航空发动机叶片高频模态阻尼的实验测试方法

以NASA Rotor37叶片为对象,研究了航空发动机叶片的高频模态阻尼比的实验测试方法.实验分析和数值计算均说明:在随机声激励下获得频响曲线将包含由支撑结构振动造成的峰值.基于此提出在支撑结构上布置多个传感器的实验方案,并以支撑结构的振动峰值位置和能量相对大小来判定叶片振动主导的振动峰值.用小波阈值收缩法和曲线拟合法对这些振动峰值进行了降噪和模态阻尼比识别,给出了实测模型在10kHz内“叶片主导振动”的模态阻尼比.结果表明:一般的结构金属材料条件下,叶片结构的高频模态阻尼比的数量级小于1%,且随频率增加呈下降趋势.      

双级波瓣引射混合器的引射性能

采用实验和数值方法对双级波瓣引射混合器的引射性能进行研究,重点研究混合管在两种不同进口方式下的引射混合器气动特征差异,并初步分析混合管面积比和长径比对双级波瓣引射混合器引射性能的影响.结果表明:混合管进口方式对引射能力有非常重要的影响,在研究的结构参数条件下,对于受限式进口,单级波瓣引射混合器的引射能力要强于双级波瓣引射混合器约10%;而对于敞开式进口,其引射能力要优于受限式进口最大约35%,此时双级波瓣引射混合器的引射能力要略好于单级波瓣引射混合器.在较大的混合管面积比或较小的长径比下,敞开式进口下双级波瓣引射混合器较受限式进口表现尤为优越.      

高旋转数内冷通道换热实验技术及验证

通过内冷通道换热理论分析及实验系统优化,获得了使内冷通道内气体压力保持在500kPa以上的高旋转数实验技术.旋转数和雷诺数的范围分别为0~2.08,104~7×104,极大满足了旋转数与雷诺数同时覆盖真实发动机涡轮叶片工作参数的实验需求.证实了雷诺数和旋转数对内冷通道换热的影响可以解耦.而应用该实验技术进行同等旋转数实验时,内冷通道热损失占总加热量的比例和实验误差分别降低到18%和±10%.     

同应力多危险部位轮盘寿命可靠性试验评估方法

讨论了轮盘寿命试验评估中基于威布尔分布和对数正态分布的寿命分散系数法。提出两种多危险部位轮盘寿命试验评估的改进分散系数估计法,并以某轮盘概率寿命评估为例说明了改进方法的应用。     

降落伞的流场特性研究

降落伞的流场特性直接关系到降落伞的气动力性能,一直以来是降落伞研究中的核心问题。本文采用计算流体动力学(CFD)方法对降落伞的流场进行数值模拟。通过采用不同的网格生成方法对降落伞的绕流流场进行研究,表明生成网格质量对流场计算精度有很大的影响。在一系列数值实验的基础上,证明采用多块贴体坐标的网格处理方法能够获得良好的网格质量,同时还具有易于寻找伞衣内外面压力,计算稳定性、可靠性高等优点。在此基础上,采用了七孔探针对降落伞绕流流场进行了测量,实验结果和计算结果吻合较好。     

Microstructure and Martensitic Transformation Behaviors of Explosively Welded NiTi/NiTi Laminates

The study is a first attempt to prepare bulk NiTi/NiTi shape memory alloy (SMA) laminates with a macroscopic heterogeneous composition by explosive welding and investigate their microstructures and martensitic transformation behaviors. After explosive weld- ing, a perfect interfacial bonding between the two components and a reversible martensitic transformation are realized in the tandem. Results show achievement of a fine granular structure and the maximum value of microhardness near the welding interface because of the excessive cold plastic deformation and the high impact velocity during the explosive welding. Meanwhile, the effects of aging on the transformation of the welded tandem are investigated by differential scanning calorimeter (DSC) and subject to discussion. The trans- formation temperatures of NiTi/NiTi SMAs increase with the rise of the aging temperature. The experimental results indicate the shape memory properties of NiTi/NiTi SMA fabricated by explosive welding can be improved by optimizing the aging technology.     

New Cutting Force Modeling Approach for Flat End Mill

A new mechanistic cutting force model for flat end milling using the instantaneous cutting force coefficients is proposed. An in-depth analysis shows that the total cutting forces can be separated into two terms: a nominal component independent of the runout and a perturbation component induced by the runout. The instantaneous value of the nominal component is used to calibrate the cutting force coefficients. With the help of the perturbation component and the cutting force coefficients obtained above, the cutter runout is identified. Based on simulation and experimental results, the validity of the identification approach is demonstrated. The advantage of the proposed method lies in that the calibration performed with data of one cutting test under a specific regime can be applied for a great range of cutting conditions.     

Investigation on the Thermal Conductivity of 3-Dimensional and 4-Directional Braided Composites

It is vital to choose a factual and reasonable micro-structural model of braided composites for improving the calculating precision of thermal property of 3-D braided composites by finite element method (FEM). On the basis of new microstructure model of braided composites proposed recently, the model of FEM calculation for thermal conductivity of 3-dimennsional and 4-directional braided composites is set up in this paper. The curves of coefficient of effective thermal conductivity versus fiber volume ratio and interior braiding angle are obtained. Furthermore, comparing the results of FEM with the available experimental data,the reasonability and veracity of calculation are confirmed at the same time.     

频率30~50Hz两相脉冲爆震发动机研究

设计了一台内径58mm,长度1275mm的脉冲爆震发动机(PDE)原型机。采用地面充压进气,在工作频率30~50Hz的工况下研究PDE爆震管内的压力波特性。试验发现,该PDE样机在频率50Hz以内都能够稳定的以间歇方式工作,爆震波峰值压力大于1.6MPa;随着PDE工作频率的提高,工作频率为45~50Hz时,比40Hz以下工作频率提前触发了爆震波,且爆震波得到了充分的发展。     

喷气燃料中微量悬浮物的过滤分离装置的研制

研制了喷气燃料中难分离微量悬浮物的过滤试验装置,通过标准试验手段来判断某喷气燃料中的悬浮物是否能够通过目前外场过滤系统过滤净化处理,减少目前普遍使用的用目视检查方法判断喷气燃料洁净度的误差。研制的标准滤芯满足设计要求。按照标准试验滤芯相似原理即过滤精度、流量和压差三方面相似设计的标准滤芯与小型滤芯和外场大滤芯效果相当,在5~9级范围内AbakusC颗粒计数仪测得的NAS1638污染度可以代替俄罗斯ПКЖ-904A颗粒计数仪测得的ΓOCT17216污染度。使用过滤试验装置有利于对喷气燃料质量管理和贮运过程中的洁净度进行科学评价。