基于6SPS并联机构标定新方法

系统研究6SPS并联机构标定的方法。研究中应用激光跟踪仪测量、基于并联机构正解和定位误差旋量的计算,正交试验进行试验设计,应用非线性最小二乘参数辨识。仿真验证辨识的几何误差可以等于假定值,试验验证位姿精度提高了10倍。     

Application of small-size antennas for estimation of angles of arrival of HF signals scattered by ionospheric irregularities

A modification of the Doppler Interferometry Technique is suggested to enable estimating angles of arrival of comparatively broadband HF signals scattered by random irregularities of the ionospheric plasma with the use of small-size weakly directional antennas. The technique is based on the measurements of cross-spectra phases of the probe radiation recorded at least in three spatially separated points. The developed algorithm has been used to investigate the angular and frequency-time characteristics of HF signals propagating at frequencies above the maximum usable one (MUF) for the direct radio path Moscow-Kharkiv. The received signal spectra show presence of three families of spatial components attributed, respectively, to scattering by plasma irregularities near the middle point of the radio path, ground backscatter signals and scattering of the sounding signals by the intense plasma turbulence associated with auroral activations. It has been shown that the regions responsible for the formation of the third family components are located well inside the auroral oval. The drift velocity and direction of the auroral ionosphere plasma have been determined. The obtained estimates are consistent with the classical conception of the ionospheric plasma convection at high latitudes and do not contradict the results of investigations of the auroral ionosphere dynamics using the SuperDARN network.     

ZYTC600专用镗床精密转台微调机构设计与分析

为解决框架类零件的高位置度孔的精密镗削加工问题,研发了ZYTC600专用镗削机床.其精度指标优于现有的通用镗床(包括进口镗床),尺寸在500mm范围内,同轴度优于2μm,垂直度优于5μm,其中的关键部件双回转轴系分度精密转台采用了一套精密调整机构,可以实现0.2s”的精密调整,通过有限元分析得到其驱动刚度可达到800N/μm,可以满足加工需求.     

基于H∞方法的控制系统作动器最优控制仿真研究

在设计控制系统模型时,首先引入了有限差分法(FDM)离散化后的波动方程,然后基于H∞最优控制原理,检查闭环控制系统的稳定性和可探测性,对控制系统传感器和作动器的位置进行优化配置.通过计算闭环反馈系统的范数,最终得到了控制系统的最优控制算法.仿真结果表明,利用波动方程来优化控制系统传感器和作动器位置的算法是可行的,可广泛应用于飞控系统的设计中.     

一种卫星信道的反馈优化接入机制

提高卫星信道资源利用率，探索高效可行的端站接入机制是卫星通信发展亟待解决的问题之一。当前卫星通信DVB-RCS标准基于带宽预先规划的接入机制与端站随遇接入的需求矛盾凸显，因此提出一套信道反馈优化接入机制，综合考虑各端站数据业务需求，在不改变原有协议信令特征的基础上，探索性地引入谦虚度激励方法，创造性地构造动态协商反馈模型并加以求解，达到提高端站接入数量、满足随遇接入需求、提升信道利用效率、最大化整体带宽通信业务效益的目的。通过试验验证，带宽分配反馈优化机制比传统模式提高近1倍接入率，最大端站数接入时算法耗时约只有0.67s，可为卫星信道使用提供技术参考。     

低速大转矩永磁游标电机在发酵罐中的应用

采用秸秆生产丁醇时,为了达到高效率发酵,需要使发酵液中菌体分布均匀,所加物料需要及时搅拌。工业化生产丁醇的发酵罐尺寸较大,搅拌过程对驱动电机的输出转矩要求较高,因此高效率、小体积、低速大转矩的秸秆发酵搅拌电机对工业化发酵生产丁醇意义重大。设计了一种定转子永磁游标电机用于发酵液搅拌,并对电机的槽极数、电磁性能进行了具体的研究。制造样机并采用滞环控制实现了对液态发酵对象的快速响应,且实现了低能耗、高效率的发酵过程。     

Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.     

某型教练机嵌入式训练系统顶层设计技术研究

本文通过对该型教练机现有航空电子系统构型、驾驶员操作程序、接口控制文件深入研究,结合未来功能扩展需求,给出了合理的系统构型分析、功能分配、数据流规划、原相关系统软件改动分析,在此基础上还设计出了嵌入式训练系统技术方案.依据方案研制的嵌入式训练系统原理样机通过系统动态试验、航电系统地面综合试验和飞机地面通电试验,证明系统...     

HED-21S数控综合实验台画笔自动控制机构设计

以数控系统的PLC控制为基础,设计HED-21S机械笔控制系统结构,它可控制电磁铁的动作,执行画笔的上下运动。这支笔在X、Z型十字窗格可以绘制任意几何形状,该设计符合要求的快速定位数控直线移动,及圆弧插补功能,有助于提高数控编程效率和数控教学质量。