固液混合火箭发动机固体燃料的燃速计算

分析了固液混合火箭发动机的燃烧特点、燃烧中气相过程和固体燃料内部的传热过程,利用由传热理论得出的固体燃料燃速公式和阿累尼乌斯(Arrhenius)燃速公式耦合计算,得到了燃速与氧化剂流率、轴向距离、装药初温和时间的变化规律.计算结果表明固体燃料燃速主要受氧化剂流率和轴向距离的影响,随氧化剂流率的增加而增加,随轴向距离的增加而减小.固体燃料燃速温度敏感性小,在设计发动机时可以不考虑装药初温的影响.利用热力计算得到了绝热燃烧温度与氧化剂流率和药柱长度的变化规律,绝热燃烧温度随氧化剂流率的增加存在一最大值.计算结果与相关文献的报道比较吻合,为进一步研究固液混合火箭发动机的燃烧及流动问题打好了基础.     

航材消耗的时间序列分析

本文采用时间序列分析法对某种航材故障率进行预测,用移动平均法消除时间序列的长期趋势和周期变动,然后按月平均法求出季节指数,并对季节指数进行调整,然后根据拟合的趋势方程对此种航材的故障率进行预测.其结果能为航材的可靠性保障提供理论依据.     

SCC investigation of low alloy ultra-high strength steel 30CrMnSiNi2A in 3.5wt%NaCl solution by slow strain rate technique

To evaluate stress corrosion cracking(SCC) mechanism of low alloy ultra-high strength steel 30CrMnSiNi2 A in environment containing NaCl, SCC behavior of the steel in 3.5wt% NaCl solution is investigated by slow strain rate technique(SSRT) with various strain rates and applied potentials, surface analysis technique, and electrochemical measurements. SCC susceptibility of the steel increases rapidly with strain rate decreasing from 1 · 10 5s 1to 5 · 10 7s 1, and becomes stable when strain rate is lower than 5 · 10 7s 1. SCC propagation of the steel in the solution at open circuit potential(OCP) needs sufficient hydrogen which is supplied at a certain strain rate.Fracture surface at OCP has similar characteristics with that at cathodic polarization 1000 mVSCE, which presents characteristic fractography of hydrogen induced cracking(HIC).All of these indicate that SCC behavior of the steel in the solution at OCP is mainly controlled by HIC rather than anodic dissolution(AD).     

军机无维修待命时间试飞验证方法研究

以工程应用为出发点,提出了试验机技术状态确定的依据、单次无维修待命时间验证成败判据、特殊气象条件下试验数据处理方法、无维修待命时间验证评估模型.在此基础上,以某型歼击机为例给出了试飞阶段无维修待命时间验证方案设计方法.该方法工程应用性强,可作为试飞阶段外场开展无维修待命时间验证的依据.     

Characteristics of the soil-like substrates produced with a novel technique combining aerobic fermentation and earthworm treatment

The soil-like substrate (SLS) technique is key for improving the closure of bioregenerative life support system (BLSS) by recycling the inedible biomass of higher plants. In this study, a novel SLS technique (NSLST) was proposed: aerobic fermentations at 35 °C for 1 day, then 60 °C for 6 days, finally 30 °C for 3 days, followed by earthworm treatment for 70 days. Comparing with the original SLS technique (OSLST), its process cycle was 13 days shorter, and the dry weight loss rate (81.1%) was improved by 24.77%. The cellulose and lignin degradation rates were 96.6% and 94.6%. The concentrations of available N, P and K in mature SLS were respectively 776.1 mg/L, 348.0 mg/L and 7943.0 mg/L. Low CH₄ and NH₃ production was observed, but no accumulation. According to the seed germination test, the SLSs were feasible for plant growth. This investigation will provide a preliminary foundation for BLSS design.     

某型直升机液压减摆器渗油故障的排除

介绍了某型直升机液压减摆器的结构特点和密封原理,用故障树的方法梳理了影响液压减摆器渗油的原因,针对一特定案例进行了渗油原因分析,并制定了相应的改进措施。     

Drilling load modeling and validation based on the filling rate of auger flute in planetary sampling

Some type of penetration into a subsurface is required in planetary sampling. Drilling and coring, due to its efficient penetrating and cuttings removal characteristics, has been widely applied in previous sampling missions. Given the complicated mechanical properties of a planetary regolith, suitable drilling parameters should be matched with different drilling formations properly. Otherwise, drilling faults caused by overloads could easily happen. Hence, it is necessary to estab-lish a drilling load model, which is able to reveal the relationships among drilling loads, an auger's structural parameters, soil's mechanical properties, and relevant drilling parameters. A concept for the filling rate of auger flute (FRAF) is proposed to describe drilling conditions. If the FRAF index under one group of drilling parameters is less than 1, this means that the auger flute currently removes cuttings smoothly. Otherwise, the auger will be choked with compressed cuttings. In dril-ling operations, the drilling loads on the auger mainly come from the conveyance action, while the drilling loads on the drill bit primarily come from the cutting action. Experiments in one typical lunar regolith simulant indicate that the estimated drilling loads based on the FRAF coincide with the test results quite well. Based on this drilling load model, drilling parameters have been opti-mized.     

置氢TC4钛合金粉末烧结材料高温流变行为及组织演变

采用热压缩试验研究了置氢量0.42%(质量分数)TC4钛合金粉末烧结材料在温度850～1000℃和应变速率0.001～0.10 s-1范围内的流变行为和组织演变,分析了该合金烧结材料在试验参数范围内变形的应力-应变曲线特征.动力学分析获得置氢TC4钛合金粉末烧结材料高温压缩变形的应力指数和变形激活能分别为3.97和50...     

原始疲劳质量评定和裂纹扩展方法研究

在对带有一个铆接孔的试件进行试验研究的基础上,利用性能退化失效曲线,提出了一种新的初始疲劳质量和裂纹扩展速率的确定方法。根据试验结果和理论推导,建立了裂纹扩展长度与加载循环次数的函数关系。在此基础上,估算了EIFS值,并用指数函数拟合方法估计了疲劳裂纹扩展速率。最后通过对临界裂纹尺寸的理论计算验证了新方法的可行性和有效性。     

利用端区射流调节涡轮流量的数值研究

采用三维数值模拟方法对在导叶端区射入第二股气流的涡轮流场进行计算,分析了各喷气参数(如喷气位置、角度、流量、马赫数以及总温总压等)对涡轮流量的影响规律.结果表明:涡轮流量对喷气位置相当敏感,精确的喉道位置有利于流量调节;与主流成钝角喷气对涡轮流量的调节效果较好,且喷气流量与涡轮流量的变化呈线性关系;喷气马赫数在亚声速范...