L׳ADROIT – A spaceborne ultraviolet laser system for space debris clearing

Small (1–10 cm) debris in low Earth orbit (LEO) are extremely dangerous, because they spread the breakup cascade. Pulsed laser active debris removal using laser ablation jets on target is the most cost-effective way to re-enter the small debris. No other solutions address the whole problem of large (~100 cm, 1 t) as well as small debris. Physical removal of small debris (by nets, tethers and so on) is uneconomical because of the energy cost of matching orbits. In this paper, we present a completely new proposal relative to our earlier work. This new approach uses rapid, head-on interaction in 10–40 s rather than 4 minutes, using 20–40 kW bursts of 100 ps, 355 nm UV pulses from a 1.5 m diameter aperture on a space-based station in LEO. The station employs “heat-capacity” laser mode with low duty cycle to create an adaptable, robust, dual-mode system which can lower or raise large derelict objects into less dangerous orbits, as well as clear out the small debris in a 400-km thick LEO band. Time-average laser optical power is less than 15 kW. The combination of short pulses and UV wavelength gives lower required fluence on target as well as higher momentum coupling coefficient. An orbiting system can have short range because of high interaction rate deriving from its velocity through the debris field. This leads to much smaller mirrors and lower average power than the ground-based systems we have considered previously. Our system also permits strong defense of specific assets. Analysis gives an estimated cost less than $1 k each to re-enter most small debris in a few months, and about 280 k$ each to raise or lower 1-ton objects by 40 km. We believe it can do this for 2000 such large objects in about four years. Laser ablation is one of the few interactions in nature that propel a distant object without any significant reaction on the source.     

基于全球网和区域网SLR数据的低轨卫星定轨精度分析

卫星激光测距(SLR)是目前低轨卫星常用的定轨手段之一.文章以贾森-1(Jason-1)和"环境卫星"(EN VISAT)实测数据为例,讨论了不同弧段长度(1天、3天和7天)的全球网SLR数据对低轨卫星定轨精度的影响,分析了基于美国网、欧洲网和亚洲网等区域网SLR数据的低轨卫星精密定轨精度.检验定轨精度的参考轨道来自美...     

陀螺电机转子动平衡激光精密去重技术

陀螺电机转子动平衡采用的人工打孔去重存在效率低、去重精度低、金属碎屑残留等问题，严重制约了陀螺的生产效率和精度。而激光去重具有去重精度高、无接触、效率高等优点，在精密去重领域应用前景广泛。采用脉冲光纤激光器对陀螺电机转子动平衡进行了激光精密去重技术研究，探讨了激光频率、振镜扫描速度等参数对去重效果的影响规律，优化了激光去重工艺参数。当激光功率为30W、振镜扫描速度为1000mm/s时，去重盲孔效果最好。针对激光去重盲孔存在残留物问题，提出了激光二次抛光去除残留物的方法，研究了激光功率、振镜扫描速度对残留物去除效果影响规律，优化了激光抛光工艺参数。激光去重盲孔经二次扫描抛光后，盲孔表面残留物去除干净，满足陀螺电机转子的精密去重要求。     

激光脉冲圈焊工艺研究与应用

基于有限元软件MSC.MARC软件平台Hypermesh软件模块仿真模拟了激光连续圈焊和激光脉冲圈焊的温度场分布,模拟结果表明:激光脉冲圈焊可有效控制被焊工件温度场分布,焊接热影响区小,为此采用激光脉冲圈焊工艺焊接簧片式电磁阀簧片组件.研究了激光焊接频率与焊点重叠率以及激光焊接速度与焊缝强度和焊点重叠率之间的关系,从而得出了激光脉冲圈焊焊接工艺规范,即激光峰值功率Pf--300 W,激光基值功率Pj=200 W,激光焊接速度v=3.33 mm/s,激光频率f=20 Hz等,采用该焊接规范焊接完成的簧片式电磁阀已经应用于嫦娥五号探测器推进分系统、轨道器子系统以及上升器推进子系统的液体动力装置之中,并已经完成了飞行和月球探测任务.     

基于激光旋切法的陶瓷材料盲孔加工方法研究

介绍了激光打孔的基本原理,对激光能量、离焦量、轨迹在激光旋切法加工盲孔过程中对孔形和表面质量的影响进行了分析和试验验证,并给出了一般规律.依据试验结果确定了合理工艺参数,采用旋切法在碳纤维增强碳化硅陶瓷基复合材料（Cf/SiC）上打出了孔径为1 mm,孔深为1.1 mm,锥度小于15°的盲孔.     

电极面型对横向激励高气压CO2激光器放电的影响

计算并讨论了均匀场电极中电极板安装结构、电极板厚度对实际电场分布影响。计算表明在基本参数类似的条件下,近罗可夫斯基电极表面电场强度具有17%的非均匀性,但在垂直放电方向的对称面上却有更好的均匀性。对放电区辉光的时间积分照片和像增强型CCD相机记录的瞬态照片进行了分析,结果表明:电极表面的电场强度分布,仅对放电的初始发展具有影响,而放电区中央的电场分布以及预电离强度,对最终放电区的均匀性具有决定性的影响。     

PULSED Nd-YAG LASER WELDING OF AN AI-SiC_p METAL MATRIX COMPOSITE

SupportedbytheNationalNaturalScienceFoundationofChinaThefewweldingtechniques,includinggastungstenarcwelding,gasmetalarcweldingandelectronbeamwelding,whichhavebeenexploredforjoiningofMMCs,werefoundtobeunsatisfactorymainlyduetotheformationofexcessivebrittleAl-carbidephase["2'J.Never-theless,limitedsuccesshasbeenachievedinusingCO,laserstoweldcertaintypesofAl-Si/SiCMMCs[s'J.Themeritsoflaserweldingareapparent:theintrinsicfocusingabilityandtheca-pabilityofhavingprecisecontroloverthelaserpro…     

激光辐照对钢试样疲劳寿命的影响

 讨论了棒形钢试样的疲劳寿命与激光辐照参量、硬度、层深间的关系。     

哈尔滨空气动力研究所近期发展的几项流态观察与显示技术

本文介绍了哈尔滨空气动力研究所近期发展的三项流态观察与显示技术,即彩色氦气泡流态显示,复合式片光流态显示和计算机控制的彩色图像流态显示技术。给出了它们的基本工作原理,主要技术性能和应用。     

激光干涉技术在振动冲击中的应用

振动冲击计量标准中采用激光干涉仪作为量值溯源工具，本文就振动冲击实验室应用的两类干涉仪从光学原理方面进行一些简单的分析对比。给出了二者之间的一些相同和类似点。