导弹燃气流瞬态温度测量系统设计

介绍了采用蓝宝石黑体腔光纤作为传感器的导弹燃气流瞬态温度测量系统的测量原理、系统组成,阐述了其硬件功能模块设计,给出了软件设计算法及蓝宝石黑体腔光纤高温计的标定方法。     

Mechanical behavior and properties of fiber reinforced ceramic matrix composites for high temperature use

Ceramics can keep their mechanical characteristics up to 2 000℃ or higher.In this paper,A model to predict ultimate strength of continuous fiber-reinforced brittle matrix composites is developed.A statistical theory for the strength of a uni-axially fiber-reinforced brittle matrix composite is presented.Also a semi-empirical frictional heating method for estimating in-situ interfacial shear in fiber-reinforced ceramic matrix composites was improved.Local uneven fiber packing variation as well as uneven micro-damage during fatigue can be expected to have effects on the composites:generation of frictional heating,thermal gradients,and residual stresses around local fiber breaks.This study examined those engineering interests by the finite element method.      

基于椭圆路径的光学镜面超精密研磨技术研究

利用基于椭圆成形方法建立的二次回转曲面加工误差模型,并用最小二乘方法建立了二次回转曲面铣磨误差辨识模型。考虑到各项误差对面形误差影响的相似性,分析了合并、分开辨识相似误差所引入的误差,以此得到处理相似误差的策略。     

大扫描视场飞行器共形光学系统设计

共形光学窗口外表面与飞行器轮廓相同,可以显著提升飞行器的整体性能,但在大扫描视场应用时,引入大量非对称动态像差,严重影响成像质量。针对大扫描视场的共形光学系统,提出了基于共形窗口内表面优化,以及分视场单元透镜阵列的动态像差校正方法,实现动态像差的静态化校正。在84°扫描视场范围内,对共形光学系统进行仿真验证,结果表明：该方法使共形光学系统在全扫描视场范围内的Zernike多项式系数绝对值从0~10.82λ减小到0~1λ（λ为波长）,同时各通道单元透镜阵列保持固定状态。与目前已有方法相比,本文显著提升了大扫描视场共形光学系统的成像质量和系统稳定性,有效简化了系统结构。本文的研究对实现大扫描视场、高成像质量和高稳定性的共形光学系统有重要意义。     

利用偏振图像加权融合及CLAHE算法的水下成像方法

针对传统基于偏振差分原理的水下光学成像方法中目标退偏振特性差异引起的图像中局部反射光损失的问题,本文提出了基于偏振图像加权融合与限制对比度自适应直方图均衡（Contrast Limited Adaptive Histogram Equalization, CLAHE）算法的水下成像方法。一方面,将原始水下图像分解为偏振光强图像和非偏振光强图像,根据不同退偏振特性目标在两幅图像中的灰度值分布特点,设计相应的权重因子,对两幅图像进行加权融合。从而实现在压缩原始水下图像中散射光的同时,保留更多目标反射光,提升整体目标反射光在融合图像中所占的比例。另一方面,为了进一步提升融合图像的对比度,利用限制对比度自适应直方图均衡算法对融合图像进行处理。该算法能够在提升融合图像对比度的同时,有效避免图像噪声的放大。实验结果表明,相比于传统的偏振差分方法以及独立的直方图均衡化算法,本文提出的算法能够有效提升水下图像的清晰度和对比度。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

Microstructure and Martensitic Transformation Behaviors of Explosively Welded NiTi/NiTi Laminates

The study is a first attempt to prepare bulk NiTi/NiTi shape memory alloy (SMA) laminates with a macroscopic heterogeneous composition by explosive welding and investigate their microstructures and martensitic transformation behaviors. After explosive weld- ing, a perfect interfacial bonding between the two components and a reversible martensitic transformation are realized in the tandem. Results show achievement of a fine granular structure and the maximum value of microhardness near the welding interface because of the excessive cold plastic deformation and the high impact velocity during the explosive welding. Meanwhile, the effects of aging on the transformation of the welded tandem are investigated by differential scanning calorimeter (DSC) and subject to discussion. The trans- formation temperatures of NiTi/NiTi SMAs increase with the rise of the aging temperature. The experimental results indicate the shape memory properties of NiTi/NiTi SMA fabricated by explosive welding can be improved by optimizing the aging technology.     

关于纤维增强复合材料力学性能可设计性的分析

纤维增强复合材料是一种多相结构材料,主要由增强纤维和树脂基体材料组成。其性能可设计性是指可按照设计要求进行选择不同的增强材料和树脂基体材料以及它们的含量和各种铺层形式,可组成具有不同性能的各种复合材料。这给复合材料可设计性提供更大的自由度。该文结合工程应用需要,主要对其力学性能可设计性进行了分析研究。     

航天光学遥感器光学装调技术现状与展望

航天光学遥感器工作于太空中,长期恶劣的空间环境及短暂发射入轨时的状态对光学系统的设计与装调提出了苛刻的要求,确保光学系统在轨像质优异是航天光学遥感器研制的关键技术.文章结合国际上航天光学遥感器的发展需求对光学系统装调技术及发展现状进行了分析、总结,提出了中国后续航天光学遥感器装调与测试技术的突破方向.     

A review of friction stir joining of SiCp/Al composites

SiCp/Al composites have excellent comprehensive properties and have been widely used in aerospace, automotive industry and other fields. Due to the huge difference in performance between SiC particles and matrix alloys, traditional fusion welding methods are difficult to meet the join requirements of SiCp/Al composites. Friction stir joining (friction stir welding), as a solid phase joining process, has been proved to be a new technology with fine prospect in joining SiCp/Al composites compared with fusion welding process. Although some progress has been made in recent years, there are still full of challenges. In this paper, the research status of friction stir joining of SiCp/Al composites in recent years is expatiated, including the weldability of SiCp/Al composites, the macrostructure and the microstructure of joints, mechanical properties of joints, and tool wear and monitoring. Furthermore, the existing challenges of friction stir joining of SiCp/Al composites are summarized and the future development directions are prospected.