严格伪压缩映象的Ishikawa迭代序列

证明了Ｌ＾ｐ（或ｌ＾ｐ）（Ｐ≥２）上的李普希茨严格伪压缩映象的Ｉｓｈｉｋａｗａ迭代序列必收敛到映象的不动点。     

离散系统仿真输出数据的统计分析

概括了分析仿真产生的数据的方法，讨论了离散系统仿真输出分析的目的以及应用统计方法的要求，对单变量情形，给出了有关估计来自终态仿真和和稳态仿真参数的技术。对多变量情形，以终态仿真为例，给出了用于分析离散系统的仿真输出的某些多变量统计技术，并提出均值向量的估计方法。     

一个新的蠕变寿命估算公式的推出

本文从一些经典公式出发,推导出新的寿命公式。另外,通过引入蠕变损伤特征参量的概念还导出类似的另一个蠕变寿命估算公式。所推导出两个公式在16MnR材料中得到较为成功的应用。     

综合后勤保障及其在工程系统研制中的应用

探讨了综合后勤保障在工程系统研制中的重要作用,及其在研制过程各个阶段中的应用。还讨论了保障性设计与工程设计接口关系及保障性设计中的风险分析。     

轴对称跨音速流中无激波超音速区的设计

本文直接从音速线出发计算了一个旋成体跨音速绕流超音速泡中的特征线网。提出了从音速线开拓到一条超音速线的方法,计算了无旋轴对称流的特征线网,发现其特点是不能跨越对称轴线,并对其原因作了初步的讨论。本文的计算结果可应用于物面修形。     

防止Ⅱ型驾驶员诱发振荡技术的研究

许多严重的飞行事故都与由速率限制引起的Ⅱ型PIO有关。针对如何预防PIO，首先介绍了自适应杆增益和软件限制环节的设计原理。然后以某带速率限制的电传飞机为例，运用同一理论，分析采用自适应杆增益和软件限制环节来改善速率限制的不利影响。仿真结果表明，自适应杆增益环节和软件限制环节都能抑制住PIO的发生，但两者组合加入抑制效果更好，飞行品质也能达到满意的程度。     

冲击响应谱（SRS）分析数字化方法探讨

本文介绍了求单自由度二阶系统冲击响应谱（ＳＲＳ）的几种常用的数字化分析方法：直接积分法；快速富氏变换（ＦＦＴ）法；递推法；数字滤波器方法；改进的数字滤波器方法。并比较了它们的优缺点。     

用非线性模型分析气动液阀的启动特性

对气动液阀的启动过程建立了非线性数学模型,分析了尺寸参数和推进剂进、出口压力对该阀的启动特性的影响。计算结果表明：在保证必要的工作寿命的前提下,适当地增大控制腔气孔的直径或增大靠近控制腔的活塞端面直径,降低推进剂进口和出口的压力有利于提高该阀的响应能力。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

Study on the Microstructure and Dielectric Properties of Barium Strontium Titanate Thin Films Prepared by Sol-gel Method

Sr05Ba0.5-xBixTiO3 （BST） thin films were fabricated on a Pt/SiO2/Si substrate by the sol-gel method. Then follows an investigation of the influeoces of bismuth （Bi） on the microstructures and the dielectric properties of Sr0.5Ba0.5-xBixTiO3 （BST） thin films. The microstructures of the BST thin films were examined by the XRD and the TEM techniques. Tetragonal perovskite crystal grains were observed in BST thin films. Increasing Bi^3＋ doping ration in BST will lead to decrease of the grain size. It is found that Bi^3＋ doping decreases the dielectric loss and improves the frequency dispersion of the BST thin films. Not only is compressed the peak of temperature-dependence of dielectric constant of Bi^3＋-doped BST thin films but also moves into the low-temperature region. Moreover, the average Curie tem- perature decreases gradually with the Bi^3＋ contents increasing.