深化失效学的哲学理念探索,强化材料失效交叉技术研究

力图从哲学的高度,对失效学的认识论、矛盾论、系统论和方法论进行简要的阐释,从中提出一些要点,并对失效学哲学理念在失效事故分析诊断预防技术中的应用提出建议,为深化失效学的哲学理念探讨奠定初步基础。从失效学的理论基础、应用基础和工程技术等3个方面总结提出了失效学的理论和技术体系,为失效学的体系建设提供了技术框架;还从材料服役前、使用中和失效后等3个阶段归纳了材料失效交叉技术领域中的科学问题或关键技术,为加强其交叉技术的研究提炼出了若干重点方向。     

氙离子推力器束流分布特性研究

建立了离子推力器束流分布的高斯模型,以200mm氙离子推力器为例,在不同工作环境下对推力器束流分布进行了数值模拟,并通过试验测量了推力器引出切面不同位置(轴向z=50mm,z=100mm)下的径向束电流密度和束离子密度分布。通过对数值模拟结果与试验测量结果的比较,误差为17%,认为数值模拟结果与试验测量结果吻合较好。表明离子推力器引出束流呈轴对称分布,在推力器出口附近,束离子密度很大,越往下游,密度越小且束流出现发散。     

Mechanical behavior and properties of fiber reinforced ceramic matrix composites for high temperature use

Ceramics can keep their mechanical characteristics up to 2 000℃ or higher.In this paper,A model to predict ultimate strength of continuous fiber-reinforced brittle matrix composites is developed.A statistical theory for the strength of a uni-axially fiber-reinforced brittle matrix composite is presented.Also a semi-empirical frictional heating method for estimating in-situ interfacial shear in fiber-reinforced ceramic matrix composites was improved.Local uneven fiber packing variation as well as uneven micro-damage during fatigue can be expected to have effects on the composites:generation of frictional heating,thermal gradients,and residual stresses around local fiber breaks.This study examined those engineering interests by the finite element method.      

Study on the breakup lengths of free round liquid jets

IntroductionBreakup and atomization of roundliquidjetshad been widely used in internal combustion en-gines,gas turbines,and liquid rocket engines.Recently,with the development of scramjet en-gines and the deepening of fuel atomization re-search,it attract…     

Microstructure and Martensitic Transformation Behaviors of Explosively Welded NiTi/NiTi Laminates

The study is a first attempt to prepare bulk NiTi/NiTi shape memory alloy (SMA) laminates with a macroscopic heterogeneous composition by explosive welding and investigate their microstructures and martensitic transformation behaviors. After explosive weld- ing, a perfect interfacial bonding between the two components and a reversible martensitic transformation are realized in the tandem. Results show achievement of a fine granular structure and the maximum value of microhardness near the welding interface because of the excessive cold plastic deformation and the high impact velocity during the explosive welding. Meanwhile, the effects of aging on the transformation of the welded tandem are investigated by differential scanning calorimeter (DSC) and subject to discussion. The trans- formation temperatures of NiTi/NiTi SMAs increase with the rise of the aging temperature. The experimental results indicate the shape memory properties of NiTi/NiTi SMA fabricated by explosive welding can be improved by optimizing the aging technology.     

New Cutting Force Modeling Approach for Flat End Mill

A new mechanistic cutting force model for flat end milling using the instantaneous cutting force coefficients is proposed. An in-depth analysis shows that the total cutting forces can be separated into two terms: a nominal component independent of the runout and a perturbation component induced by the runout. The instantaneous value of the nominal component is used to calibrate the cutting force coefficients. With the help of the perturbation component and the cutting force coefficients obtained above, the cutter runout is identified. Based on simulation and experimental results, the validity of the identification approach is demonstrated. The advantage of the proposed method lies in that the calibration performed with data of one cutting test under a specific regime can be applied for a great range of cutting conditions.     

Investigation on the Thermal Conductivity of 3-Dimensional and 4-Directional Braided Composites

It is vital to choose a factual and reasonable micro-structural model of braided composites for improving the calculating precision of thermal property of 3-D braided composites by finite element method (FEM). On the basis of new microstructure model of braided composites proposed recently, the model of FEM calculation for thermal conductivity of 3-dimennsional and 4-directional braided composites is set up in this paper. The curves of coefficient of effective thermal conductivity versus fiber volume ratio and interior braiding angle are obtained. Furthermore, comparing the results of FEM with the available experimental data,the reasonability and veracity of calculation are confirmed at the same time.     

Periodic Error Compensation for Quartz MEMS Gyroscope Drift of INS

In order to improve the navigation accuracy of an inertial navigation system （INS）, composed of quartz gyroscopes, the existing real-time compensation methods for periodic errors in quartz gyroscope drift and the periodic error term relationship between sampled original data and smoothed data are reviewed. On the base of the results, a new compensation method called using former period characteristics to compensate latter smoothness data （UFCL for short） method is proposed considering the INS working characteristics. This new method uses the original data without smoothing to work out an error conversion formula at the INS initial alignment time and then compensate the smoothed data errors by way of the formula at the navigation time. Both theoretical analysis and experimental results demonstrate that this method is able to cut down on computational time and raise the accuracy which makes it a better real-time compensation approach for periodic error terms of quartz micro electronic mechanical system （MEMS） gyroscope＇s zero drift.     

永磁约束电子束轨迹实验研究

通过设计并运用一种直流电子束轨迹简易测量方法,开展了永磁约束电子束轨迹实验研究,得到了永磁铁环对60~80 ke V电子束约束作用的实验数据。结果表明:该测量方法方便有效,结果较为准确;永磁铁对电子束聚焦作用明显,并呈现出一定的规律性。对永磁铁约束电子束研究工作奠定了基础。     

类IXV飞行器初期再入制导与姿态控制方法研究

摘要： 针对类IXV飞行器无翼式升力体构型及采用RCS/尾襟翼组合控制特点,研究其初期再入段的高精度制导与姿态控制方法.设计带过程约束的数值预测 校正制导律以提高制导系统的鲁棒性及精确性;根据其执行机构配置特点,设计基于RCS的航向控制律及基于RCS/气动舵的纵、横向复合控制律,并采用鲁棒伺服LQR技术进行控制参数快速设计.通过蒙特卡洛打靶仿真来验证算法的精度及鲁棒性.