时也发挥了嵌套网格处理大幅运动的优势;用于既有整体大幅扑动又有局部小变形的柔性扑翼流场计算,可取得令人满意的精度和效率。     

直升机旋翼桨叶的弹性碰撞动力学建模

建立了直升机旋翼桨叶弹性正碰撞的动力学模型,采用有限转动梁理论处理桨叶的弹性变形,利用Hertz接触理论处理局部弹性变形,引入位移协调方程识别弹性碰撞载荷,运用Hamilton原理建立了桨叶正碰撞的动力学方程.通过与Timoshenko算例的对比表明了该方法的正确性,且对集中质量与直升机桨叶的弹性正碰撞问题进行了研究.      

考虑弯扭变形的叶片模型配准方法

叶片测量数据与其CAD模型的配准定位是叶片几何形状分析的关键步骤。针对涡轮叶片的弯扭变形对叶片模型配准定位的不利影响,提出一种考虑弯扭变形的叶片模型配准方法,以提高叶片模型配准的可靠性与鲁棒性。在迭代最近点算法的目标函数中引入预变换函数,建立考虑弯扭变形的叶片模型配准目标函数。对叶片模型做切片化处理,进行弯扭变形分析生成叶片弯扭变形曲线,使用叶片弯扭变形曲线指导叶片测量数据配准。使用仿真生成带弯扭变形的叶片数据与通过坐标测量机获取的叶片实测数据对配准方法进行了验证。结果表明,所讨论方法能提高模型配准的可靠性,避免弯扭变形可能导致的叶片模型配准失败。