神舟2号大气密度探测器的探测结果(Ⅰ)日照和阴影区域热层大气密度变化

选用了神舟2号（SZ-2）大气密度探测器在2001年2—4月间的探测数据,进行日照和阴影区域热层大气密度变化的探讨.结果表明:在高度410km附近,日照和阴影区域大气密度变幅为2—3倍,变幅的大小与地磁活动程度呈负相关关系.日照面大气密度峰区位于星下点地方时1400—1500LT的纬度处,峰值大小与太阳活动程度呈正相关关系.阴影面大气密度谷区位于星下点地方时0400-0500的纬度处,同时在±10°纬度区域中还出现了阴影面峰区.     

MONITORING OF ENERGETIC PARTICLE ENVIRONMENT INSIDE THE CHINA-BRAZIL EARTH RESOURCE SATELLITE

On 14 October 1999, the Chinese-Brazil earth resource satellite (CBERS-1) was launched in China. On board of the satellite there was an instrument designed at Peking University to detect the energetic particle radiation inside the satellite so the radiation fluxes of energetic particles in the cabin can be monitored continuously. Inside a satellite cabin, radiation environment consists of ether penetrated energetic particles or secondary radiation from satellite materials due to the interactions with primary cosmic rays.Purpose of the detectors are twofold, to monitor the particle radiation in the cabin and also to study the space radiation environment The data can be used to study the radiation environment and their effects on the electronics inside the satelhte cabin. On the other hand, the data are useful in study of geo-space energetic particle events such as solar proton events, particle precipitation and variations of the radiation belt since there should be some correlation between the radiation situation inside and outside the satellite.The instrument consists of two semi-conductor detectors for protons and electrons respectively. Each detector has two channels of energy ranges. They are 0.5-2MeV and ≥2MeV for electrons and 5-30MeV and 30-60MeV for protons. Counting rate for all channels are up to 104/(cm2@s)and power consumption is about 2.5 W. There are also the additional functions of CMOS TID (total integrated dose) effect and direct SEU monitoring. The data of CBMC was first sent back on Oct. 17 1999 and it's almost three years from then on. The detector has been working normally and the quality of data is good.The preliminary results of data analysis of CBMC not only reveal the effects of polar particle precipitation and radiation belt on radiation environment inside a satellite, but also show some important features of the geo-space energetic particle radiation.As one of the most important parameters of space weather, the energetic charged particles have great influences on space activities and ground tech nology. CBMC is perhaps the first long-term on-board special equipment to monitor the energetic particle radiation environment inside the satellite and the data it accnmulated are very useful in both satellite designing and space research.     

半浮区液桥自由面振荡特征

使用一套双路同步显微放大录像及图像处理系统,研究了夹角为90°的两个竖直剖面沿轴向不同高度液桥自由表面的位移振荡,得到轴向不同高度上的环向相位差,观测到在振荡周期内液桥表面轮廓线在不同时刻均不相交的特点。实验结果表明,液桥自由面振荡除具有径向扰动及轴向振荡变化外,还存在环向波动变化。根据实验结果,讨论了环向波动基本变化规律以及本实验在测量精度和测量误差方面存在的问题。     

数字化技术在叶轮研制中的应用

本文通过分析归纳建立了一种叶轮数字化建模方法，并利用该方法成功实现了某型叶轮三维模型创建，同时也根据该数字化模型实现了模具数字化设计及其数控加工。     

基于激光的便携式飞机装配接缝质量检测仪及应用

介绍了一种基于激光的便携式接缝质量检测仪的工作原理及硬件组成。使用该检测仪对飞机缝隙和台阶阶差进行了测量,通过与人工测量进行对比验证,证明了该装置可实现对特征三维信息的快速自动检测,工作准确可靠。     

一种叶片截面线光顺及等距面生成方法

采用等距面生成球头刀加工刀具轨迹是曲面加工中一种常用的方法。但是,在对叶身曲面进行等距偏置时,经常出现无法偏置的问题。针对该问题,分析了曲面偏置自相交原因,并根据叶片类零件叶身曲面的特点,提出了一种叶身截面线光顺及等距面生成方法。该方法首先采用Kjellander方法将原始截面线进行自动光顺,然后根据光顺后的原始截面线和数据采样法构造偏置截面线,最后通过截面线放样法构造叶身曲面等距面。实例表明,采用Kjellander方法可以实现叶片曲面的自动光顺和叶片曲面等距面的构造。     

A time-frequency analysis of the thermal radiation background anomalies caused by large earthquakes: A case study of the Wenchuan 8.0 earthquake

Strong earthquakes have an impact on the regional thermal radiation background, which has been both observed and confirmed. This effect produces anomalies in the thermal radiation background (TRBA) and increases the difficulty of extracting a thermal radiation anomaly (TRA) that is associated with an earthquake occurring during the same time period. The extraction and identification of such anomalies has been ignored by previous studies. In this study, we investigate the time-frequency analysis (TFA) method, together with the wavelet filtering of the Daubechies method and the relative power spectrum analysis of the Fourier Welch method to extract and analyse the TRBA caused by the 2008 Wenchuan Ms 8.0 earthquake and the TRA of the 2013 Minxian-Zhangxian Ms 6.6 earthquake using data concerning the brightness temperature of a black body (TBB) from the Fengyun-2 series of geostationary meteorological satellites developed by China. The result showed that this method can effectively extract and analyse the TRBA caused by the Wenchuan earthquake and the TRA of the Minxian-Zhangxian earthquake form a complex background environment. Furthermore, we discussed the impact of the earthquake on the TRBA and segmented the process. The impact is mainly reflected by three aspects; the characteristic period of the TRBA changes, the TRBA occurs at the same time every year, which is identical to the time at which the earthquake anomaly occurred, and the impact process is in stages. We also summarized the correlation between the characteristic parameters of a TRA and the regional thermal radiation background, geography, and climatic factors.     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.     

压气机叶片型面精密数控铣加工技术应用研究

为了提高压气机叶片型面和进、排气边转接圆角的数控铣加工质量,在工艺、夹具、数控加工模型与程序以及检测方法等方面采取了攻关措施,减小了叶片型面精铣加工的变形,实现了叶身型面的精密铣削加工,对型面采用毡轮修光去除铣削痕迹后,经过3坐标、小半径投影仪等设备的测量,进、排气边转接圆角的形状和型面轮廓度、位置度各项要求的加工质量得到了质的提升,其合格率由20％提高到75％以上,加工效率和刀具耐用度提高1倍以上,使叶身型面精密铣削技术具备了精品叶片批量生产的工程化应用技术基础.     

基于响应面法的齿轮容差设计方法研究

随着附件传动系统不断向高速、重载方向发展,齿面接触可靠性问题越来越受关注.为提高齿轮可靠性,分析了齿轮传动系统常见误差类型及影响,开展了齿轮容差设计初步探讨.根据齿轮制造、加工及系统动态误差的产生原理和作用方式,基于齿轮接触应力仿真结果,确定了影响齿轮接触应力随机性的5种主要误差形式及其特征量分布规律,提出了基于响应面法的齿轮容差设计方法,给出了齿轮系统公差设计的改进方向:在进行齿轮公差设计时,重点控制H、V方向的轴向平行度公差.