航天材料热物理性能测试技术的发展现状

根据航天材料热物理性能测试技术的特点 ,系统介绍了国内航天材料热物理性能测试技术的发展状况和发展趋势 ,并详细介绍了目前我国航天材料热物理性能测试领域中所具备的测试技术和测试装置、航天热物理性能所涉及的研究领域和内容以及目前正在开展的研究工作。     

喷管扩张段烧蚀的“台阶效应”计算

当喉衬和扩张段内衬采用具有不同烧蚀率的材料时,常出现“台阶效应”.本文以气动热化学烧蚀机理为基楚,提出应用适当的对流换热和加剧的化学反应计算对台阶效应区进行修正的方法,使台阶效应区的烧蚀率预示更切合实际工况.     

Microstructure,porosity and mechanical properties of selective laser melted AlSi10Mg

Finite element modeling (FEM), microscopy, X-ray computed tomography (CT) and mechanical property tests were used to study the microstructure, porosity and mechanical properties of an AlSi10Mg alloy produced by selective laser melting (SLM). The simulation of the melt pool and thermal history under different energy densities produced an optimized result with an energy density of 44.5 J·mm⁻³. The high cooling rate during the SLM process significantly refined the previous α-Al dendrites. The growth direction of the network-like Al-Si eutectic structure at different orientations confirmed the anisotropic nature of the microstructure. Furthermore, the microhardness, tensile testing and fracture analysis results proved that there were no obvious distinctions in the strength between the transverse and longitudinal directions, and that the ductility was anisotropic, possibly due to the shape and distribution of the pores. The pores measured by X-ray CT at different energy densities confirmed that the sphericity of the pores was inversely related to pores volumes. With optimized processing conditions, the porosity of the selective laser melted sample decreased leading to the improved fabricated fuel system component via SLM.     

永磁约束电子束轨迹实验研究

通过设计并运用一种直流电子束轨迹简易测量方法,开展了永磁约束电子束轨迹实验研究,得到了永磁铁环对60~80 ke V电子束约束作用的实验数据。结果表明:该测量方法方便有效,结果较为准确;永磁铁对电子束聚焦作用明显,并呈现出一定的规律性。对永磁铁约束电子束研究工作奠定了基础。     

丁腈橡胶增韧环氧树脂基烧蚀防热材料性能

以丁腈橡胶(CTBN)为增韧剂对环氧树脂(F51)进行增韧改性,通过FTIR、TG以及力学性能测试研究了丁腈橡胶对环氧树脂固化反应、热稳定性能和力学性能的影响,并分析了其增韧机理;分别采用燃气流剪切烧蚀试验和电弧风动烧蚀实验考核了低密度烧蚀材料的烧蚀性能。结果表明:经CTBN改性后,两者的分子链产生了一定程度的交联;树脂基体的拉伸、弯曲性能有所下降,但韧性得到了增强;热稳定性大大提高,增韧后的F51树脂在800℃时的残重率由增韧前的23%提高到了54%;低密度烧蚀材料的抗剪切、抗剥蚀能力得到了增强,且碳层的尺寸稳定性也得到了改善,烧蚀性能提高。     

热处理对FeCo-2V-0.5Cr软磁合金力学与磁学性能的影响

针对FeCo-2V-0.5Cr软磁合金,研究了真空热处理时间对其微观组织结构、力学与磁学性能的影响规律,发现在800℃下热处理时间为2h左右时,合金的抗拉强度和延伸率达到最佳,同时仍保持良好的软磁性能,抗拉强度、延伸率以及矫顽力分别为867.8MPa、10.4%以及2.0Oe。进一步对该合金进行附加磁场下的真空热处理,重点研究了合金的交流损耗与矫顽力随附加磁场方式包括磁场撤除温度与磁场下保温时间的变化规律,发现适当的磁场热处理对合金相关力学性能影响不大,但由于合金中产生了单轴各向异性而使合金矫顽力进一步降至1.6Oe。     

PBT弹性体力学性能及低温脆性研究

采用一步法制备了热固性3,3-双(叠氮甲基)环氧丁烷-四氢呋喃共聚醚(PBT)弹性体,并对其氢键结构、应力-应变关系和动态力学性能及低温脆性进行了研究。结果表明,合成的PBT弹性体拉伸强度和断裂伸长率在DEG羟基含量为35%、R=0.97时,可达2.51 MPa和1 274%,玻璃化温度为-34.5℃。高DEG含量的PBT弹性体脆化参数较低,与常温力学性能变化规律相反。因此,引入低温脆化参数,对PBT弹性体的性能优化具有积极意义。     

改性双马来酰亚胺树脂预浸料性能研究

采用二烯丙基双酚A(Ortho-dially Bisphenol A,以下简称O-DABPA)对T型双马来酰亚胺(Bismaleimide,以下简称BMI)树脂进行改性,并用红外光谱(Fourier TransformInfrared,以下简称FT-IR)、差式扫描量热仪(Differential ScanningCalorimetry,以下简称DSC)对改性前后的树脂结构及固化反应进行测定,利用热熔预浸法对改性BMI树脂制备预浸料,考查了预浸料的力学性能及高温下的弯曲性能。结果表明,在175℃下二烯丙基双酚A和T型双马来酰亚胺树脂质量比为1∶1,反应时间为1 h时,改性BMI树脂制备的预浸料工艺性良好,单向板层间剪切强度为84.86 Mpa,在240℃时,弯曲强度及模量分别为1 326.41 MPa和120.31 GPa,强度保留率为76.73%。     

The effects of the solar magnetic polarity and the solar wind velocity on Bz-component of the interplanetary magnetic field

We have studied the effect of both solar magnetic polarity and the solar wind velocity on the Bz-component of the interplanetary magnetic field, IMFBz, for the minimum activity of the solar cycles 21, 22, 23 and 24. We made a statistical study of IMFBz in the first section which is considered as an extension of Lyatsky et al. (2003). They made a statistical study of IMFBz for two periods of minimum solar activity 22 and 23 related to 1985–1987 and 1995–1997 when the solar magnetic field had opposite polarity. Our results seem to be consistent with the results obtained by Lyatsky et al. (2003). We found that there is a dependence of IMFBz on the IMFBx and the solar magnetic polarity for the minimum periods of the selected four solar cycles. In addition, we found that there is a dependence of IMFBz on the solar wind velocity.     

基于循环平稳性的噪声调频干扰高分辨测向方法

根据噪声调频信号循环平稳特性分析,提出了基于阵列接收信号循环均值-空域处理的波达方向(DOA)估计算法。仿真结果表明:该算法的角度估计性能明显高于比幅比相单脉冲测角法,且在高信噪比环境中,该法的估计性能更好、运算量较小。